2001 TOYOTA SEQUOIA airbag

H23483CG
DLC3:
D6
H23040TC
A20
DI±1500
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1694 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check wire harness (CG of DLC3 ± body ground).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
D6±4 (CG) ± Body groundAlwaysBelow 1 W
NG Repair or replace wire harness (CG of DLC3 to
body ground).
OK
3 Check wire harness (TC of airbag sensor assembly ± body ground).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
A20±15 (TC) ±
Body groundAlways1 MW or higher
NG Repair or replace wire harness or each ECU.
OK
Replace airbag sensor assembly (see page RS±82).

I28464
ECM
Sub J/B No.4
23
E4
1328
T5
15
A205
4E
TC
TC5
4B
5
4C 5
4D
5
4A 15
1F 9
1A
J43
J/C12
T17 P±B P±B Translate ECU
TCP±B
P±B
O
O 4 TC
CG D6
DLC3 Airbag Sensor
Assembly
Instrument Panel J/BTire Pressure
ECU
P±B
G
A A
IGTC
± DIAGNOSTICSCRUISE CONTROL SYSTEM
DI±1567
1761 Author: Date:
2005 SEQUOIA (RM1146U)
Diagnosis circuit
CIRCUIT DESCRIPTION
Making a short circuit between terminals TC and CG of the DLC3 will output DTCs from the DLC3.
WIRING DIAGRAM
HINT:
When a particular warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an
internal ground short in the relevant ECU is suspected.
DIDF5±01

DID8P±01
I28566
Seat Position
Control ECU
A/C ECU (Integration
Control Panel) BEANBody ECU
Back Door ECU
ECM
Light Control
Rheostat
Vehicle Speed
Sensor
Oil Pressure
Sender Gauge
Fuel Sender Gauge
Seat Inner
Belt Switch
Park/neutral
Position Switch
Turn Signal
Flasher Relay
Washer Level SensorKey Unlock
Warning Switch
Door Courtesy
Lamp Switch
Parking Brake Switch
Transponder
Key ECU
4WD Control ECU
Airbag Sensor
Center ECU Combination
Meter
Skid Control ECU
Suspension
Control ECU
Translate ECU
Overhead Module
(Garage Door
Opener)BEAN
BEAN
BEAN
BEAN
BEAN BEAN
± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1605
1799 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM

DID8Q±01
DI±1608
± DIAGNOSTICSCOMBINATION METER SYSTEM
1802 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DESCRIPTION
1. METER GAUGE AND WARNING/INDICATOR
GAUGE:
ItemDetail
SpeedometerVehicle speed sensor (Direct line).
TachometerECM transmits engine speed to the meter to display.
ODO/TRIP MeterCombination meter assy.
FuelDisplays a fuel level according to a signal from the fuel sender gauge (Direct line).
Water TemperatureDisplays engine coolant temperature according to a signal from the ECM (BEAN).
Oil PressureReceives a signal from the oil pressure sender (Direct line).
Volt MeterDisplays vehicle voltage according to a voltage from the IG terminal (Direct line).
WARNING/INDICATOR:
HINT:
Combination meter bulb check is performed for 3 seconds after the ignition switch is turned ON.
ItemDetailList of indicators available for
bulb check
O/D OFFReceives a signal from the ECM (Direct line)±
TURNTurns signal switch ON (Direct line)±
BEAMReceives a signal from the body ECU (*1), Displays a signal received from the
dimmer switch (*2) (Direct line)±
SECURITYReceives a set signal from the transponder key ECU and body ECU (Direct line)±
CHARGEReceives a malfunction signal from the alternator (Direct line)
AIR BAGReceives a malfunction signal from the airbag sensor center (Direct line)
D SEAT BELTReceives the driver seat belt signal (Unfastened) from the seat belt inner front LH
(Direct line)±
DOOROpen door indicator comes on when a signal is received from the ECU (BEAN)
from each door±
A/T OIL TEMP.Warning is displayed when the oil temperature is high (Direct line)
BRAKEComes on when the parking brake switch is on or the brake fluid level warning
switch is on (Direct line)
MIL (CHECK ENGINE)Receives a malfunction signal from the ECM (Direct line)
FUEL WARNINGReceives the fuel empty signal from the fuel sender gauge (Direct line)±
ABSReceives a malfunction signal from the skid control ECU (Direct line)
WASHERWarning is displayed when the washer level is low (Direct line)±
CRUISEReceives a CRUISE on signal or malfunction signal from the ECM (Direct line)±
VSC TRACReceives a malfunction signal from the skid control ECU (Direct line)
VSC (TRAC) OFFReceives a malfunction signal from the translate ECU (Direct line)
SLIPReceives a malfunction signal from the translate ECU (Direct line)
4HIReceives a 4HI signal from the 4WD control ECU (Direct line)±
CTR DIF LOCKReceives a DIF LOCK signal from the 4WD control ECU (Direct line)±
A/T PReceives a P signal from the park/neutral position switch (Direct line)±
A/T NReceives an N signal from the park/neutral position switch (Direct line)±
A/T DReceives a D signal from the park/neutral position switch (Direct line)±
A/T 3Receives a 3 signal from the park/neutral position switch (Direct line)±
A/T 2Receives a 2 signal from the park/neutral position switch (Direct line)±
A/T LReceives an L signal from the park/neutral position switch (Direct line)±

