2001 TOYOTA SEQUOIA change time

B17386
Housing
Solid Electrolyte
(Zirconia Element)
Platinum Electrode
Heater
Coating (Ceramic)
Exhaust Gas CoverIdeal Air±Fuel Mixture
Output Voltage
Richer ± Air Fuel Ratio ± Leaner
Atmospheric Air
A21040
Reference(Bank 1 Sensor 1 System Drawing) :
ECM
EFI Relay
EFI Fuse No. 1 From
Battery
GroundOX1A
MREL HT1A
Duty
Control Heater
Sensor Heated Oxygen Sensor
EFI Fuse No. 2
E2 DI±94
± DIAGNOSTICSENGINE
288 Author: Date:
2005 SEQUOIA (RM1146U)
CIRCUIT DESCRIPTION
To obtain a high purification rate for the CO, HC and NOx components of the exhaust gas, a three±way cata-
lytic converter is used, but for the most efficient use of the three±way catalytic converter, the air±fuel ratio
must be precisely controlled so that it is always close to the stoichiometric air±fuel ratio.
The heated oxygen sensor has the characteristic which its output voltage changes suddenly in the vicinity
of the stoichiometric air±fuel ratio. This characteristic is used to detect the oxygen concentration in the ex-
haust gas and provide the ECM with feedback to control the air±fuel ratio.
When the air±fuel ratio becomes LEAN, the oxygen concentration in the exhaust increases and the heated
oxygen sensor informs the ECM of the LEAN condition (low voltage, i.e. less than 0.45 V).
When the air±fuel ratio is RICHER than the stoichiometric air±fuel ratio, the oxygen concentration in the ex-
haust gas is reduced and the heated oxygen sensor informs the ECM of the RICH condition (high voltage,
i.e. more than 0.45 V). The ECM judges by the voltage output from the heated oxygen sensor whether the
air±fuel ratio is RICH or LEAN and controls the injection time accordingly. However, if malfunction of the
heated oxygen sensor causes output of abnormal voltage, this disables the ECM for performing an accurate
air±fuel ratio control. The heated oxygen sensors include a heater which heats the zirconia element. The
heater is controlled by the ECM. When the intake air volume is low (the temperature of the exhaust gas is
low) current flows to the heater to heat the sensor for accurate oxygen concentration detection.
HINT:
The ECM provides a pulse width modulated control circuit to adjust current through the heater. The heated
oxygen sensor heater circuit uses a relay on the B+ side of the circuit.

± DIAGNOSTICSENGINE
DI±105
299 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Connect hand±held tester, and read value of mass air flow rate.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and push the hand±held tester main switch ON.
(c) Start the engine.
(d) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA
LIST / ALL / MAF.
CHECK:
Read the mass air flow rate on the hand±held tester.
RESULT:
Air Flow Rate (gm/s)Proceed to
0.0A
271.0 or moreB
Between 1 and 270.0 (*1)C
*1: The value must change when the throttle valve is opened or closed.
B Go to step 6.
C Check for intermittent problems
(See page DI±11).
A

DI±126
± DIAGNOSTICSENGINE
320 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Case 1 (When temperature is fixed between 35C (95F) and 60C (140F)):
Cumulative idle off period250 sec.±
Speed increase 30 km/h (18.6 mph) or
more10 times±
Engine coolant temperature35C (95F)60C (140F)
Intake air temperature±6.7C (20F)±
Case 2 (When temperature is fixed at 60C (140F) or more):
Engine coolant temperature at engine
start60C (140F)±
Intake air temperature±6.7C (20F)±
Stop and goOnce or more (Stop for 20 sec. or more and accelerate to more than 70 km/h (43.5 mph)
with in 40 sec.)
Steady driving and stop *Once or more
*: Vehicle is driven by 65 km/h (40.4 mph) or more for 30 sec. or more and the vehicle speed reaches 70
km/h (43.5 mph). The vehicle is decelerated from 65 km/h (40.4 mph) to 3 km/h (1.86 mph) or less within
35 sec. and stopped for 10 sec.
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Case1 (When temperature is fixed between 35C (95F) and 60C (140F)):
Change of engine coolant temperature valueLess than 3C (5.4F)
Case2 (When temperature is fixed at 60C (140F) or more):
Change of engine coolant temperature value1C (1.8F) or less
COMPONENT OPERATING RANGE
Standard Value
Engine coolant temperature changes with the actual engine coolant temperature.
INSPECTION PROCEDURE
HINT:

If DTC P0115, P0116, P0117, P0118 and P0125 are output simultaneously, ECT sensor circuit may
be open or shorted. Perform the troubleshooting of DTC P0115, P0117 or P0118 first.

Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the
vehicle was running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or
rich, as well as other data from the time when a malfunction occurred.
Replace engine coolant temperature sensor.

A23661
Vehicle Speed
(64 km/h and 113 km/h)Between
40 mph and 70 mph
Idling
Ignition Switch OFF
10 minutes
Time Warm up
(Note: Even if vehicle stops during driving pattern, test can be resumed)NOTICE:
This test will not be completed
if the vehicle is driven under
absolutely constant speed
conditions such as with cruise
control activated. (h)
(g)
MISFIRE MON ..................... AVAILREADINESS TESTS
CAT EVAL ......................... INCMPL
HTD CAT EVAL ...................... N/A
EVAP EVAL ....................... INCMPL
2nd AIR EVAL .......................... N/A
A/C EVAL ................................ N/A
O2S EVAL ........................ INCMPL
O2S HTR EVAL .................. INCMPL
EGR EVAL ...............................N/A COMP MON ........................ AVAIL FUEL SYS MON ................... AVAIL
A76855
A23660
DI±154
± DIAGNOSTICSENGINE
348 Author: Date:
2005 SEQUOIA (RM1146U)
CONFIRMATION DRIVING PATTER
HINT:

This confirmation driving pattern is used in steps 5, 8 and 11 of the following diagnostic troubleshooting
procedure when using either a hand±held tester.

Performing this confirmation pattern will activate the Heated Oxygen (HO2) sensor monitor. (The cata-
lyst monitor is performed simultaneously.) This is very useful for verifying the completion of a repair.
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the tester or scan tool ON.
(d) Clear DTCs (where set) (see page DI±43).
(e) If using a hand±held tester, select the following menu
items: DIAGNOSIS / CARB OBD II / READINESS
TESTS.
(f) Check that O2S EVAL is INCMPL (incomplete).
(g) Start the engine and warm it up.
(h) Drive the vehicle at between 40 mph and 70 mph (64 km/h
and 113 km/h) for at least 10 minutes.
(i) Note the state of the Readiness Tests items. Those items
will change to COMPL (complete) as O2S EVAL monitor
operates.
(j) On the tester, select the following menu items: DIAGNO-
SIS / ENHANCED OBD II / DTC INFO / PENDING
CODES and check if any DTCs (any pending DTCs) are
set.
HINT:
If O2S EVAL does not change to COMPL, and any pending
DTCs fail to set, extend the driving time.

± DIAGNOSTICSENGINE
DI±165
359 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0171 System too Lean (Bank 1)
DTC P0172 System too Rich (Bank 1)
DTC P0174 System too Lean (Bank 2)
DTC P0175 System too Rich (Bank 2)
CIRCUIT DESCRIPTION
The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim con-
sists of both the short±term and long±term fuel trims.
The short±term fuel trim is fuel compensation that is used to constantly maintain the air±fuel ratio at stoichio-
metric levels. The signal from the Air±Fuel Ratio (A/F) sensor indicates whether the air±fuel ratio is rich or
lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air±fuel
ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause
short±term fuel trim to vary from the central value. The long±term fuel trim, which controls overall fuel com-
pensation, compensates for long±term deviations in the fuel trim from the central value caused by the short±
term fuel trim compensation.
If both the short±term and long±term fuel trims are lean or rich beyond predetermined values, it is interpreted
as a malfunction, and the ECM illuminates the MIL and sets a DTC.
DIDFQ±01

