2001 TOYOTA SEQUOIA fuel

± DIAGNOSTICSENGINE
DI±297
491 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
P0604:
RAMRAM check failure
P0606:
Either of the following conditions is metCondition 1 or 2
1. Difference between TP of main CPU and TP of sub CPU0.3 V or more
2. Difference between APP of main CPU and APP of sub
CPU0.3 V or more
P0607:
Either of the following conditions is metCondition 1 or 2
1. All of the following conditions are metCondition (a), (b) and (c)
(a) CPU reset1 time or more
(b) Difference between TP and APP learned0.4 V or more
(c) Electronic throttle actuatorOFF
2. CPU reset2 times or more
P0657:
ECTS power supply when ignition switch OFF to ON7 V or more
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
Replace ECM (See page SF±80).

DI±300
± DIAGNOSTICSENGINE
494 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Connect hand±held tester, and check STA signal.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA
LIST / ALL / STARTER SIG.
CHECK:
Read the STA signal on the hand±held tester while the starter operates.
OK:
Standard:
Ignition Switch PositionONSTART
STARTER SIGOFFON
OK Go to step 5.
NG
2 Check park/neutral position switch (See page DI±576).
NG Replace park/neutral position switch.
Go to next step 5 after the replacement.
OK
3 Check ignition switch (See page BE±24).
NG Replace ignition switch.
Go the next step 5 after the replacement.
OK

B17445
Wire Harness Side:
Camshaft Position Sensor
A23559
2 V / DIV
GND
Crank Angle
120°120° 180°
180°
60°60°
200 ms /DIV
B17414
E6ECM Connector
G2+
G2±
DI±306
± DIAGNOSTICSENGINE
500 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using hand±held tester. Because freeze frame records the engine conditions when
the malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle was run-
ning or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc. at the time of the
malfunction.
1 Check voltage of camshaft position sensor power source circuit.
PREPARATION:
(a) Disconnect the Camshaft position sensor connector.
(b) Turn the ignition switch to ON.
CHECK:
Measure the voltage between terminal 3 of the camshaft posi-
tion sensor connector and body ground.
OK:
Standard: 4.5 to 5.5 V
NG Repair or replace harness or connector.
OK
2 Check camshaft position sensor signal.
PREPARATION:
Start the engine.
CHECK:
Check the waveform between the G2+ (E6±19) and G2±
(E6±29) of the ECM connector.
OK:
Standard: Correct waveform is as shown.
OK Replace ECM (See page IN±35).
NG

A16555
AIR INJ CHECK
AIR PUMP............................ON
EASV ............................OPEN
ASV1. .............................OPEN
ASV2...............................OPEN
A/F BANK1......................19.05
A/F BANK2........................14.5
PRESSURE....................17 kPa
PULSATION..............25.39 kPa
AI STATUS...........................OK
Remaining Time 05 sec.
Press [EXIT] to quit
± DIAGNOSTICSENGINE
DI±325
519 Author: Date:
2005 SEQUOIA (RM1146U)
7 Check air switching valve No.2 operation.
PREPARATION:
(a) Start the engine and warm it up.
(b) Turn the ignition switch to OFF.
(c) Connect the hand±held tester to the DLC3.
(d) Start the engine and push the hand±held tester main
switch ON.
CHECK:
(a) Select the following menu items: DIAGNOSIS/EN-
HANCED OBD II/SYSTEM CHECK/ AIR INJ CHECK/
MANUAL OPERATION/OPERATION 5 and 6
HINT:
OPERATION 5: AP:ON, EASV:OPEN, ASV1:OPEN,
ASV2:CLOSE
OPERATION 6: AP:ON, EASV:OPEN, ASV1:CLOSE,
ASV2:OPEN
NOTICE:
This test only allows technicians to operate the AI system
for 5 seconds. Furthermore, the test can be performed 4
times a trip. If the test is repeated, intervals of at least 30
seconds are required between tests.
While the AI system operation using the hand±held tester
is prohibited, the tester displays the prohibition (WAIT or
ERROR). If the ERROR (AI STATUS NG) is displayed on the
tester, stop the engine for 10 minutes and then try again..
(b) Read value of the A/F BANK1 and BANK2 on the hand±
held tester.
RESULT:
Air switching valve No.2 operationAir±fuel ratio
Open18 or more
CloseApproximately 14.5
HINT:

When the ASV No.2 operates normally, the A/F value is 18 or more when the valve is open, and approx-
imately 14.5 when the valve is closed.

