2001 TOYOTA SEQUOIA oil

DIDIK±01
D13871
Combination Meter
DLC3 Stop Light SwitchECM
Park/Neutral Position SwitchSpeed Sensor (SP2) Shift Solenoid Valve S1
Shift Solenoid Valve SR
Shift Solenoid Valve SLU
Shift Solenoid Valve SL2 ATF Temperature
Sensor No. 2Integration Control and Panel
(Shift Position L Switch)
MIL
Shift Solenoid Valve SL1
Shift Solenoid
Valve SLT
ATF Temperature
Sensor No.1
Shift Solenoid Valve S2
Speed Sensor (NT)

AT Oil Temp Warning LightShift Lever
(O/D Main Switch)
4WD:
4WD Control ECU
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±519
713 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

DIDIL±01
D14205
Shift Solenoid Valve S1
MIL
(Malfunction Indicator Lamp) S1
S2
SL1
SL2
SLT
SLU
SR
WShift Solenoid Valve S2
Shift Solenoid Valve SL1
Shift Solenoid Valve SL2
Shift Solenoid Valve SLT
Shift Solenoid Valve SLU
Shift Solenoid Valve SR
OILW
AT Oil Temp Warning Light ECM Crankshaft Position Sensor
Engine CoolantTemperature Sensor
Combination Meter
Stop Lamp Switch Assy
DLC3
(Data Link Connector 3)THW VTA1, 2
VC
SPD
STPTH01
TC Throttle Position Sensor
ATF (Automatic Transmission
Fluid) Temperature Sensor No. 1Mass Air Flow Meter
Accelerator Pedal Position SensorVPA
VPA2
Shift Lever
(O/D Main Switch)
Input Speed Sensor (NT)NT
Output Speed Sensor (SP2)SP2
TH02
ATF (Automatic Transmission
Fluid) Temperature Sensor No. 2Skid Control ECUNSW
Park/Neutral Position Switch
R, D, 3, 2
VG
NE
L
ODMSIntegration Control and Panel
(Shift Position L Switch)
L4



: 4WD4WD Control ECU
CAN DI±520
± DIAGNOSTICSAUTOMATIC TRANSMISSION
714 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM
The configuration of the electronic control system in the A750E/A750F automatic transmission is as shown
in the following chart.

DIDIP±01
12345678
9 10111213141516
D13649
DLC3:
CG
TC
D13654
DI±524
± DIAGNOSTICSAUTOMATIC TRANSMISSION
718 Author: Date:
2005 SEQUOIA (RM1146U)
BASIC INSPECTION
1. CHECK FLUID LEVEL
(a) Using SST, create a short±circuit between terminals TC
and CG of the DLC3.
SST 09843±18040
(b) Start the engine and run at idle.

The A/C switch must be turned off.

On models with active height control suspension &
adaptive variable suspension, turn the height con-
trol switch off.
(c) Slowly move the shift lever through all positions from P to
L, and move it back to the P position.
(d) Switch to the fluid temperature detection mode.
Move the shift lever from the N to the D position, or from
D to N, within 1.5 seconds. (Repeat this operation for 6 se-
conds or more.)
OK: The A/T OIL TEMP warning light comes on for 2
seconds and then goes off.
(e) Return the shift lever to the P position and disconnect ter-
minals TC and CG.
(f) Idle the engine to raise oil temperature.
(g) Lift up the vehicle immediately after the meter indicator
light (ATF temperature warning light) comes on.

The A/T OIL TEMP warning light indicates the ATF
temperature according to the following table.
ATF Temp.Less than optimized
temperatureOptimized temperatureMore than optimized
temperature
A/T OIL TEMP warning lightOFFONBlinking

D13657
Add automatic transmission fluid

removing or installing the oil pan (including the oil drain)

removing the transmission valve body assy

removing the torque converter assy, etc.
Start from [*1]
In step (15)
When ATF overflowsWhen ATF does not
overflow
Go to [*2]Go to [*3]
END
disconnecting the oil cooler tube

repairing oil leaks, etc.
Start from [*4]
In step (8)
When ATF overflowsWhen ATF does not
overflow
Go to [*5]
Go to [*6]
Maximum amount of fluid
should be added when:Minimum amount of fluid
should be added when:
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±527
721 Author: Date:
2005 SEQUOIA (RM1146U)
6. ADD AUTOMATIC TRANSMISSION FLUID

