2001 TOYOTA SEQUOIA lights

H20776
SST SST
R05181
10 m (33 ft) or more
H20777
BO±170
± BODYSEAT BELT PRETENSIONER
3723 Author: Date:
2005 SEQUOIA (RM1146U)
(2) Place the front seat outer belt on the ground and
cover it with the disc wheel with tire.
NOTICE:
Place the front seat outer belt as shown in the illustration.
(3) Move the SST to at least 10 m (33 ft) away from the
disc wheel.
NOTICE:
Take care not to damage the SST wire harness.
(d) Activate the seat belt pretensioner.
(1) Connect the SST red clip to the battery positive (+)
terminal and black clip to the battery negative (±)
terminal.
(2) Check that no one is within 10 m (33 ft) area around
the disc wheel.
(3) Press the SST activation switch and activate the
seat belt pretensioner.
HINT:
The seat belt pretensioner operates simultaneously as the LED
of the SST activation switch lights up.
(e) Dispose of the front seat outer belt (with seat belt preten-
sioner).
CAUTION:

The front seat outer belt is very hot when the seat belt
pretensioner is activated, so leave it alone for at least
30 minutes after activation.

Use gloves and safety glasses when handling a front
seat outer belt with activated seat belt pretensioner.

Always wash your hands with water after completing
the operation.

Do not apply water, etc. to a front seat outer belt with
activated seat belt pretensioner.
(1) Remove the disc wheel and SST.
(2) Place the front seat outer belt in a vinyl bag, tie the
end tightly and dispose of it in the same way as oth-
er general parts.

AC3HQ±02
I21379
I22616
1 2
4
I17711
3
4 AC±84
± AIR CONDITIONINGPOWER TRANSISTOR (for Rear A/C)
3811 Author: Date:
2005 SEQUOIA (RM1146U)
POWER TRANSISTOR (for Rear
A/C)
INSPECTION
1. REMOVE REAR SEAT OUTER BELT FLOOR AN-
CHORS
2. REMOVE BACK DOOR SCUFF PLATE
3. REMOVE REAR DOOR SCUFF PLATE RH
4. REMOVE REAR WINDOW SIDE GARNISH
5. REMOVE REAR QUARTER TRIM PANEL RH
6. REMOVE REAR POWER TRANSISTOR
(a) Disconnect the connector.
(b) Remove the 2 screws and the rear power transistor.
7. INSPECT POWER TRANSISTOR OPERATION
(a) Connect the positive (+) lead to terminal 1 through a
12 V ± 3.4 W test bulb and the negative (±) lead to
terminal 4.
(b) Check the test bulb lights up when another positive (+)
lead is connected to terminal 2 through a 12 V ± 3.4 W test
bulb.
If operation is not as specified, replace the power transistor.
8. INSPECT POWER TRANSISTOR RESISTANCE
Measure the resistance between terminals 3 and 4.
Standard resistance: 2.0 to 2.4 kW
If resistance is not as specified, replace the power transistor.
9. INSTALL REAR POWER TRANSISTOR
10. INSTALL REAR QUARTER TRIM PANEL RH
11. INSTALL REAR WINDOW SIDE GARNISH
12. INSTALL REAR DOOR SCUFF PLATE RH
13. INSTALL BACK DOOR SCUFF PLATE

05_SEQUOIA_U (L/O 0408)
2
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
1. Side vents
2. Instrument cluster
3. Center vents
4. Multi±information display
5. Personal lights
6. Garage door opener box or auxiliary
box
7. Electric moon roof switches
8. Side defroster outlet
9. Glove box
10. Power door lock switches
11. Power window switches
12. Power outlets
13. Seat heater switches
14. Rear console box
15. Rear air conditioning controls
16. Headphone input jacks and headphone
volume control dials
17. Input terminal adapter
18. Cup holders
19. Power rear view mirror control switches
20. Lower vent
Instrument panel overview

View A

05_SEQUOIA_U (L/O 0408)
8
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
1. Service reminder indicators and
indicator lights
2. Oil pressure gauge
3. Tachometer4. Speedometer
5. Fuel gauge
6. Engine coolant temperature gauge7. Trip meter reset knob
8. Odometer and two trip meters
9. Height control indicator lights
10. Volt meter
Instrument cluster overview

Ty p e A

05_SEQUOIA_U (L/O 0408)
9
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
1. Service reminder indicators and
indicator lights
2. Oil pressure gauge
3. Tachometer4. Speedometer
5. Fuel gauge
6. Engine coolant temperature gauge7. Trip meter reset knob
8. Odometer and two trip meters
9. Height control indicator lights
10. Volt meter
Ty p e B

05_SEQUOIA_U (L/O 0408)
11
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
Automatic transmission indicator lights
Traction control system off indicator light
(two±wheel drive models)
Vehicle stability control system off indicator light
(four±wheel drive models) Slip indicator light
Headlight high beam indicator lightOverdrive±off indicator light
Turn signal indicator lights
Engine immobilizer/theft deterrent system
indicator light
Front passenger occupant classification
indicator light
Roll sensing of curtain shield airbags off
indicator light
Headlight low beam indicator light
Tail light indicator lightLow speed four±wheel drive indicator light*
2
High speed four±wheel drive indicator light*
2
Center differential lock indicator light*
2
(four±wheel drive models)

05_SEQUOIA_U (L/O 0408)
12
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
Cruise control indicator light*
4
*
1
: For details, see ªService reminder indicators and warning
buzzersº on page 162 in Section 1±6.
*
2: If this light flashes, see ªFour±wheel drive systemº on page
177 in Section 1±7.
*
3: If this light flashes, see ªRear height control air suspensionº
on page 189 in Section 1±7.
*
4: If this light flashes, see ªCruise controlº on page 205 in
Section 1±7.
Manual control mode indicator light*
3
Height control indicator lights

05_SEQUOIA_U (L/O 0408)
20
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
For vehicles sold in Canada
Operation is subject to the following two
conditions:
(1) this device may not cause interfer-
ence, and (2) this device must accept
any interference, including interference
that may cause undesired operation of
the device.
Locking operation
Unlocking operation
To lock and unlock all the side doors
and back door, push the switches slow-
ly and securely.
To lock: Push the ªLOCKº switch. All the
side doors and back door are locked si-
multaneously. At this time one beep will
be heard, and the parking lights and tail
lights flash once.
Check to see that all the side doors and
back door are securely locked.
If any of the side doors or back door is
not securely closed, locking cannot be
performed by the ªLOCKº switch and a
beep will sound continuously for 10 sec-
onds. However, if the key is in the igni-
tion, a beep will not sound.
To stop the beep, close all the side doors
and back door securely or push the ªUN-
LOCKº switch.
The beep can be disabled. For details,
contact your Toyota dealer.
ÐLocking and unlocking
doors