2001 TOYOTA SEQUOIA coolant

DIDIX±01
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±553
747 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
HINT:
If a normal code is displayed during the diagnostic trouble code check although the trouble still occurs, check
the electrical circuits for each symptom in the order given in the charts on the following pages and proceed
to the page given for troubleshooting.
The Matrix Chart is divided into 3 chapters.
1. Chapter 1: Electronic Circuit Matrix Chart
Refer to the table below when the trouble cause is considered to be electrical.
If the instruction ºProceed to next circuit inspection shown on matrix chartº is given in the flow chart
of each circuit, proceed to the circuit with the next highest number in the table to continue the check.
If the trouble still occurs even though there are no abnormalities in any of the other circuits, check and
replace the ECM.
HINT:
*1: When the circuit on which mark *1 is attached is defective, DTC could be output (see page DI±573).
SymptomSuspect AreaSee page
No up±shift
(A particular gear, from 1st to 4th gear, is not up±shifted)1. Shift solenoid valve (S1) circuit *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±641
DI±646
IN±35
No up±shift (4th " 5th)
1. O/D main switch circuit
2. Engine coolant temp. sensor circuit *1
3. Speed sensor NT circuit *1
4. Shift solenoid valve (SL1) circuit *1
5. Shift solenoid valve (SL2) circuit *1
6. Shift solenoid valve (SR) circuit *1
7. ECM
DI±688
DI±58
DI±591
DI±603
DI±631
DI±651
IN±35
No up±shift (3rd " 4th)
1. Engine coolant temp. sensor circuit *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±58
DI±646
IN±35
No up±shift (1st " 2nd)
1. Shift position L switch circuit
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±691
DI±646
IN±35
No down±shift (5th " 4th)
1. O/D main switch circuit
2. Shift solenoid valve (SL1) circuit *1
3. Shift solenoid valve (SL2) circuit *1
4. Shift solenoid valve (SR) circuit *1
5. ECM
DI±688
DI±603
DI±631
DI±651
IN±35
No down±shift (2nd " 1st)
1. Shift position L switch circuit
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±691
DI±646
IN±35
No down±shift
(A particular gear, from 1st to 4th gear, is not down±shifted)1. Shift solenoid valve (S1) circuit *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±641
DI±646
IN±35
No lock±up
1. ATF temperature sensor circuit *1
2. Stop light switch circuit *1
3. Speed sensor NT circuit *1
4. Shift solenoid valve (SLU) circuit *1
5. Engine coolant temp. sensor circuit *1
6. ECM
DI±582
DI±600
DI±591
DI±680
DI±58
IN±35
No lock±up off4. Shift solenoid valve (SLU) circuit *1
6. ECM
DI±680
IN±35

DI±554
± DIAGNOSTICSAUTOMATIC TRANSMISSION
748 Author: Date:
2005 SEQUOIA (RM1146U) Shift point too high or too low
1. Shift solenoid valve (SLT) circuit *1
2. Speed sensor NT circuit *1
3. Speed sensor SP2 circuit *1
4. Throttle position sensor circuit *1
5. ATF temperature sensor circuit *1
6. ECM
DI±662
DI±591
DI±596
DI±58
DI±582
IN±35
Up±shift to 5th from 4th while shift lever is in 4 position1. O/D main switch circuit
2. ECMDI±688
IN±35
Up±shift to 5th from 4th while engine is cold1. Engine coolant temp. sensor circuit *1
2. ECM
DI±58
IN±35
Up±shift to 4th from 3rd while shift lever is in 3 position1. Park/neutral position switch circuit *1
2. ECM
DI±576
IN±35
Up±shift to 3rd from 2nd while shift lever is in 2 position1. Park/neutral position switch circuit *1
2. ECM
DI±576
IN±35
Up±shift to 2nd from 1st while shift lever is in L position1. Shift position L switch circuit
2. ECMDI±691
IN±35
Harsh engagement (N " D)
1. Speed sensor NT circuit *1
2. Shift solenoid valve (SL1) circuit *1
3. Shift solenoid valve (SLT) circuit *1
4. ECM
DI±591
DI±603
DI±662
IN±35
Harsh engagement (Lock±up)
1. Speed sensor NT circuit *1
2. Speed sensor SP2 circuit *1
3. Shift solenoid valve (SLU) circuit *1
4. ECM
DI±591
DI±596
DI±680
IN±35
Harsh engagement (Any driving position)ECMIN±35
Poor acceleration
1. ATF temperature sensor No.2 circuit *1
2. Engine coolant temp. sensor circuit *1
3. Shift solenoid valve (SLT) circuit *1
4. ECM
DI±666
DI±58
DI±662
IN±35
No engine brakingECMIN±35
No kick±downECMIN±35
Engine stalls when starting off or stopping1. Shift solenoid valve (SLU) circuit *1
2. ECM
DI±680
IN±35
AT Oil Temp. warning light remains on1. ATF temperature sensor No.2 circuit*1DI±666
Lock±up at 3rd gear
1. AT F temperature sensor No.2 circuit 1
2. Engine coolant temp. sensor circuit *1DI±666
DI±58
Shift point too high
2. Engine coolant tem . sensor circuit
3. ECMDI 58
IN±35
Malfunction in shifting1. Park/neutral position switch circuit *1
2. ECM
DI±576
IN±35



