2001 TOYOTA AVALON tail light

AC-16
- AIR CONDITIONINGTROUBLESHOOTING (Manual A/C)
1938 Author
: Date
:
2001 AVALON (RM808U) Blinking of A/C indicator
1. Compressor
2. Drive belt
3. Compressor lock sensor
4. A/C amplifierAC-42
AC-17
AC-42
AC-77
Brightness does not change when light control switch is turned1. Headlight and taillight system
2. Heater control assemblyBE-19
AC-80

I12783
Connector ºAº
Connector ºBº
BE1DS-01
- BODY ELECTRICALCOMBINATION METER
BE-53
1657 Author
: Date
:
2001 AVALON (RM808U)
INSPECTION
1. INSPECT COMBINATION METER CIRCUIT
Disconnect connector ºAº and ºBº from the combination meter
and inspect the connectors on the wire harness side as shown
in the table.
Tester connectionConditionSpecified condition
A11 - GroundHeadlight Dimmer switch HIBattery positive voltage
A14 - GroundConstantBattery positive voltage
A15 - GroundIgnition switch ONBattery positive voltage
A16 - GroundLight control switch TAIL or HEADBattery positive voltage
A7 G dO/D main switch ONContinuityA7 - GroundO/D main switch OFFNo continuity
A19 G d
Ignition switch ON and rheostat light control vol-
ume OFF4.5 5.5 V
A19 - GroundIgnition switch ON and rheostat light control vol-
ume ONNo voltage
A20 - GroundConstantContinuity
A21 - GroundConstantContinuity
If circuit is not as specified, wiring diagram and inspect the cir-
cuits connected to other parts.

I12782
Connector ºGº
Connector ºDºConnector ºFº
Connector ºCº Connector ºEº BE-54
- BODY ELECTRICALCOMBINATION METER
1658 Author
: Date
:
2001 AVALON (RM808U)
2. INSPECT MULTI INFORMATION DISPLAY CIRCUIT
Disconnect connector ºCº, ºDº, ºEº, ºFº, ºGº from the multi in-
formation display and inspect the connectors on the wire har-
ness side as shown in the table.
Tester connectionConditionSpecified condition
C1 G dIgnition switch OFF or ACCNo voltageC1 - GroundIgnition switch ONBattery positive voltage
C3 - GroundLight control switch TAIL or HEADBattery positive voltage
C4 - C21Outside temperature a + 25 °C (77 °F)Resistance 1.6 - 1.8 kW
C5 G dEngine runningBattery positive voltageC5 - GroundEngine stoppedNo voltage
Ignition switch ON and fuel sender gauge flat UP0.3 - 0.6 V
C8 - C9Ignition switch ON and fuel sender gauge float
DOWN4.9 - 6.9 V
C9 - C19ConstantContinuity
C10 - GroundIgnition switch ON and rheostat ONNo voltage
C10 - GroundIgnition switch ON and rheostat OFF4.5 - 5.5 V
C11 - GroundConstantContinuity
C12 - GroundConstantBattery positive voltage
C13 G dIgnition switch ACC or ONBattery positive voltageC13 - GroundIgnition switch OFFNo voltage
F1 - GroundWindow washer level warning switch ONContinuity
F4 - GroundIgnition switch OFF or ACCNo voltage
F4 - GroundIgnition switch ONBattery positive voltage
G2 - GroundDoor courtesy switch ONContinuity
G3 - GroundConstantBattery positive voltage
G5 - GroundConstantBattery positive voltage

Z07425
Wire harness side:
12 123 45
67 891011
Z05732
Warning Light
Ignition
Switch
Battery
1
I14605
Warning Light
Ignition
Switch
Battery
1 2
- BODY ELECTRICALCOMBINATION METER
BE-61
1665 Author
: Date
:
2001 AVALON (RM808U)
22. INSPECT LIGHT FAILURE SENSOR CIRCUIT
Disconnect the connector from the sensor and inspect the con-
nector on the wire harness side, as shown.
Tester connectionConditionSpecified condition
1 - GroundConstantContinuity*
2 - GroundConstantContinuity*
9 - GroundConstantContinuity*
10 - GroundConstantContinuity*
11 - GroundConstantContinuity
12 - GroundConstantContinuity*
3 - GroundLight control switch OFFNo voltage
3 - GroundLight control switch TAIL or HEADBattery positive voltage
4, 8 - GroundIgnition switch LOCK or ACCNo voltage
4, 8 - GroundIgnition switch ONBattery positive voltage
7 - GroundStop light switch OFFNo voltage
7 - GroundStop light switch ONBattery positive voltage
*: There is resistance because this circuit is grounded through
the bulb.
If the circuit is as specified, replace the sensor.
If the circuit is not as specified, inspect the circuits connected
to other parts.
23. INSPECT OPEN DOOR WARNING LIGHT
Disconnect the connector from the door courtesy switch, and
ground terminal 1 on the wire harness side connector and
check that the warning light lights up.
If the warning light does not light up, inspect the bulb or wire har-
ness.
24. INSPECT DOOR COURTESY SWITCH
(See page BE-31)
25. INSPECT SEAT BELT WARNING LIGHT
(a) Disconnect the connector from the terminals buckle
switch and ground terminal on the wire harness side con-
nector as shown in the illustration.
(b) Turn the ignition switch ON and check that the warning
light lights up.
If the warning light does not light up, check the bulb circuit.