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1609
1803 Author: Date:
2005 SEQUOIA (RM1146U)A/T R
Receives an R signal from the park/neutral position switch (Direct line)±
TAIL/HEADReceives a dimmer signal from the body ECU (BEAN)±
TIRE PRESSUREReceives a low tire pressure signal from the tire pressure monitor ECU (Direct line)
4LOReceives a 4LO signal from the 4WD control ECU (Direct line)±
MAIN REQD (Blinks)Blinks when 4,500 miles have been traveled, after ODO/TRIP switch is set (Direct
line)
MAIN REQD (Comes on)Blinks when 5,000 miles have been traveled, after ODO/TRIP switch is set (Direct
line)
RSCA OFFReceives an RSCA OFF signal from the airbag sensor center (Direct line)
HIReceives a suspension position HI signal from the suspension control ECU (Direct
line)
NReceives a suspension position N signal from the suspension control ECU (Direct
line)
LOReceives a suspension position LO signal from the suspension control ECU (Direct
line)
AHC MAN.Receives a suspension control manual signal from the suspension control ECU
(Direct line)
*1: w/ Day time running light
*2: w/o Day time running light
BUZZER:
ItemDetail
Key ReminderBuzzer is ON: Ignition switch is OFF, key is inserted, and door is open.
Fasten BeltBuzzer is ON: Ignition switch is ON and seat belt is unfastened.
2. COMBINATION METER IN SEQUOIA HAS THE FOLLOWING FEATURES:
(a) Built±in buzzer for the reminder system (key and seat belt)
(b) Integrated trip and odometer knobs

Press and release knob to scroll through trip ºAº, trip ºBº, and odometer features.

Press and hold the trip knob to reset trip meter functions.
(c) Oil maintenance indicator

When 4,500 miles have been traveled, after the ODO/TRIP switch is set, the maintenance indica-
tor begins to blink for 15 seconds after the ignition switch is turned to the ON position.

When 5,000 miles have been traveled, after the ODO/TRIP switch is set, the maintenance indica-
tor comes on.

Press and hold the trip knob to reset the oil maintenance indicator.
(d) Rotate knob to adjust interior illumination