D14152
DTC was set.
0.5 sec. 0.5 sec. 0.5 sec.
 : Freeze frame data which can be read
D14151
DLC3
1314 1516 12 11 10 9 12345678
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±563
757 Author: Date:
2005 SEQUOIA (RM1146U)
FREEZE FRAME DATA
Freeze frame data records the engine conditions (fuel system,
calculated load, engine coolant temperature, fuel trim, engine
speed, vehicle speed, etc.) when a malfunction is detected.
When troubleshooting, freeze frame data can help determine
if the vehicle was running or stopped, if the engine was warmed
up or not, if the air/fuel ratio was Lean or Rich, and other data
from the time the malfunction occurred.
The hand±held tester records freeze frame data in five different
instances: 1) 3 times before the DTC is set, 2) once when the
DTC is set, and 3) once after the DTC is set. These data can be
used to simulate the vehicle's condition around the time when
the malfunction occurred. The data may help find the cause of
the malfunction, or judge if the DTC is being caused by a tempo-
rary malfunction or not.
DLC3 (Data Link Connector 3)
The vehicle's ECM uses the ISO 15765±4 for communication
protocol. The terminal arrangement of the DLC3 complies with
SAE J1962 and matches the ISO 15765±4 format.
HINT:
Connect the cable of the hand±held tester to the DLC3, turn the
ignition switch ON and attempt to use the hand±held tester. If
the screen displays UNABLE TO CONNECT TO VEHICLE, a
problem exists in the vehicle side or the tester side.
If the communication is normal when the tool is connected to
another vehicle, inspect the DLC3 on the original vehicle.
If the communication is still impossible when the tool is con-
nected to another vehicle, the problem is probably in the tool it-
self. Consult the Service Department listed in the tool's instruc-
tion manual.
SymbolTerminal No.NameReference terminalResultCondition
SIL7Bus º+º line5 ± Signal groundPulse generationDuring transmission
CG4Chassis groundBody groundBelow 1 WAlways
SG5Signal groundBody groundBelow 1 WAlways
BAT16Battery positiveBody ground11 to 14 VAlways
CANH6HIGH±level CAN
bus lineCANL54 to 69 WIG switch OFF
CANH6HIGH±level CAN
bus lineBattery positive1 MW or higherIG switch OFF
CANH6HIGH±level CAN
bus lineCG1 kW or higherIG switch OFF
CANL14LOW±level CAN
bus lineBattery positive1 MW or higherIG switch OFF
CANL14LOW±level CAN
bus lineCG1 kW or higherIG switch OFF

