2001 TOYOTA SEQUOIA DLC3 Ts

F19174
Combination MeterTire Pressure
Monitor ECU
Engine Room J/B I18
Ignition SW IGN1
B±O
IG2 AM2 1C11
Battery 2
1H
T17 C5GR±L
Tire Pressure
B±R
B 56
54AM2 24
6IND Instrument Panel J/B
C620
2D1
2C1 1C3
1J7
F10
Fusible Link BlockInstrument Panel J/B
W±R
W±R
B
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±873
1067 Author: Date:
2005 SEQUOIA (RM1146U)
Tire Pressure Warning Lamp Circuit
CIRCUIT DESCRIPTION
If the ECU detects trouble, the tire pressure warning lamp comes on and tire pressure monitor is cancelled
at the same time. At this time, the ECU records a DTC in memory.
Connect terminals Tc and CG of the DLC3 to make the tire pressure warning lamp blink and output the DTC.
WIRING DIAGRAM
DIDKF±01

DI±882
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1076 Author: Date:
2005 SEQUOIA (RM1146U)
3 Using hand±held tester, check the tire pressure data of each wheel.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position, and push the hand±held tester main switch ON.
(c) Select the item below in the DATA LIST, and read its value displayed on the hand±held tester.
TIRE PRESSURE:
ItemMeasurement item/
Range (Display)Normal ConditionDiagnostic Note
TIREPRESS1
ID1 tire inflation pressure/
min.: 0 kPa (0 kgfVcm2, 0 psi),
max.: 637.5 kPa (6.48 kgfVcm2,
92.2 psi)Actual tire inflation pressure±
TIREPRESS2
ID2 tire inflation pressure/
min.: 0 kPa (0 kgfVcm2, 0 psi),
max.: 637.5 kPa (6.48 kgfVcm2,
92.2 psi)Actual tire inflation pressure±
TIREPRESS3
ID3 tire inflation pressure/
min.: 0 kPa (0 kgfVcm2, 0 psi),
max.: 637.5 kPa (6.48 kgfVcm2,
92.2 psi)Actual tire inflation pressure±
TIREPRESS4
ID4 tire inflation pressure/
min.: 0 kPa (0 kgfVcm2, 0 psi),
max.: 637.5 kPa (6.48 kgfVcm2,
92.2 psi)Actual tire inflation pressure±
TIREPRESS5
ID5 tire inflation pressure/
min.: 0 kPa (0 kgfVcm2, 0 psi),
max.: 637.5 kPa (6.48 kgfVcm2,
92.2 psi)Actual tire inflation pressure±
CHECK:
Check the tire pressure data of each tire.
NEXT
4 Is any of the tire pressure data 120 kPa (1.2 kgf/cm2, 17 psi)?
No The detected DTC is for the front right wheel
transmitter.
Ye s
5 Rapidly reduce the pressure of front left wheel to 120 kPa (1.2 kgf/cm2, 17 psi).
NEXT

F19795
A20
Airbag Sensor
AssemblySub J/B No.4Tire Pressure
Monitor ECU
T5 Translate ECU
D6
DLC3TC
E4P±B P±B
TC
P±B
13
TC
TCP±B
GT17
4D5
1A94A5
4C
5 4E5 ECM
23
4B
5
CG4
J43
J/CO
15
1F
O 15A
IGA12
TC
Instrument Panel J/BP±B DI±888
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1082 Author: Date:
2005 SEQUOIA (RM1146U)
Tc and CG Terminal Circuit
CIRCUIT DESCRIPTION
DTC output mode is set by connecting terminals TC and CG of the DLC3.
The DTCs are indicated by blinking of the tire pressure warning lamp.
WIRING DIAGRAM
HINT:
When each warning lamp stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal
ground short in each ECU is suspected.
DIDKK±01

D13491
TC
D6DLC3:
F19136
T17
TC
Tire Pressure Monitor ECU:
D13491CGD6
DLC3:
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±889
1083 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
NOTICE:
It is necessary to register an ID code after replacing the tire pressure monitor valve sub±assy and/or
the tire pressure monitor ECU (see page DI±805).
1 Check harness and connector (DLC3 ± Tire pressure monitor ECU).
PREPARATION:
Disconnect the tire pressure monitor ECU T17 connector.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester connectionConditionSpecified condition
D6±13 (TC) ±
T17±12 (TC)AlwaysBelow 1 W
NG Repair or replace harness or connector.
OK
2 Check harness and connector (DLC3 ± Body ground).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester connectionConditionSpecified condition
D6±4 (CG) ±
Body groundAlwaysBelow 1 W
NG Repair or replace harness or connector.
OK

