2001 TOYOTA PRIUS brake light

B04757
B04752
HV Fuse
IGCT Relay Engine Room J/B
Engine Room R/B No. 2
B04760
IN±18
± INTRODUCTIONFOR ALL OF VEHICLES
18 Author: Date:
2001 PRIUS (RM778U)

Remove the service plug with the insulated
gloves on.
If the service plug cannot be removed due to damage to the rear
portion of the vehicle, remove the HV fuse or IGCT relay
instead.
(c) Moving the damaged vehicle
HINT:
If any of the following applies, tow the vehicle away using a tow
truck lorry.

One or more of the high±voltage components and cables
is damaged.

The driving, traction, or fuel system is damaged.

The READY light is not lit when you turn ignition key to the
ON position.
NOTICE:

Before towing the vehicle away using a break down
lorry, disconnect the cable from the negative (±) ter-
minal of the auxiliary battery and remove the service
plug.
Only if none of the above applies and you see no prob-
lems that might affect the driving operation, you are
allowed to drive the vehicle away from the place of ac-
cident.

Preform the procedure below if the READY light goes
off or you detect an abnormal noise, abnormal smell,
or strong vibration while traveling:
(1) Park the vehicle in a safe place.
(2) Move the shift lever to the P position and engage
the parking brake.
(3) Disconnect the cable from the negative (±) terminal
of the auxiliary battery.
(4) Remove the service plug with insulated gloves on.

S01304
MA02H±03
MA±6
± MAINTENANCEBRAKE
59 Author: Date:
2001 PRIUS (RM778U)
BRAKE
INSPECTION
1. INSPECT BRAKE LINE PIPES AND HOSES
HINT:
Check in a well lighted area. Check the entire circumference
and length of the brake hoses using a mirror as required. Turn
the front wheels fully right or left before checking the front brake.
(a) Check all brake lines and hoses for:

Damage

Wear

Deformation

Cracks

Corrosion

Leaks

Bends

Twists
(b) Check all clamps for tightness and connections for leak-
age.
(c) Check that the hoses and lines are clear of sharp edges,
moving parts and the exhaust system.
(d) Check that the lines installed in grommets pass through
the center of the grommets.
2. INSPECT FRONT BRAKE PADS AND DISCS
(See page BR±29 )
HINT:
If a squealing or scraping noise comes from the brake during,
check the pad wear indicator to see if it is contacting the disc
rotor. If so, the disc pad should be replaced.
3. INSPECT BRAKE LININGS AND DRUMS
(See page BR±35)

A14059
B±G
EFICIR OPN
Relay
MREL Engine Room J/B
1A
B
AECM
FC
F16
Fuel
Pump
IE 5
FL Block No. 1
MAIN
F12
BatteryE8
E9 259
W±B
J17
J/C J1
J/C
IG J7
J/C IA1
IA2
W±B
AA A W±B G±R B±R
F18
FL Block No. 2EFI
Relay
1K 1F
1B10
1F
2 121
3
2
1
3
3
1
11 52 1
3
F13G±R
B±R
7 14
4
G±R
± DIAGNOSTICSENGINE
DI±161
2001 PRIUS (RM778U)
Fuel Pump Control Circuit
CIRCUIT DESCRIPTION
When starting the engine with ignition switch:
HV ECU receives ST signal and decides to start the engine, and send the signal of the engine start prior
signal to the engine ECU by the communicatio between the engine ECU and HV ECU.
Engien ECU receives that signal and turns ON the circuit opening relay slightly earlier, then turns the fuel
pump.
When starting the engine in an intermittent operation:
With the cranking by MG1, NE signal comes in immediately, so the engine ECU receives the generation of
NE signal and turns the fuel pump. (At this time, no refernce of the communication from HV ECU)
When stopping the fuel pump:
When the signal to stop the engine comes in to the engine ECU from HV ECU from HV ECU side, the fuel
pump stops.
At the time of the fuel cut opetation such as deceleration by the engine brake, the fuel pump stops.
WIRING DIAGRAM
DI7T7±01

