2001 TOYOTA SEQUOIA warning

F18069
DI±940
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1134 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check brake fluid level warning switch.
PREPARATION:
Disconnect the brake fluid level warning switch connector.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSwitch ConditionSpecified Condition
(B2±1) ± (B2±2)Float UP10 kW or more
(No continuity)
(B2±1) ± (B2±2)Float DOWN1 W or less (Continuity)
NG Replace brake reservoir tank.
OK
5 Check for open and short circuit in harness and connector between brake fluid
level warning switch and translate ECU (See page IN±35).
NG Repair or replace harness or connector.
OK

F19197
S1 ABS & VSC Actuator
(Skid Control ECU)Translate
ECU
CANH
CANL6
2L
WL
W 7
IL2
6
IL27
T5
11
T5VSC+
VSC±
IG1 1
T5 B±R
J37 J37J/C
B±R
B±R8
3C 8
3A
I18
Ignition SW
4
1F4
1C
1L6
1C ECU±IG
AM1
AM1 IG1
B±Y
2
W±L W
ALT
Battery24
T5
40
T5LVL2
GND 23
IA1 9
IA5Y±L Y±L W±B O
A
O A
AB1
Brake Fluid
Level Warning SW
J43
J/C
IG 1Sub J/B No.3
Instrument Panel J/B
8
5F10
Fusible Link Block
B1
1 2
2A
A
1
(*) CAN1 Circuit (*)(*)
(*)
(*) DI±1002
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1196 Author: Date:
2005 SEQUOIA (RM1146U)
DTC 58 Malfunction of Brake Fluid Level Warning
Switch
CIRCUIT DESCRIPTION
The brake fluid level warning switch sends the appropriate signal to the translate ECU.
This signal indicates a drop in brake fluid level.
DTC No.DTC Detecting ConditionTrouble Area
58

Brake fluid level warning switch connector is disconnected
for 1 sec. or more.

Brake fluid level warning switch is ON for 30 sec. or more.
Brake fluid level warning switch circuit

Brake fluid level warning switch

Brake fluid reservoir level

Translate ECU
WIRING DIAGRAM
DIDMI±01

F18069
P2
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1003
1197 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check the DTC of the VSC (See page DI±911).
CHECK:
Check skid control ECU DTC.
RESULT:
DTC is not outputA
DTC (C1202 / 52) is outputB
B Repair circuit indicated by the output code
(See page DI±921).
A
2 Check brake fluid level warning switch.
PREPARATION:
Disconnect the brake fluid level warning switch connector.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSwitch ConditionSpecified Condition
(B2±1) ± (B2±2)Float UP10 kW or more
(No continuity)
(B2±1) ± (B2±2)Float DOWN1 W or less (Continuity)
NG Replace brake fluid level warning switch.
OK
3 Check for open and short circuit in harness and connector between brake fluid
level warning switch and translate ECU (See page IN±35).
NG Repair or replace harness or connector.
OK

± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1013
1207 Author: Date:
2005 SEQUOIA (RM1146U)
DTC Normal Code Malfunction in Translate ECU
CIRCUIT DESCRIPTION
If any trouble occurs in the engine control system, the skid control ECU prohibits ABS & VSC control.
DTC No.DTC Detecting ConditionTrouble Area
Normal Code
Conditions 1., 2. or 3. continue for 5 sec. or more:
1. Engine malfunction signal is sent from ECM.
2. Shift malfunction signal is sent from ECM.
3. The shift position is other than P and N, and P range
input voltage is 8 V or more.

ECM circuit

ECM

Brake fluid level

Brake fluid level warning switch circuit

Steering angle sensor

Translate ECU

Skid control ECU

Vehicle CAN

VSC+, VSC± circuit (CAN1 communication system)
INSPECTION PROCEDURE
1 Is DTC output for ECM?
Check DTC on page DI±43.
YES Repair engine control system according to the
output code (See page DI±58).
NO
2 Check the DTC of the ABS and VSC (See page DI±911).
CHECK:
Check skid control ECU DTC.
RESULT:
Only DTC ºC1203/53º of the VSC system is outputA
Except DTC ºC1203/53º of the VSC system are outputB
B Repair ABS and VSC control system according
to the code output (See page DI±921).
A
DI6OF±12

± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1015
1209 Author: Date:
2005 SEQUOIA (RM1146U)
DTC Non ± Code Translate ECU malfunction
CIRCUIT DESCRIPTION
Translate ECU DTCs can be read by blinks of the brake warning light (see page DI±911).
DTC No.DTC Detecting ConditionTrouble Area
Non ± code*Translate ECU internal malfunction is detected.

Brake warning light circuit

Tc terminal circuit

Translate ECU
*: Neither the normal system code nor a trouble code is output.
INSPECTION PROCEDURE
1 Check the BRAKE warning light circuit (See page DI±1033).
OK:
BRAKE warning light circuit is normal.
NG Repair or replace the BRAKE warning light cir-
cuit.
OK
2 Check the Tc terminal circuit (See page DI±1055).
OK:
Tc terminal circuit is normal.
NG Repair or replace the Tc terminal circuit.
OK
Check and replace the translate ECU.
DI942±03

DI±1016
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1210 Author: Date:
2005 SEQUOIA (RM1146U)
DTC Always ON* Malfunction in Skid Control ECU
*: ABS warning light
When reading DTCs by SST (CHECK WIRE), if the ABS warning light remains ON, troubleshoot by following
the inspection flow.
CIRCUIT DESCRIPTION
DTC No.DTC Detecting ConditionTrouble Area
Always ON
When any of the following conditions are detected:
1. Malfunction in ECU internal circuit is identified.
2. ECU power source voltage is too high.

Battery

Charging system

Power source circuit

ABS warning light circuit

Skid control ECU
HINT:
There is a possibility that the hand±held tester cannot be used when the ECU is abnormal.
DI943±03

DI±1020
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1214 Author: Date:
2005 SEQUOIA (RM1146U)
6 Check operation of the ABS warning light.
When using the hand±held tester:
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position and push the hand±held tester main switch ON.
(c) Select ACTIVE TEST mode on the hand±held tester.
CHECK:
Check that ºONº and ºOFFº of the ABS warning light can be shown on the combination meter by the hand±
held tester.
ItemVehicle Condition / Test DetailsDiagnostic Note
ABS WARN LIGHTTurns ABS warning light ON / OFFObserve combination me-
ter
OK:
ABS warning light operates.
When not using the hand±held tester:
PREPARATION:
(a) Turn the ignition switch OFF.
(b) Disconnect the connector from the skid control ECU.
(c) Turn the ignition switch to the ON position.
CHECK:
Check the ABS warning light comes on.
OK:
ABS warning light comes on.
OK Replace skid control ECU
(See page BR±52).
NOTICE:
When replacing the skid control ECU, perform the zero
point calibration (See page DI±897).
NG
7 Check ABS warning light.
See combination meter troubleshooting on page DI±1614.
NG Repair combination meter assembly
(See page DI±1610).
OK
Check for short circuit in harness and connector between ABS warning light and skid control
ECU (See page IN±35).

± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1021
1215 Author: Date:
2005 SEQUOIA (RM1146U)
ABS Warning Light Circuit (Remains ON)
CIRCUIT DESCRIPTION
If the ECU detects trouble, it turns on the ABS warning light and prohibits ABS control. At this time, the ECU
records a DTC in memory.
Connect terminals Tc and CG of the DLC3 to make the ABS warning light blink and indicate the DTC.
DI944±04