DIDLV±01
F17996
Front Speed SensorABS & VSC Actuator
(w/ Skid Control ECU)Level Warning Switch
Rear Speed Sensor Rear Speed Sensor Rotor
Front Speed
Sensor Rotor
Parking Brake SwitchStop Light Switch
Center Diff. Lock Switch *1
TRAC OFF Switch *2
Steering Angle Sensor
DLC3Brake Inhibit RelayTranslate ECU
VSC BuzzerBrake Booster
(Including Active Brake Booster
Solenoid, Delta S Sensor and Boost-
er Pedal Switch)
Master Cylinder
Pressure Sensor
Front Speed Sensor Rotor
Front Speed Sensor
Yaw Rate Sensor
(Including Deceleration Sensor)
ABS Warning Light
VSC TRAC Warning light
VSC OFF Indicator Light *
1
TRAC OFF Indicator Light *2
BRAKE Warning Light
SLIP Indicator Light
*1: Only for 4WD
*2: Only for 2WDCenter Diff. Lock
Position Switch
DI±892
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1086 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

DIDLY±01
F09750
DLC3
Ts
Tc
CG
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±897
1091 Author: Date:
2005 SEQUOIA (RM1146U)
CALIBRATION
1. ZERO POINT CALIBRATION OF MASTER CYLINDER
PRESSURE, YAW RATE AND DECELERATION SEN-
SORS
HINT:
When having replaced the master cylinder pressure, yaw rate
and deceleration sensors and/or the ECU, make sure to per-
form master cylinder pressure, yaw rate and deceleration sen-
sors' zero point calibration.
NOTICE:

While obtaining the zero point, do not vibrate the ve-
hicle by tilting, moving or shaking it and keep it in a
stationary condition. (Do not start the engine.)

Be sure to do this on a level surface (within an inclina-
tion of 1 degree).
(a) Perform master cylinder pressure, yaw rate and decelera-
tion sensors zero point calibration.
(1) Using SST, connect terminals Ts and CG of the
DLC3.
SST 09843±18040
(2) Shift the shift lever to the P position.
(3) Turn the ignition switch to the ON position.
(4) Keep the vehicle in a stationary condition on a level
surface for 4 sec. or more.
(5) Keep your foot off the brake pedal.
Do not leave 4WD vehicles in the L4 position.
(6) Press the center diff. lock (TRAC OFF) switch 3
times within 3 seconds.
(7) Check that the VSC buzzer sounds for 3 seconds.
HINT:

If the VSC buzzer does not sound, do the zero point cal-
ibration again and/or check the VSC buzzer circuit (See
page DI±1052).

If the VSC buzzer does not sound, check for yaw rate and
deceleration sensor failure (See page DI±911).
(8) Turn the ignition switch OFF.
(9) Disconnect terminals Ts and CG of the DLC3.
(b) Perform steering angle sensor zero point calibration.
This calibration is carried out automatically by following
procedures below:
(1) Make sure the system is not in sensor check mode.
(2) Calibrate the steering angle sensor by driving the
vehicle in a straight line at more than 7 MPH (12
km/h) for 5 seconds.

DIDLZ±01
F09750
DLC3Ts
CG
BR3904
0.13 sec. 0.13 sec.
ON
OFF
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±899
1093 Author: Date:
2005 SEQUOIA (RM1146U)
TEST MODE PROCEDURE
1. When not using the hand±held tester:
SENSOR CHECK (TEST MODE)
NOTICE:
When having replaced the master cylinder pressure, yaw
rate and deceleration sensors and/or the ECU, perform
zero point calibration of the master cylinder pressure, yaw
rate and deceleration sensors (See page DI±897).
HINT:
If the ignition switch is turned from the ON to the ACC or LOCK
position in test mode, test mode DTCs will be erased.
(a) Procedures for test mode:
(1) Turn the ignition switch OFF.
(2) Check that the shift lever is in the P position, and
turn the steering wheel to the neutral position.
(3) Using SST, connect terminals Ts and CG of the
DLC3.
SST 09843±18040
(4) Start the engine.
(5) Check that the ABS and VSC TRAC warning lights
blink.
HINT:
If the ABS and VSC TRAC warning lights do not blink, inspect
the ABS warning light circuit, VSC TRAC warning light circuit
and Ts terminal circuit.
(6) Keep the vehicle in a stationary condition on a level
surface for 4 sec. or more.
ABS warning light circuitDI±1021 or DI±1025
VSC TRAC warning light circuitDI±1027 or DI±1031
Ts terminal circuitDI±1057

F09750
CG TcDLC3
BR3893
Trouble Code (Example Code 72, 76)
ON
OFF
4 sec. 1.5 sec.
Repeat 2.5 sec.
0.5 sec. 0.5 sec. 0.5 sec. 0.5 sec.7726
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±901
1095 Author: Date:
2005 SEQUOIA (RM1146U)
(f) Read the DTC.
(1) Using SST, connect terminals Tc and CG of the
DLC3.
SST 09843±18040
(2) Read the number of blinks of the warning light.
HINT:

See the list of DTC (step 3).

If all sensors are normal, a normal system code is output
(A cycle of 0.25 sec. ON and 0.25 sec. OFF is repeated).

If 2 or more malfunctions are indicated at the same time,
the codes will be displayed in ascending order.
(3) After doing the check, disconnect terminals Ts and
CG, Tc and CG of the DLC3, and turn the ignition
switch OFF.
SST 09843±18040