D14139Overflow Plug
D14140
Refill Plug
12345678
9 10111213141516
D13649
DLC3:
CG
TC
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±529
723 Author: Date:
2005 SEQUOIA (RM1146U)
(4) Temporarily install the gasket and overflow plug.
Torque: 20 NVm (204 kgfVcm, 15 ftVlbf)
(5) Add the proper amount of ATF through the refill
hole.
NOTICE:
Refill amount differs depending on the related procedures
indicated below.
Related proceduresRefill amount
Removal and installation of oil pan1.7 liters (1.8 us qts, 1.5 lmp.qts)
Removal of transmission valve body
assy4.3 liters (4.5 us qts, 3.8 lmp.qts)
Removal of torque converter assy5.4 liters (5.7 us qts, 4.8 lmp.qts)
(6) Temporarily install the O±ring and refill plug.
Torque: 39 NVm (400 kgfVcm, 29 ftVlbf)
(7) Lower down the vehicle.
(8) Using SST, create a short±circuit between terminals
TC and CG of the DLC3.
SST 09843±18040
(9) Start the engine and run at idle.
NOTICE:

The A/C switch must be turned off.

On models with active height control suspension &
adaptive variable suspension, turn the height control
switch off.
(10) Slowly move the shift lever from the P to the 2±L
position.
Return the shift lever to the P position.

D13654
D14231
When fluid
temperature
is low: offWhen fluid
temperature
is correct: onWhen fluid
temperature
is high: blinks
D14139Overflow Plug
DI±530
± DIAGNOSTICSAUTOMATIC TRANSMISSION
724 Author: Date:
2005 SEQUOIA (RM1146U)
(11) Switch to the fluid temperature detection mode.
Move the shift lever from the N to the D position, or
from D to N, within 1.5 seconds. (Repeat this opera-
tion for 6 seconds or more.)
OK: The A/T OIL TEMP warning light comes on for 2
seconds and then goes off.
(12) Disconnect terminals TC and CG after confirming
the above condition.
(13) Idle the engine to raise the fluid temperature.
(14) Lift up the vehicle immediately after the meter indi-
cator light (ATF temperature warning light) comes
on.
NOTICE:

Add fluid only when the meter indicator light is on.

Perform this procedure while the engine is idling.
(15) Remove the overflow plug. If ATF overflows, pro-
ceed to [*2].
If ATF does not overflow, proceed to [*3].
HINT:
ºOverflowº indicates the condition under which ATF drains out
from the overflow tube.
NOTICE:
Capacity of the overflow tube is approximately 3 cc.

D14141
D14140
Refill Plug
D14138
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±531
725 Author: Date:
2005 SEQUOIA (RM1146U)
(b) When fluid overflows: [*2]
(1) Install the overflow plug with a new gasket when the
draining ATF has become a trickle.
Torque: 20 NVm (204 kgfVcm, 15 ftVlbf)
(2) Install the refill plug with a new O±ring.
Torque: 39 NVm (400 kgfVcm, 29 ftVlbf)
(3) Lower down the vehicle.
(4) Turn the ignition switch off and remove the SST.
(5) Check for fluid leaks in the transmission.
If there are leaks, it is necessary to repair or replace O±rings,
FIPGs, oil seals, plugs or other related parts.
(c) When fluid does not overflow:
[*3]
(1) Remove the refill plug.
(2) Add ATF through the refill hole until it drains out from
the overflow hole.

D14141
12345678
9 10111213141516
D13649
DLC3:
CG
TC
D13654
DI±532
± DIAGNOSTICSAUTOMATIC TRANSMISSION
726 Author: Date:
2005 SEQUOIA (RM1146U)
(3) Install the overflow plug with a new gasket when the
draining ATF has becomes a trickle.
Torque: 20 NVm (204 kgfVcm, 15 ftVlbf)
(4) Install the refill plug with a new O±ring.
Torque: 39 NVm (400 kgfVcm, 29 ftVlbf)
(5) Lower down the vehicle.
(6) Turn the ignition switch off.
(7) Check for fluid leaks in the transmission.
If there are leaks, it is necessary to repair or replace O±rings,
FIPGs, oil seals, plugs or other related parts.
(d) When adding a minimum amount of fluid: [*4]
(1) Using SST, create a short±circuit between terminals
TC and CG of the DLC3.
SST 09843±18040
(2) Start the engine and run at idle.
NOTICE:
The A/C switch must be turned off.
(3) Slowly move the shift lever from the P to the 2±L
position. Return the shift lever to the P position.
(4) Switch to the fluid temperature detection mode.
Move the shift lever from the N to the D position, or
from D to N, within 1.5 seconds. (Repeat this opera-
tion for 6 seconds or more.)
OK: The A/T OIL TEMP warning light comes on for 2
seconds and then goes off.
(5) Disconnect terminals TC and CG after confirming
the above condition.
(6) Idle the engine to raise the fluid temperature.