Perform the following procedures only on the bank of which the valve is not close.
NEXT

A16555
AIR INJ CHECK
AIR PUMP............................ON
EASV ............................OPEN
ASV1. .............................OPEN
ASV2...............................OPEN
A/F BANK1.......................19.05
A/F BANK2.........................14.5
PRESSURE....................17 kPa
PULSATION..............25.39 kPa
AI STATUS...........................OK
Remaining Time 05 sec.
Press [EXIT] to quit
DI±336
± DIAGNOSTICSENGINE
530 Author: Date:
2005 SEQUOIA (RM1146U)
6 Check air switching valve No.2 operation.
PREPARATION:
(a) Start the engine and warm it up.
(b) Turn the ignition switch to OFF.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to ON and push the hand±held
tester main switch ON.
CHECK:
(a) Select the following menu items: DIAGNOSIS/EN-
HANCED OBD II/SYSTEM CHECK/ AIR INJ CHECK/
MANUAL OPERATION/OPERATION 5 and 6
HINT:
OPERATION 5: AP:ON, EASV:OPEN, ASV1:OPEN,
ASV2:CLOSE
OPERATION 6: AP:ON, EASV:OPEN, ASV1:CLOSE,
ASV2:OPEN
NOTICE:
This test only allows technicians to operate the AI system
for 5 seconds. Furthermore, the test can be performed 4
times a trip. If the test is repeated, intervals of at least 30
seconds are required between tests.
While the AI system operation using the hand±held tester
is prohibited, the tester displays the prohibition (WAIT or
ERROR). If the ERROR (AI STATUS NG) is displayed on the
tester, stop the engine for 10 minutes and then try again..
(b) Read value of the A/F BANK1 and BANK2 on the hand±
held tester.
RESULT:
Air switching valve No.2 operationAir±fuel ratio
Open18 or more
CloseApproximately 14.5
HINT:

When the ASV No.2 operates normally, the A/F value is 18 or more when the valve is open, and approx-
imately 14.5 when the valve is closed.

Perform the following procedures only on the bank of which the valve is not open.
NEXT

DI±348
± DIAGNOSTICSENGINE
542 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:

Using the AIR INJ CHECK operation of the SYSTEM CHECK provided in the hand±held tester func-
tion, conditions for air±fuel ratio and pressure in the secondary air injection system passage can be
checked while the secondary air injection system operating. It helps technicians to troubleshoot the
system when it malfunctioning.

Read freeze frame data using a hand±held tester. Freeze frame data record the engine condition when
malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle
was moving or stationary, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, and
other data, from the time the malfunction occurred.
1 Check any other DTCs output (In addition to air injection system DTCs).
PREPARATION:
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
CHECK:
(a) Read DTCs.
RESULT:
Display (DTC Output)Proceed To
P1613A
P1613 and other DTCsB
HINT:
If any DTCs other than P1613 are output, troubleshoot those DTCs first.
B Go to DTC chart (See page DI±58).
A

DI±354
± DIAGNOSTICSENGINE
548 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P2102 Throttle Actuator Control Motor Circuit Low
DTC P2103 Throttle Actuator Control Motor Circuit High
CIRCUIT DESCRIPTION
The throttle motor is operated by the ECM. It opens and closes the throttle valve.
The opening angle of the throttle valve is detected by the throttle position sensor which is mounted on the
throttle body. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to
control the throttle motor and monitor the throttle opening angle as the ECM responds to driver inputs.
HINT:
This Electrical Throttle Control System (ETCS) does not use a throttle cable.
DTC No.DTC Detection ConditionTrouble Area
P2102
Conditions (a) and (b) continue for 2.0 seconds:
(1 trip detection logic)
(a) Throttle control motor output duty 80 % or more
(b) Throttle control motor current less than 0.5 A or less
Open in throttle control motor and sensor circuit

Throttle control motor and sensor

ECM
P2103
Either of the following condition is met.
(1 trip detection logic)
(a) Throttle control motor current 10 A or more (0.1 sec)
(b) Throttle control motor current 7 A or more (0.6 sec.)
Short in throttle control motor and sensor circuit

Throttle control motor and sensor

Throttle valve

Throttle body

ECM
MONITOR DESCRIPTION
The ECM monitors the current through the electronic throttle motor and detects malfunctions or open circuit
in the throttle motor based on the voltage of the current. When the current deviates from the standard, the
ECM concludes that there is a fault in the throttle motor.
Or, if the throttle valve is not functioning properly (for example, stuck ON), the ECM concludes that there is
a fault, turns on the MIL and sets a DTC is set.
Example:
When the current is more than 10 A. Or the current is less than 0.5 A when the motor driving duty ratio is
exceeding 80%. The ECM concludes that the current is out of range, turns on the MIL and a DTC is set.
FAIL SAFE
If the ETCS (Electronic Throttle Control System) has a malfunction, the ECM cuts off current to the throttle
control motor. The throttle control valve returns to a predetermined opening angle (approximately 16°) by
the force of the return spring. The ECM then adjusts the engine output by controlling the fuel infection (inter-
mittent fuel±cut) and ignition timing in accordance with the accelerator pedal opening angle to enable the
vehicle to continue at a minimum speed.
If the accelerator pedal is depressed firmly and slowly, the vehicle can be driven slowly.
If a ºpassº condition is detected and then the ignition switch is turned OFF, the fail±safe operation will stop
and the system will return to normal condition.
DICF9±02

A21034
T14
Component Side:
M+M± Throttle Control Motor and Sensor
DI±356
± DIAGNOSTICSENGINE
550 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check throttle control motor.
PREPARATION:
Disconnect the throttle control motor and sensor connector.
CHECK:
Measure the resistance between terminals of the throttle con-
trol motor.
OK:
Standard:
Tester ConnectionSpecified Condition
M+ (T14±2) ± M± (T14±1)0.3 to100 W (20°C (68°F))
NG Replace throttle body (See page SF±39).
OK