BE1DK-07
I12789
For Adjustment in
Vertical Direction
For Adjustment in
Vertical Direction
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE-23
1627 Author
: Date
:
ADJUSTMENT
1. ADJUST HEADLIGHT AIMING

I18944
0.4 °
3 m (9.84 ft) H 20.9 mm
(0.823 in.)
7
V RH Line
90 °
V LH Line4V LH LineV Line V RH Line 65
6
V LH LineV Line
V RH Line 6
5
6
H4
O: step No.
7
H4
20.9 mm
(0.823 in.)
20.9 mm
(0.823 in.) 1,342mm (52.8 in.) Low Beam:
High Beam:20.9 mm
(0.823 in.)
20.9 mm
(0.823 in.)
1,342mm (52.8 in.)
1,342mm
(52.8 in.) Hight Bearm
Low Bearm BE-24
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
1628 Author
: Date
:
2. ADJUST HEADLIGHT AIM ONLY
(a) Place the vehicle in the following conditions.

The area around the headlight is not deformed.

The vehicle is parked on a level surface.

Tire inflation pressure is the specified value.

A driver is in the driver's seat and the vehicle is in a state ready for driving (with a tank full).

The vehicle has been bounced several times.
(b) Check the headlight aiming.
(1) Prepare a thick white paper.
(2) Stand the paper perpendicular to the ground at the position 9.84 ft away from the headlights.
(3) Ensure that the center line of the vehicle and the paper face forms a 90-degree angle as shown
in the illustration.
(4) Draw a horizontal line (H line) on the paper, showing where the headlights should strike.
(5) Draw a vertical line (V line) to where the center line of the vehicle is to be.
(6) Draw 2 vertical lines (by connecting the low and high beam center marks) to where the both head-
lights should strike (V RH and V LH lines).
(7) Draw a horizontal line (by connecting the both low beam center marks) to where the headlights
should strike (H RH and H LH lines).
HINT:
The H RH and H LH line is 0.4° below the horizontal line (H line) of the light axis.
(8) Start the engine.
(9) Turn the headlights ON.
(10) Check that the headlights properly strike the position shown in the illustration.
(11) If not, adjust the lights in the vertical direction.
HINT:
As shown in the illustration, adjust each aim of the RH and LH lights.
(c) When adjusting it in the vertical direction:
Using adjusting bolt, adjust the headlight aim to within the specified range.

BE0HW-03
I12793
Combination Switch

Wiper and Washer Switch
Spiral Cable Switch Body
Combination Switch

Light Control Switch

Headlight Dimmer Switch
BE-18
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
1622 Author
: Date
:
2001 AVALON (RM808U)
COMPONENTS

I12794
13 16 15 14 9 8
17 HIAUTO
LO
OFF
FlashTAIL
3
21 54 6
7
10 12 11
BE1DJ-01
I05741
1 2
3
4
12 34
I0502712
3 5
1
2 3
5
I05741
1 2
3
4
1 23 4
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE-19
1623 Author
: Date
:
2001 AVALON (RM808U)
INSPECTION
1. INSPECT LIGHT CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF-No continuity
TAIL14 - 16Continuity
HEAD13 - 14 - 16Continuity
AUTO12 - 13 - 14 - 16Continuity
If continuity is not as specified, replace the switch.
2. INSPECT HEADLIGHT DIMMER SWITCH CONTINU-
ITY
Switch positionTester connectionSpecified condition
Flash7 - 8 - 16Continuity
Low beam16 - 17Continuity
High beam7 - 16Continuity
If continuity is not as specified, replace the switch.
3. INSPECT HEADLIGHT CONTROL RELAY CONTINU-
ITY
ConditionTester connectionSpecified condition
Constant3 - 4Continuity
Apply B+ between
terminals 3 and 4.1 - 2Continuity
If continuity is not as specified, replace the relay.
4. INSPECT TAILLIGHT CONTROL RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 - 2Continuity
Apply B+ between
terminals 1 and 2.3 - 5Continuity
If continuity is not as specified, replace the relay.
5. INSPECT D.R.L. NO.2 RELAY CIRCUIT
ConditionTester connectionSpecified condition
Constant3 - 4Continuity
Apply B+ between
terminals 3 and 4.1 - 2Continuity
If continuity is not as specified, replace the relay.