2001 TOYOTA SEQUOIA fuel

± DIAGNOSTICSENGINE
DI±171
365 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check air induction system (See page SF±1).
CHECK:
Check the air induction system for vacuum leaks.
NG Repair or replace air induction system.
OK
4 Perform active test (A/F control).
(a) Connect the hand±held tester to the DLC3.
(b) Start the engine and turn the tester ON.
(c) Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
(d) On the tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST /
A/F CONTROL.
(e) Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT or LEFT
button to change the fuel injection volume).
(f) Monitor the voltage outputs of A/F and HO2 sensors(AFS B1S1 (AFS B2S1) and O2S B1S2 (O2S
B2S2)) displayed on the tester.
HINT:

The A/F CONTROL operation lowers the fuel injection volume by 12.5 % or increases the injection
volume by 25 %.

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
Standard:
Tester Display
(Sensor)Injection VolumesStatusVoltages
AFS B1S1 (AFS B2S1)
(A/F)+25 %RichLess than 3.0
AFS B1S1 (AFS B2S1)
(A/F)±12.5 %LeanMore than 3.35
O2S B1S2 (O2S B2S2)
(HO2)+25 %RichMore than 0.55
O2S B1S2 (O2S B2S2)
(HO2)±12.5 %LeanLess than 0.4
Result:
Status
AFS B1S1
(AFS B2S1)Status
O2S B1S2
(O2S B2S2)A/F Condition and
A/F Sensor ConditionMisfiresSuspected Trouble AreasProceed To
Lean/RichLean/RichNormal''C
LeanLeanActual air±fuel ratio leanMay occur

PCV valve and hose

PCV hose connections

Injector blockage

Gas leakage from exhaust system

Air induction system

Fuel pressure

Mass Air Flow (MAF) meter

Engine Coolant Temperature (ECT)
sensor
A

DI±172
± DIAGNOSTICSENGINE
366 Author: Date:
2005 SEQUOIA (RM1146U)Rich
RichActual air±fuel ratio rich'

Injector leakage or blockage

Gas leakage from exhaust system

Ignition system

Fuel pressure

MAF meter

ECT sensor
A
LeanLean/RichA/F sensor malfunction'
A/F sensorB
RichLean/RichA/F sensor malfunction'
A/F sensorB
Lean: During A/F CONTROL, the A/F sensor output voltage (AFS) is consistently more than 3.35 V, and the
HO2 sensor output voltage (O2S) is consistently less than 0.4 V.
Rich: During A/F CONTROL, the AFS is consistently less than 3.0 V, and the O2S is consistently more than
0.55 V.
B Go to step 11.
C Go to step 15.
A
5 Read value of engine coolant temperature.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / COOLANT
TEMP.
CHECK:
(a) Read the COOLANT TEMP twice, when the engine is cold and also when warmed up.
Standard:
With cold engine: Same as ambient air temperature.
With warm engine: Between 75C and 95C (167F and 203F)
NG Replace engine coolant temperature sensor.
OK

± DIAGNOSTICSENGINE
DI±173
367 Author: Date:
2005 SEQUOIA (RM1146U)
6 Read value of mass air flow meter.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / MAF and
COOLANT TEMP.
(d) Allow the engine to idle until the COOLANT TEMP reaches 75C (167F) or more.
CHECK:
(a) Read the MAF with the engine in an idling condition and at an engine speed of 2,500 rpm.
Standard:
MAF while engine idling: Between 1.4 gm/s and 2.3 gm/s (shift position: N, A/C: OFF).
MAF at engine speed of 2,500 rpm: Between 5.4 gm/s and 7.9 gm/s (shift position: N, A/C: OFF).
NG Replace mass air flow meter.
OK
7 Check fuel pressure (See page SF±7).
CHECK:
Check the fuel pressure (high or low pressure).
NG Check and replace fuel pump, pressure regula-
tor, fuel pipe line and filter (See page SF±1).
OK
8 Check exhaust system for gas leakage.
OK:
No exhaust gas leakage.
NG Repair or replace exhaust gas leakage point.
OK