DI82J±02
Prius Problem Check Sheet
Vehicle
Specifications
Please fill in the blanks within bold frame.Name of DealerPerson in Charge at
HeadquartersPerson in Charge
at Dealer
Model CodeOffice
Vehicle Delivery Date
Frame No.
Unit No. etc.
Option . . . :
( ) Navigation (equipped by ( ) MOP ( ) dealer) ( ) Cold climate specification
( ) others( )Problem Occurrence Date
Service Entry Date NHW11±
. .
. .Registration datemiles
. .
Contents of complaint (Status when and before/after occurring in
the order of events as correct as possible)Characteristics of Customer
Gender
Age
Occupation
Vehicle used before
Main use area
Frequency in use
Others times/day or
week or month
Status of engineOthers
Interview Results
( ) Male ( ) Female
suburbs ( ) %
Others ( ) ( ) %
city area ( ) %
mountain area ( ) %
Driving ConditionRoad Condition
Vehicle Condition
Vehicle Speed
km/h
( ) when starting
( ) when according
( ) When
normal driving
( ) when
decelerating
( ) when braking
( ) when shopping
( ) when parking
( ) when turning
( ) when
ABS actuating
( ) others
( )( ) flat road
( ) up hill ( ) down
hill incline of
° /%
distance
km
( ) dry paved road
( ) wet paved road
( ) rough paved road
( ) unpaved road
( ) snowy/frozen
road
( ) bump/curb
( ) others
( )( ) when starting
( ) right after
starting
( ) until min.
after starting
( ) until min.
after starting
of driving
( ) when shopping
system
( ) while shopping
engine
( ) when starting
engine
( ) when revolving
engineHV Battery
indication
( ) 4/4 ( ) 3/4
( ) 2/4 ( ) 1/4
( ) unidentified
Shift position
(indication)
( ) P ( ) R ( ) N
( ) D ( ) B
( ) when operating
"Weather:
A/C status
( ) no indication
( ) unidentified
( ) A/C ( ) FULL
( ) OFF
( ) unidentifiedWarning light
(MIL)
( ) ON ( ) OFF
( ) PS
( ) main battery
( ) HV!
( ) engine
( ) charge
( ) output
control
( ) brake
( ) ABS
( ) others
( )
Temperature:
°C
Brake operation
( ) brake slowly
( ) Brake suddenly
( ) use two pedals
system
Frequency in
occurrence
( ) always
( ) sometimes
( ) only once
Fuel level
( ) segmentsmphOdometer Reading
mph
°F km
± DIAGNOSTICSHYBRID VEHICLE CONTROL SYSTEM
DI±175
2001 PRIUS (RM778U)
CUSTOMER PROBLEM ANALYSIS CHECK

Verification Results of Warning Light
Engine
HV
INF. code
HV battery
Vehicle Verification Results
( ) ON ( ) OFF
( ) engine ( ) HV
( ) HV battery
( ) output control warning light
( ) brake ( ) ABS ( ) charge ( ) PS
( ) others
( )Verification Results of Diagnostic Code
Brake
PS
Vehicle Inspection Results (Verification items, reason to identify/presume the cause parts, etc.)
Replacement Parts
problem parts: No/Yes (Sending date: . . )Duplication Status
( ) always
( ) sometimes
( ) no reproduction
Confirmation Results
After Repair
( ) Normal
( ) reproduction
( ) others ( )
DI±176
± DIAGNOSTICSHYBRID VEHICLE CONTROL SYSTEM
2001 PRIUS (RM778U)

A14089
B12009
F12396
DLC3
TOYOTA Hand±held Tester
± DIAGNOSTICSHYBRID VEHICLE CONTROL SYSTEM
DI±179
2001 PRIUS (RM778U)
(b) Check the master warning light.
(1) Turn the ignition switch ON and confirm that the
master warning light comes on.
HINT:
If the master warning light does not come on, suspect a burnt
fuse, burnt bulb, or open in wiring harness.
(2) When the ºREADYº light is ON, the master warning
light should go off.
If the lamp remains on, the diagnosis system has detected a
malfunction in the system or the meassage such as ºWhen you
park your care, make sure you shift to Park P.º and ºThe batter-
ies will not charge if the shifter is Nº appears on the multi±in-
formation display.
Since DTC may be stored even though the lamp is OFF, be sure
to check DTC.
(c) Check the DTC.
(1) Prepare a TOYOTA hand±held tester.
(2) Connect the TOYOTA hand±held tester to the
DLC3.
(3) Turn the ignition switch ON and push the TOYOTA
hand±held tester main switch ON.
(4) Use the TOYOTA hand±held tester to check the
DTC, information code and freeze frame data and
note them down. (For operating instructions, see
the TOYOTA hand±held tester operator's manual).
HINT:

For one DTC, the HV diagnosis system can memorize
more than one information code and freeze frame data
corresponding to them. Therefore, when troubleshooting,
check all of the information codes, record the freeze
frame data and then start inspection according to the pro-
cedures of ºCircuit Inspectionº.

The HV ECU is communicating with each ECU of the en-
gine brake, HV battery and EMPS. So, if a warning is out-
put from the HV control system, check and record DTCs
of all ECUs. (See tables on the following pages.)
(5) See a related page to confirm details of the DTC.