DI±254
± DIAGNOSTICSENGINE
448 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Are there any other codes (besides DTC P0420 or P0430) being output?
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using the hand±held tester.
RESULT:
Display (DTC Output)Proceed to
ºP0420 and/or P0430ºA
ºP0420 or P0430º and other DTCsB
HINT:
If any other codes besides ºP0420 and/or P0430º are output, perform the troubleshooting for those DTCs
first.
B Go to relevant DTC chart (See page DI±58).
A
2 Check A/F sensor (bank 1, 2 sensor 1).
(a) Connect the hand±held tester to the DLC3.
(b) Start the engine and turn the tester ON.
(c) Warm up the engine with the engine speed at 2,500 rpm for approximately 90 seconds.
(d) On the tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST /
A/F CONTROL.
(e) Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT or LEFT
button to change the fuel injection volume).
(f) Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2) displayed on the
tester.
HINT:
The A/F CONTROL operation lowers the fuel injection volume by 12.5 % or increases the injection
volume by 25 %.
Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

DI±254
± DIAGNOSTICSENGINE
448 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Are there any other codes (besides DTC P0420 or P0430) being output?
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using the hand±held tester.
RESULT:
Display (DTC Output)Proceed to
ºP0420 and/or P0430ºA
ºP0420 or P0430º and other DTCsB
HINT:
If any other codes besides ºP0420 and/or P0430º are output, perform the troubleshooting for those DTCs
first.
B Go to relevant DTC chart (See page DI±58).
A
2 Check A/F sensor (bank 1, 2 sensor 1).
(a) Connect the hand±held tester to the DLC3.
(b) Start the engine and turn the tester ON.
(c) Warm up the engine with the engine speed at 2,500 rpm for approximately 90 seconds.
(d) On the tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST /
A/F CONTROL.
(e) Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT or LEFT
button to change the fuel injection volume).
(f) Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2) displayed on the
tester.
HINT:
The A/F CONTROL operation lowers the fuel injection volume by 12.5 % or increases the injection
volume by 25 %.
Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

A23484
Purge VSV
Vent Valve
Vacuum Pump
EVAP Pressure
Positive
Leak Pressure
sec NegativeONON
Sequence
TimeA
10
sec60
Within 15 minutesON
First 0.02 inch
BCD
OK
Malfunction
ON: Open
OFF: Closed
OFF: Vent ON: Closed
10
Standard
sec60
E EVAP Pressure when Purge VSV Stuck Closed:
A23485
EVAP Pressure
During Purge Flow Monitor:
VSV
EVAP
PressureOpen
1st
Monitor2nd
Monitor
ON (closed)
Purge
Valve Vent
OK
OK
Malfunction
0.1 kPa
0.5 kPa
DI±260
± DIAGNOSTICSENGINE
454 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Purge VSV stuck closed
In operation D, the pressure sensor measures the EVAP system pressure. The pressure measurement for
purge VSV monitor is begun when the purge VSV is turned ON (open) after the EVAP leak check. When
the measured pressure indicates an increase of 0.3 kPa (2.25 mmHg) or more, the purge VSV is functioning
normally. If the pressure does not increase, the ECM interprets this as the purge VSV being stuck closed.
The ECM illuminates the MIL and sets the DTC (2 trip detection logic).
2. PURGE FLOW MONITOR
The purge flow monitor consists of the two step monitors. The
1st monitor is conducted every time and the 2nd monitor is acti-
vated if necessary.

The 1st monitor
While the engine is running and the purge VSV
(Vacuum Switching Valve) is ON (open), the ECM
monitors the purge flow by measuring the EVAP
pressure change. If negative pressure is not
created, the ECM begins the 2nd monitor.

The 2nd monitor
The vent valve is turned ON (closed) and the EVAP
pressure is then measured. If the variation in the
pressure is less than 0.5 kPa (3.75 mmHg), the
ECM interprets this as the purge VSV being stuck
closed, and illuminates the MIL and sets DTC
P0441 (2 trip detection logic).
Atmospheric pressure check:
In order to ensure reliable malfunction detection, the variation
between the atmospheric pressures, before and after conduc-
tion of the purge flow monitor, is measured by the ECM.