2001 TOYOTA SEQUOIA VSC system

DI±1044
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1238 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check SLIP indicator light.
See combination meter troubleshooting on page DI±1614.
NG Repair or replace combination meter
(See page DI±1610).
OK
5 Is DTC output?
Check DTC (Translate ECU and CAN communication system) on page DI±911.
NG Repair circuit indicated by output code
(See page DI±921).
OK
6 Check for open and short circuit in harness and connector between translate
ECU and SLIP indicator light (See page IN±35).
NG Repair or replace harness or connector.
OK
Check and replace translate ECU.

± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1045
1239 Author: Date:
2005 SEQUOIA (RM1146U)
SLIP Indicator Light Circuit (Does not light up)
CIRCUIT DESCRIPTION
See page DI±1041.
WIRING DIAGRAM
See page DI±1041.
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 3 when not using the
hand±held tester.
1 Check operation of the SLIP indicator light.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position and push the hand±held tester main switch ON.
(c) Select ACTIVE TEST mode on the hand±held tester.
CHECK:
Check that ºONº and ºOFFº of the SLIP indicator light can be shown on the combination meter with the hand±
held tester.
ItemVehicle Condition / Test DetailsDiagnostic Note
SLIP INDI LIGHTTurns SLIP indicator light ON / OFFObserve combination me-
ter
OK:
SLIP indicator operates.
NG Go to step 3.
OK
DIDMP±01

DI±1046
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1240 Author: Date:
2005 SEQUOIA (RM1146U)
2 Replace the translate ECU and check if the trouble occurs again.
PREPARATION:
(a) Clear the DTC (See page DI±911).
(b) Turn the ignition switch OFF.
CHECK:
Turn the ignition switch to the ON position, and check if the same DTC still remains in the memory.
RESULT:
DTC is outputA
DTC is not outputB
B END.
A
Check and replace skid control ECU
(See page BR±52).
NOTICE:
When replacing the skid control ECU, perform the zero point calibration (See page DI±897).
3 Check harness and connector between translate ECU and skid control ECU
(CAN1 circuit).
NG Repair or replace parking brake switch circuit
(CAN1 circuit).
OK
4 Check harness and connector between translate ECU and combination meter
(See page IN±35).
NG Repair or replace harness or connector.
OK

± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1047
1241 Author: Date:
2005 SEQUOIA (RM1146U)
5 Check SLIP indicator light.
See combination meter troubleshooting on page DI±1614.
NG Repair combination meter assembly
(See page DI±1610).
OK
Check and replace skid control ECU
(See page BR±52).
NOTICE:
When replacing the skid control ECU, perform the zero point calibration (See page DI±897).

DI±1048
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1242 Author: Date:
2005 SEQUOIA (RM1146U)
VSC OFF *1 (TRAC OFF)*2 Indicator Light, Center Diff. Lock *1
(TRAC OFF)*2 Switch Circuit
*1: Only for 4WD
*
2: Only for 2WD
CIRCUIT DESCRIPTION
This is the VSC (TRAC) control main switch. When the center diff. lock (TRAC OFF) switch is pushed on,
VSC (TRAC) indicator goes off and the VSC OFF (TRAC OFF) indicator comes on. Turn the ignition switch
OFF, and check that the VSC (TRAC) indicator comes on when turning the ignition switch to the ON position
again.
Pressing the center diff. lock switch in 2WD mode does not deactivate VSC control. *
1
DI948±04

F19780
ABS & VSC Actuator
(Skid Control ECU)
Translate ECU
CANH
CANL
IG1 VSC± VSC+
IG17
T5
11
T5
1
T56
S1
2
S1
13
S1 7
IL2
6
IL2
1
IL2 A
J38
A
J37 A
J37
8
3C8
3A L
W
B±RL
W
B±R
B±R
B±R B±R
B±R Instrument Panel J/B
4
1C
2
1C
3
1C
6
1C4
11
1H
7
1J
1
1L 1F ECU±IG
IGN1
AM1
21 AM1
AM2IG1
IG2 I18
Ignition SW
B±Y
B±R W±L
W±R
W±LB±O
W±R
W 12
56C6
Combination
Meter
VSC OFF
(4WD)
TRAC OFF
(2WD)
24
2
R±G W±R W
Engine Room J/B
1
2D1
2C AM2 F10 Fusible
Link Block
B 8
54 ALT
R±G 38
T5
26
T5
31
T5
40
T5 WT
CSW
EXI2
GND
(4WD)
Y±G
(4WD)
L±W
Y±B L±WSub J/B No.4
8
4B
7
4B7
4A8
4A16
F23
4
F23DL
PI
B
BatteryA
AJ43
J/C
IGJ18
J/C
IG A
A W±B W±B
O
OW±B
W±B 17
IL1
9
IL132
S11
S1GND1
GND2 Sub J/B No.3
4WD Control ECU J/C (*) CAN1 Circuit
(*)
(*)(*) (*)
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1049
1243 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

F13991
GNDCSW*1
Center Integration Panel Assembly
CSW
*2
C3C6
DI±1050
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1244 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 2 when not using the
hand±held tester.
1 Check operation of the VSC OFF (TRAC OFF) indicator light.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position and push the hand±held tester main switch ON.
(c) Select ACTIVE TEST mode on the hand±held tester.
CHECK:
Check that ºONº and ºOFFº of the VSC OFF (TRAC OFF) indicator light can be shown on the combination
meter with the hand±held tester.
ItemVehicle Condition / Test DetailsDiagnostic Note
VSC OFF (TRAC OFF)Turns VSC OFF (TRAC OFF) indicator ON / OFFObserve combination me-
ter
OK:
VSC OFF (TRAC OFF) indicator light comes on.
NG Go to step 4.
OK
2 Check center diff. lock (TRAC OFF) switch.
PREPARATION:
Remove center integration panel assembly (See page
BO±85).
CHECK:
Measure the resistance between terminals CSW and GND of
the center diff. lock
*1
(TRAC OFF *2) switch when the center diff.
lock
*1 (TRAC OFF *2) switch is ON and OFF.
*1
: Only for 4WD
*2 : Only for 2WD
OK:
Center diff. lock (TRAC OFF) switchResistance
Press continuouslyContinuity
Release1MW or higher
NG Replace center diff. lock (TRAC OFF) switch.
OK

± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1051
1245 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check for open and short circuit in harness and connector between terminal
CSW of the translate ECU and center diff. lock (TRAC OFF) switch and body
ground (See page IN±35).
NG Repair or replace harness or connector.
OK
4 Check VSC OFF (TRAC OFF) indicator light.
See combination meter troubleshooting on page DI±1614.
NG Repair or replace combination meter
(See page DI±1610).
OK
5 Check for open and short circuit in harness and connector between terminal WT
of the translate ECU and VSC OFF (TRAC OFF) indicator light (See page
IN±35).
NG Repair or replace harness or connector.
OK
Check and replace translate ECU