F12396
TOYOTA hand±held tester
DLC3
± DIAGNOSTICSHYBRID VEHICLE CONTROL SYSTEM
DI±187
2001 PRIUS (RM778U)
(d) Clear the DTC after completion of repair.
(1) Connect the TOYOTA hand±held tester to the
DLC3.
Before clearing, check that DTCs and freeze frame
data of the HV ECU and the ECU related to the op-
eration history data are reccorded.
(2) Operate the TOYOTA hand±held tester to erase the
DTC (See the hand±held tester operator's manu-
al.).
4. FAIL±SAFE CHART
If any the following codes is recorded, the HV ECU enters the fail safe mode.
DTC codeINF. codeTrouble areaDriving condition
B2799101Immobilizeer MalfunctionImpossible to drive
C2692102Regenerative Brake Check±
C2693103Regenerative Brake Check±
104Limited driving
105Limited driving
106Limited driving
107Limited driving
108Limited driving
P1120109Accelerator Pedal Position
Sensor Circuit MalfunctionLimited drivingP1120
11 0Sensor Circuit MalfunctionLimited driving
111Limited driving
11 2Limited driving
11 3Limited driving (Creep vehicle speed)
11 4Limited driving (Creep vehicle speed)
P152011 5Stop Light Switch MalfunctionCruise control driving impossible
P156611 6Cruise Control System Mal-
functionCruise control driving impossible
P160011 7BATT MalfunctionNormal driving
11 8Impossible to drive/Normal driving when shift position is fixed
P178011 9Park/Neutral Positiont SwitchImpossible to drive/Normal driving when shift position is fixedP1780120
Park/Neutral Positiont Switch
System MalfunctionImpossible to drive
121
y
Impossible to drive/Normal driving when shift position is fixed
123Limited driving
P3000125HV B tt M lf tiLimited drivingP3000388HV Battery MalfunctionLimited driving
389Limited driving
P3001129HV Battery ECU MalfunctionLimited driving
130Limited driving
P3004131PCblMlftiImpossible to driveP3004132Power Cable MalfunctionNormal driving
133Limited driving

± DIAGNOSTICSHYBRID VEHICLE CONTROL SYSTEM
DI±195
2001 PRIUS (RM778U) MG1 CURRENT W
Electric current of MG1 W phase
MG1 INV TEMP HITemperature of inverter MG1 is high
MG1 REVMG1 revolution
MG1 TEMPMotor temperature of MG1
MG1 TEMP HIGHTemperature fo MG1 is too high
MG2 TEMP HIGHTemperature fo MG2 is too high
MG1 CURRENT VElectric cuurent of MG1 is V phase
MG1 CURRENT WElectric cuurent of MG1 is W phase
MG1 INV TEMP HITemperature of inverter MG1 is higt
MG1 REVMG1 revolution
MG1 TEMPMotor temperature of MG1
MG1 TEMP HIGHTemperature of MG1 is high
MG1 TORQMG1 torque
MG2 CURRENT VElectric cuurent of MG2 is V phase
MG2 CURRENT WElectric cuurent of MG2 is W phase
MG2 INV TEMP HITemperature of inverter MG2 is higt
MG2 REVMG2 revolution
MG2 TEMPMotor temperature of MG2
MG2 TEMP HIGHTemperature of MG2 is high
MG2 TORQMG2 torque
N RANGE OVR TIMELeaving shift gear into N position over a period of time
N RANGE CTRL1N position control due to incomplete shift gears
N RANGE CTRL2N position control due to rapid shift gear (D±R)
OCCURRENCE ORDROrder in which the trouble occurs
OCCURRNCE TRIPNumber of trips when this error occurred
OUTPUT STOPOutput stop
OUTPUT V OVEROutput voltage is too high
OVER CURRENTElectric current of the batytery is too high
OVER VOLTAGEVoltage of the battery is too high
OVR HEAT PRTECTOverheat protection
POWER RQSTPower output requested by HV ECU
PWR RESOURCE IBPower resource IB
PWR RESOURCE VMpower resource VM
RAPID SPD CHANGVehicle speed is changed too rapidly
REGEN EXEC TORQTorque volue of regenerative brake
REGEN IH FACTORInhibiting factor of regeneration
REGEN RQST TORQTorque valueof regenerative brake requested by HV ECU
REGN BRK INEFCTRegenerative brake is ineffective
RESIST OVR HEATRestriction resist is overheating
SG B IN REDUCINShifting gear into ºBº in reducing the speed
SG N IN REDUC/PShifting gear into ºNº reducing the speed
SHIFT BEF READYShifting gear before ºREADYº light turns on
SHIFT POSITIONShift position
SHIFT SENSOR1Shift sensor 1
SHIFT SENSOR2Shift sensor 2
SOCStated of charge