2001 TOYOTA AVALON brake sensor

SA0VA-02
F06451
N´m (kgf´cm, ft´lbf) : Specified torque

Non-reusable part
Shock Absorber211 (2,150, 156)
8.0 (82, 71 in.´lbf)
ABS Speed Sensor
Brake Caliper
49 (500, 36)

Cotter PinDisc

Cotter Pin
Steering Knuckle with Axle Hub
Lower Ball Joint
123 (1,250, 90)

Cotter Pin
127 (1,300, 94)
Lower Suspension Arm

Dust Deflector
Drive ShaftTie Rod End
Lock Cap
107 (1,090, 79)
294 (3,000, 217)
SA-36
- SUSPENSION AND AXLEFRONT LOWER BALL JOINT
1370 Author
: Date
:
2001 AVALON (RM808U)
FRONT LOWER BALL JOINT
COMPONENTS

SA0ER-03
F08681
Rear Axle CarrierNo.2 Lower
Suspension Arm
Brake Caliper
Rear Axle Hub Hub Bolt
Strut Rod ABS
Speed Sensor No.1 Lower
Suspension Arm
O-Ring
N´m (kgf´cm, ft´lbf) : Specified torque
Non-reusable part
Disc

Reused Nut : 196 (2,000, 145)
New Nut : 255 (2,600, 188)
80 (820, 59)
181 (1,850, 134)
47 (475, 34)
8.0 (82, 71 in.´lbf)
113 (1,150, 83)
SA-44
- SUSPENSION AND AXLEREAR AXLE HUB
1378 Author
: Date
:
2001 AVALON (RM808U)
REAR AXLE HUB
COMPONENTS

SA0W6-02
R10948
Z00206
W03211
A
A
B
- SUSPENSION AND AXLEREAR AXLE HUB
SA-45
1379 Author
: Date
:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the brake caliper and disc.
Torque: 47 N´m (475 kgf´cm, 34 ft´lbf)
(b) Support the brake caliper securely.
3. CHECK BEARING BACKLASH AND AXLE HUB DEVI-
ATION
(a) Using a dial indicator, check the backlash near the center
of the axle hub.
Maximum: 0.05 mm (0.0020 in.)
If the backlash exceeds the maximum, replace the axle hub.
(b) Using a dial indicator, check the deviation at the surface
of the axle hub outside the hub bolt.
Maximum: 0.07 mm (0.0028 in.)
If the deviation exceeds the maximum, replace the axle hub.
4. DISCONNECT ABS SPEED SENSOR
Remove the bolt and disconnect the ABS speed sensor.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
5. REMOVE REAR AXLE HUB
(a) Remove the 4 bolts and rear axle hub.
Torque: 80 N´m (820 kgf´cm, 59 ft´lbf)
(b) Remove the O-ring.
HINT:
At the time of installation, coat a new O-ring with MP grease.
(c) Support the backing plate securely.
6. REMOVE REAR AXLE CARRIER
(a) Loosen the 3 nuts.
Torque:
Nut A (Reused nut): 196 N´m (2,000 kgf´cm, 145 ft´lbf)
Nut A (New nut): 255 N´m (2,600 kgf´cm, 188 ft´lbf)
Nut B: 181 N´m (1,850 kgf´cm, 134 ft´lbf)

SA0VF-02
F07385
N´m (kgf´cm, ft´lbf) : Specified torque
Non-reusable part

38 (390, 28)
51 (520, 38)
51 (520, 38)
56 (570, 41)
181 (1,850, 134)
19 (195, 14)
181 (1,850, 134)
113 (1,150, 83)
5.4 (55, 48 in.´lbf)
113 (1,150, 83)
43 (440, 32)
Suspension Member Lower Stopper Suspension Member Lower Stopper
Suspension Member
Adjusting
TubeStabilizer
Bar Bracket
Suspension
Arm Washer
No. 2 Lower Suspension Arm
No. 1 Lower Suspension Arm
Parking Brake Cable
Strut Rod
Heated Oxygen
Sensor

Gasket Tailpipe
Center Exhaust Pipe

GasketSuspension Member Upper Stopper43 (440, 32)
SA-56
- SUSPENSION AND AXLEREAR LOWER SUSPENSION ARM AND STRUT ROD
1390 Author
: Date
:
2001 AVALON (RM808U)
REAR LOWER SUSPENSION ARM AND STRUT ROD
COMPONENTS