DI±588
± DIAGNOSTICSAUTOMATIC TRANSMISSION
782 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0711 Transmission Fluid Temperature Sensor ºAº
Performance
CIRCUIT DESCRIPTION
See page DI±582.
DTC No.DTC Detection ConditionTrouble Area
P0711
Both (a) and (b) are detected: (2±trip detection logic)
(a) Intake air and engine coolant temps. are more than ±20°C
(±4F) at engine start
(b) After normal driving for over 22 min. and 9 km (6 mile) or
more, ATF temp. is less than 10°C (50F)

Transmission wire (ATF temperature sensor No.1)
MONITOR DESCRIPTION
This DTC indicates that there is a problem with output from the automatic transmission fluid (ATF) tempera-
ture sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF tempera-
ture to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature
and detects an open or short in the ATF temperature circuit or a fault in the ATF temperature sensor.
After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature
is below 20C (68F) after running the vehicle for a certain period, the ECM interprets this as a fault, and
turns on the MIL.
MONITOR STRATEGY
Related DTCsP0711ATF temperature sensor/Rationality check
Required sensors/ComponentsATF temperature sensor (TFT sensor)
Frequency of operationContinuous
Duration3 sec.
MIL operation2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not present.See page DI±545
TFT (transmission fluid temperature) sen-
sor circuitNot circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
IAT (Intake air temperature) sensor circuitNot circuit malfunction
Time after engine start21 min. and 40 sec.
Driving distance after engine start9 km (5.6 mile) or more±
IAT (12 sec. after engine start)±10°C (14°F) or more±
ECT (12 sec. after engine start)±10°C (14°F) or more±
DIDJ7±01

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±609
803 Author: Date:
2005 SEQUOIA (RM1146U) Shift solenoid valve SL2 circuit
Not circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
KCS sensor circuitNot circuit malfunction
ETCS (Electric throttle control system)Not system down
Transmission rangeºDº
ECT40°C (104°F) or more±
Spark advance from Max. retard timing by
KCS control0° CA or more±
EngineStarting
Transfer rangeºHIGHº*1
Transfer range ºHIGHº *1 (This condition is applied only 4WD)
*1 Following conditions met
Vehicle speed sensor circuitNot circuit malfunction
Output shaft speed sensor circuitNot circuit malfunction
Transfer output speed143 rpm or more±
NO/NOtf (Transfer input speed/Transfer
output speed)0.9 to 1.1
OFF malfunction (A)
ECM selected gear1st
Vehicle speed2 to 40 km/h (1.2 to 24.9 mph)
Throttle valve opening angle
8% or more
and 7.0% or more at 2,000 rpm
(Conditions vary with engine speed)
±
OFF malfunction (B)
Current ECM selected gear5th
Last ECM selected gear4th
Continuous time for ECM selecting 4th
gear2 sec. or more±
Actual gear when ECM selected 4th gear4th
OFF malfunction (C)
Current ECM selected gear5th
Last ECM selected gear4th
ON malfunction (A)
ECM selected gear1st
Vehicle speed2 to 40 km/h (1.2 to 24.9 mph)
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
ON malfunction (B)
ECM selected gear4th
Vehicle speed2 km/h (1.2 mph) or more±
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
ON malfunction (C)
ECM selected gear3rd
Vehicle speed2 km/h (1.2 mph) or more±

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±615
809 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Turbine speed sensor circuitNot circuit malfunction
Output speed sensor circuitNot circuit malfunction
Shift solenoid valve S1 circuitNot circuit malfunction
Shift solenoid valve S2 circuitNot circuit malfunction
Shift solenoid valve SR circuitNot circuit malfunction
Shift solenoid valve SL1 circuitNot circuit malfunction
Shift solenoid valve SL2 circuitNot circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
KCS sensor circuitNot circuit malfunction
ETCS (Electric throttle control system)Not system down
Transmission rangeºDº
ECT40°C (104°F) or more±
Spark advance from Max. retard timing by
KCS control0° CA or more±
EngineStarting
Transfer rangeºHIGHº*1
Transfer range ºHIGHº *1 (This condition is applied only 4WD)
*1 Following conditions met
Vehicle speed sensor circuitNot circuit malfunction
Output shaft speed sensor circuitNot circuit malfunction
Transfer output speed143 rpm or more±
NO/NOtf (Transfer input speed/Transfer
output speed)0.9 to 1.1
OFF malfunction (A)
ECM selected gear1st
Vehicle speed2 to 40 km/h (1.2 to 24.9 mph)
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
OFF malfunction (B)
ECM selected gear2nd
Vehicle speed2 km/h (1.2 mph) or more±
Output speed2nd " 1st down shift point or more±
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
OFF malfunction (C)
Current ECM selected gear5th
Last ECM selected gear4th
Continuous time for ECM selecting 4th
gear2 sec. or more±
Actual gear when ECM selected 4th gear4th
OFF malfunction (D)
Current ECM selected gear5th