DID8U±01
DI±1614
± DIAGNOSTICSCOMBINATION METER SYSTEM
1808 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
HINT:
Inspect the related ºFuseº and ºRelayº before confirming the suspected area as shown in the table below.
MALFUNCTION SYSTEM:
SymptomSuspected AreaSee page
Entire combination meter does not operate.Refer to troubleshooting proceduresDI±1628
Operating light control rheostat does not change light brightness.Refer to troubleshooting proceduresDI±1645
Seat belt warning does not operate.Refer to troubleshooting proceduresDI±1650
Key reminder warning buzzer does not sound.
1. Multiplex communication system
2. Key unlock warning switch circuit
3. Door courtesy lamp switch circuit
4. Combination meter assyDI±1892
DI±1715
DI±1728
IN±35
METER GAUGES:
SymptomSuspected AreaSee page
Malfunction in speedometerRefer to troubleshooting proceduresDI±1632
Malfunction in tachometerRefer to troubleshooting proceduresDI±1636
Malfunction in fuel receiver gaugeRefer to troubleshooting proceduresDI±1640
Malfunction in engine coolant temperature receiver gaugeRefer to troubleshooting proceduresDI±1644
Malfunction in oil pressure receiver gaugeRefer to troubleshooting proceduresDI±1654
Malfunction in volt meterRefer to troubleshooting proceduresDI±1658
WARNING LIGHTS:
SymptomSuspected AreaSee page
Check engine warning light (MIL) does not come on.
1. ECM
2. Wire harness or connector
3. Combination meter assyDI±9
±
IN±35
Discharge warning light does not come on.
1. ECM
2. Wire harness or connector
3. Combination meter assyDI±9
±
IN±35
Brake warning light does not come on.
1. Skid control ECU
2. Wire harness or connector
3. Combination meter assyDI±895
±
IN±35
ABS warning light does not come on.
1. Skid control ECU
2. Wire harness or connector
3. Combination meter assyDI±895
±
IN±35
SRS warning light does not come on.
1. Airbag sensor assy
2. Wire harness or connector
3. Combination meter assyDI±1126
±
IN±35
Open door warning light does not come on.
1. Door courtesy light switch circuit
2. Wire harness or connector
3. Combination meter assy
4. Body ECUDI±1728
±
IN±35
IN±35
Fuel level warning light does not come on.
1. Refer to troubleshooting
2. Wire harness or connector
3. Combination meter assyDI±1640
±
IN±35
Low oil pressure warning light does not come on.
1. Low oil pressure warning switch
2. Wire harness or connector
3. Combination meter assyBE±55
±
IN±35

I27708
C5±31
C5±32
(*1) C5±30
C5±25
C5±24
C6±10
C5±23
C5±28
C5±21
C5±4
C5±29
C5±26
C6±11
C6±12
C5±22 C5±27
CPU
Supply CircuitC5±6
C5±5
C6±23
HEAD (*2)
OIL MAINT
DOOR
ILL
AIRBAG
D±BELT
FUEL WARNIG
C5±3
HI
N
LO
MAN.
BRAKE C6±16
C6±15
C6±14
C6±13
C5±1
*1: w/ Driving Position Memory *2: USA *3: Canada
TAIL (*3)
ONE STEP
DIMMER Buzzer
LCD
Speedometer
Tachometer
Fuel Gauge
Engine Coolant Temperature
Receiver Gauge
Oil Pressure Gauge
Volt Gauge DI±1622
± DIAGNOSTICSCOMBINATION METER SYSTEM
1816 Author: Date:
2005 SEQUOIA (RM1146U)
COMBINATION METER INNER CIRCUIT

Wire harness side
1
2
3
4
5
6
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
401
2
3
4
5
8 6
10
11
12
13
14
15
16
17
18
19
21
23
24
Terminal No.
Translate ECU
ECM
STA Fuse
Front Seat Inner Belt LH (Buckle Switch)
Overhead Module (Garage Door Opener)
Overhead Module (Garage Door Opener)
Washer Level Sensor
ECM
ECM (*1)
Transponder Key Computer
Body ECU
ECM
ECM
Tire Pressure Monitor ECU
Injector No. 1
Light Control Rheostat
ECM
Speed Sensor
4P OUT (Other Parts)
Fuel Sender Gauge
Oil Pressure Sender Gauge
IGN Fuse
Airbag Sensor Assembly
Memory Seat ECU and SW (*2)
Back Door ECU
Integration Control and Panel
Turn Signal Flasher Relay
Park/Neutral Position Switch
Airbag Sensor AssemblyTranslate ECU
Translate ECU
Skid Control ECU
4WD Control ECU
Alternator
Speed Sensor
Fuel Sender Gauge
Ground
Suspension Control ECU
Body ECU (*4)
Body ECU (*3)
Turn Signal Flasher Relay
Skid Control ECU
ECU±B Fuse
IGN1 Fuse Connectors:
Terminal No.
Wire harness side
C5
C64WD Control ECU
4WD Control ECU
Suspension Control ECU
Suspension Control ECU
Suspension Control ECU
*1: 4WD
*2: w/ Driving Position Memory
*3: w/ Daytime Running Light
*4: w/o Daytime Running LightPark/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch DI±1624
± DIAGNOSTICSCOMBINATION METER SYSTEM
1818 Author: Date:
2005 SEQUOIA (RM1146U)