B17396
HT +B
AF± AF+ Sensor 1A/F Sensor Component Side:
Front View
DI±174
± DIAGNOSTICSENGINE
368 Author: Date:
2005 SEQUOIA (RM1146U)
9 Check for spark and ignition (See page IG±1).
HINT:
If the spark plugs or ignition system malfunction, engine misfire may occur. The misfire counter can be read
with the hand±held tester. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / MIS-
FIRE / CYL#1 (to CYL#8).
NG Repair or replace ignition system.
OK
10 Check injector injection (See page SF±29).
HINT:
If the injectors malfunction, engine misfires may occur. The misfire counter can be read with the hand±held
tester. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / MISFIRE / CYL#1 (to
CYL#8).
NG Replace injector.
OK
11 Check resistance of air±fuel ratio (A/F) sensor heater.
PREPARATION:
Disconnect the air±fuel ratio (A/F) sensor connector.
CHECK:
Measure resistance between the terminals of the A/F sensor
connector.
OK:
Standard:
Tester ConnectionSpecified Condition
HT (1) ± +B (2)1.8 to 3.4 W at 20C (68F)
HT (1) ± AF± (4)10 kW or higher
NG Replace air±fuel ratio (A/F) sensor.
OK

A23512
Reference (Bank 1 Sensor 1 System Drawing):
A/F Sensor A/F Relay
Heater
Sensor
A1A+ HA1A
Duty
Control ECM
From
Battery
A/F Heater
Fuse
A1A±
To EFI Relay
DI±176
± DIAGNOSTICSENGINE
370 Author: Date:
2005 SEQUOIA (RM1146U)
Standard (Check for short):
Tester ConnectionsSpecified Conditions
HT (A38±1) or HA1A (E7±2) ± Body ground
HT (A39±1) or HA2A (E7±1) ± Body ground10 kW or higher
AF+ (A38±3) or A1A+ (E7±22) ± Body ground
AF+ (A39±3) or A2A+ (E7±23) ± Body ground10 kW or higher
AF± (A38±4) or A1A± (E7±30) ± Body ground
AF± (A39±4) or A2A± (E7±31) ± Body ground10 kW or higher
NG Replace or replace harness or connector.
OK
14 Replace air fuel ratio sensor.
NEXT

A21043
Starter Relay EFI Relay
Circuit Opening
Relay
Fuel Pump RelayMREL
FPRTr2
Tr1 EFI No.1
IGNECM
FC
NE Fuel Pump
Battery
StarterFuel Pump Resistor
AM2Ignition Switch
STA
Crankshaft Position
Sensor (NE Signal)
± DIAGNOSTICSENGINE
DI±179
373 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0230 Fuel Pump Primary Circuit
CIRCUIT DESCRIPTION
In the diagram below, when the engine is cranked, current flows from terminal STAR of the ECM to the starter
relay coil and also current flows to terminal STA of the ECM (STA signal).
When the STA signal and NE signal are input to the ECM, the Tr1 is turned ON, current flows to the coil of
the circuit opening relay, the relay switches on, power is supplied to the fuel pump, and the fuel pump oper-
ates.
While the NE signal is generated (engine running), the ECM keeps the Tr1 ON (circuit opening relay ON)
and the fuel pump also keeps operating.
The fuel pump speed is controlled at two levels (high speed or low speed) by the condition of the engine
(starting, light load, heavy load). When the engine starts (STA ON), the Tr2 in the ECM is OFF, so the fuel
pump relay closes and battery positive voltage is applied directly to the fuel pump. The fuel pump operates
at high speed.
After the engine starts while idling or light loads, since the Tr2 goes ON, power is supplied to the fuel pump
via the fuel pump resistor. The fuel pump operates at low speed.
DICEW±02

DI±180
± DIAGNOSTICSENGINE
374 Author: Date:
2005 SEQUOIA (RM1146U)DTC No.
DTC Detecting ConditionTrouble Area
P0230Open or short in fuel pump relay circuit

Open or short in fuel pump relay circuit

Fuel pump relay

Circuit opening relay

Fuel pump

ECM

A23553
G±R
1 28
A 6
BECM
AM2
W±B6
32
15 3
2 121
3 2B IA1
J5
J/CL±O
I18
Ignition SW
3
7
F10
Fusible Link BlockB±R
BI530
10 26 4
12
2
114
68
1 41
5 3L±B
AM2
52HE6
2D
2F 1J1C2F
IA4
E4
E4 IG4
IA4 2H
2H 2C 1C
1JFPR
FC
MREL B±O5
J44
J45J/C E
L
BB1G±RG±REngine Room J/B
4
2F
5V V V
IL2
25
G±O G±O
B
IG2
W±B
W±BA
ED 5 4G±RIG1
B±WB±W
Instrument Panel J/B
F9
Fuel Pump
Resister
Battery2C
W±R W±R5
6
EFI No.15
C/OPN Relay Fuel Pump
Relay
EFI Relay F19
Fuel Pump
± DIAGNOSTICSENGINE
DI±181
375 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
HINT:
This diagnostic chart is based on premise that engine is started. If the engine is not started, proceed to prob-
lem symptoms table on DI±33.