DI±620
± DIAGNOSTICSAUTOMATIC TRANSMISSION
814 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0771 Shift Solenoid ºEº Performance
(Shift Solenoid Valve SR)
SYSTEM DESCRIPTION
The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear
position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical
problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).
DTC No.DTC Detection ConditionTrouble Area
P0771The gear required by the ECM does not match the actual gear
when driving (2±trip detection logic)

Shift solenoid valve SR remains open or closed

Shift solenoid valve SL1 remains open or closed

Valve body is blocked

Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
This DTC indicates ºstuck ON malfunctionº or ºstuck OFF malfunctionº of the shift solenoid valve SR or SL1.
The ECM commands gear shifts by turning the shift solenoid valves ºON/OFFº. When the gear position com-
manded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores
the DTC.
MONITOR STRATEGY
Related DTCsP0771Shift solenoid valve SR/Rationality check
Rid /C tMainShift solenoid valve SRRequired sensors/ComponentsSubSpeed sensor (NT), Speed sensor (NO), Crankshaft position sensor (NE)
Frequency of operationContinuous
OFF malfunction (A)0.4 sec.
DurationOFF malfunction (B) and (C)ImmediateDuration
ON malfunction0.15 sec.
MIL operation2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Turbine speed sensor circuitNot circuit malfunction
Output speed sensor circuitNot circuit malfunction
Shift solenoid valve S1 circuitNot circuit malfunction
Shift solenoid valve S2 circuitNot circuit malfunction
Shift solenoid valve SR circuitNot circuit malfunction
Shift solenoid valve SL1 circuitNot circuit malfunction
Shift solenoid valve SL2 circuitNot circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
KCS sensor circuitNot circuit malfunction
DIDJE±01

DI±626
± DIAGNOSTICSAUTOMATIC TRANSMISSION
820 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Turbine speed sensor circuitNot circuit malfunction
Output speed sensor circuitNot circuit malfunction
Shift solenoid valve S1 circuitNot circuit malfunction
Shift solenoid valve S2 circuitNot circuit malfunction
Shift solenoid valve SR circuitNot circuit malfunction
Shift solenoid valve SL1 circuitNot circuit malfunction
Shift solenoid valve SL2 circuitNot circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
KCS sensor circuitNot circuit malfunction
ETCS (Electric throttle control system)Not system down
Transmission rangeºDº
ECT40°C (104°F) or more±
Spark advance from Max. retard timing by
KCS control0° CA or more±
EngineStarting
Transfer rangeºHIGHº*1
Transfer range ºHIGHº *1 (This condition is applied only 4WD)
*1 Following conditions met
Vehicle speed sensor circuitNot circuit malfunction
Output shaft speed sensor circuitNot circuit malfunction
Transfer output speed143 rpm or more±
NO/NOtf (Transfer input speed/Transfer
output speed)0.9 to 1.1
ON malfunction (A)
ECM selected gear1st
Vehicle speed2 to 40 km/h (1.2 to 24.9 mph)
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
ON malfunction (B)
ECM selected gear3rd
Vehicle speed2 km/h (1.2 mph) or more±
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
ON malfunction (C)
ECM selected gear4th
Vehicle speed2 km/h (1.2 mph) or more±
Throttle valve opening angle7.0% or more at 2,000 rpm
(Conditions vary with engine speed)±
ON malfunction (D)
Current ECM selected gear5th
Last ECM selected gear4th