2001 TOYOTA AVALON sensor

I12769
1 2
3
5
- BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
BE-79
1683 Author
: Date
:
2001 AVALON (RM808U)
(d) Reverse the polarity and check that pulse is generated.
If operation is not as specified, replace the motor.
NOTICE:
If connecting the wire harness wrongly, the sensor might
be damaged so caution is necessary.
17. INSPECT JAM PROTECTION FUNCTION
NOTICE:
Never, ever be caught any part of your body when check-
ing.
HINT:
In case of performing resetting of the limit switch, do checking
after repeating up and down of the glass with automatic opera-
tion.
(a) Confirmation of AUTO up operation:
Confirm that the window will be fully close with AUTO up
operation.
(b) Checking of the operation of the jam protection function:
(1) Move up the window with AUTO up operation and
check that the window will go down when it touches
the handle of the hammer stetted.
(2) Confirm that the window will then stop going down
about 200 mm.
HINT:
In case of removing the glass, glass guide, regulator and etc.
be sure to perform checking of the jam protection function.
If the jam protection is not function properly, adjust power win-
dow motor reset switch and pulse switch.

BE0I6-05
I12529
Stop Light Switch
Driver Side Junction Block

STOP Fuse
Light Failure Sensor
Stop Light
HI-Mounted Stop Light
- BODY ELECTRICALSTOP LIGHT SYSTEM
BE-35
1639 Author
: Date
:
2001 AVALON (RM808U)
STOP LIGHT SYSTEM
LOCATION

- BODY ELECTRICALTROUBLESHOOTING
BE-3
1607 Author
: Date
:
2001 AVALON (RM808U)
INTERIOR LIGHT SYSTEM:
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before checking the body control system.
BACK-UP LIGHT SYSTEM:
SymptomSuspect AreaSee page
Back-Up Light does not light up.
1. GAUGE Fuse
2. Ignition Switch
3. Park/Neutral Position Switch
4. Back-up Light Relay (Column Shift)
5. Bulb
6. Wire Harness-
BE-16
DI-199
BE-34
-
-
Back-Up Light remains always ON.
1. Park/Neutral Position Switch
2. Back-up Light Relay (Column Shift)
3. Wire HarnessDI-199
BE-34
-
Only one light does not light up.1. Bulb
2. Wire Harness-
-
STOP LIGHT SYSTEM:
SymptomSuspect AreaSee page
Stop light does not light up.
1. STOP Fuse
2. GAUGE Fuse
3. Stop Light Switch
4. Light Failure Sensor
5. Wire Harness-
-
BE-36
BE-53
-
Only one light always lights up.1. Wire Harness-
Only one light does not light.1. Bulb
2. Wire Harness-
-
WIPER AND WASHER SYSTEM:
SymptomSuspect AreaSee page
Wiper and washers do not operate.
1. IG 1 Relay
2. WIPER Fuse
3. Wiper Switch
4. Wiper Motor
5. Wire Harness-
-
BE-38
BE-38
-
Wipers do not operate in LO or HI.
1. Wiper Switch
2. Wiper Motor
3. Wire HarnessBE-38
BE-38
-
Wipers do not operate in INT.
1. Wiper Fuse
2. Wiper Switch
3. Wiper Motor
4. Wire Harness-
BE-38
BE-38
-
Washer motor does not operate.
1. Washer Switch
2. Washer Motor
3. Wire HarnessBE-38
BE-38
-
Wipers do not operate when washer switch in ON.1. Washer Motor
2. Wire HarnessBE-38
-
Washer fluid does not operate.1. Washer Hose and Nozzle-

In wiper switch HI position, the wiper blade is in contact with
the body.

When the wiper switch is OFF, the wiper blade does not
retract or the retract position is wrong.1. *1Wiper Switch
2. Wire HarnessBE-38
-
*1: Inspect wiper arm and blade set position

BE-4
- BODY ELECTRICALTROUBLESHOOTING
1608 Author
: Date
:
2001 AVALON (RM808U)
COMBINATION METER (Meter, Gauges and Illumination):
SymptomSuspect AreaSee page
Tachometer, Fuel Gauge and Engine Coolant Temperature Gauge
do not operate.
1. ECU-B Fuse
2. ECU-IG No. 2 Fuse
3. Meter Circuit Plate
4. Wire Harness
5. Multi Display-
-
BE-43
-
-
Speedometer does not operate.
1. Vehicle Speed Sensor (ABS - ECU)
2. Meter Circuit Plate
3. Wire Harness
4. Multi DisplayBE-53
BE-43
-
-
Tachometer does not operate.
1. EFI - ECU
2. Meter Circuit Plate
3. Wire Harness
4. Multi Display-
BE-43
-
-
Fuel Gauge does not operate or abnormal operation.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Meter Circuit Plate
4. Wire HarnessBE-53
BE-53
BE-43
-
Engine Coolant Temperature Gauge does not operate or abnormal
operation.
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Meter Circuit Plate
4. Wire HarnessBE-53
BE-53
BE-43
-
All illumination lights do not light up.
1. Bulb
2. PANEL Fuse
3. Light Control Rheostat
4. Wire Harness-
-
BE-53
-
Brightness does not change even when rheostat turned.
1. Bulb
2. Rheostat
3. Wire Harness-
-
-
Only one illumination light does not light up.1. Bulb
2. Wire Harness-
-
COMBINATION METER (Warning Lights):
SymptomSuspect AreaSee page
Warning lights do not light up. (Except Discharge, Open Door and
SRS)
1. Bulb
2. GAUGE No. 1 Fuse
3. Meter Circuit Plate
4. Wire Harness-
-
BE-53
-
Low Oil Pressure warning light does not light up.
1. Multi Display
2. Bulb
3. Low Oil Pressure Warning Switch
4. Meter Circuit Plate
5. Wire Harness-
-
BE-53
BE-43
-
Fuel Level warning light does not light up.
1. Multi Display
2. Bulb
3. Fuel Sender Gause
4. Meter Circuit Plate
5. Wire Harness-
-
BE-53
BE-43
-
ABS warning light does not light up.
1. Bulb
2. ABS ECU
3. Wire Harness-
DI-210
-

- BODY ELECTRICALTROUBLESHOOTING
BE-5
1609 Author
: Date
:
2001 AVALON (RM808U) Seat Belt warning light does not light up.
1. Bulb
2. Body Control System
3. Meter Circuit Plate
4. Wire Harness-
DI-615
BE-53
-
Discharge warning light does not light up.
1. AM2 - Fuse
2. Bulb
3. Meter Circuit Plate
4. Wire Harness
5. Generator-
-
BE-53
-
CH-9
Light Failure warning light does not light up.
1. Bulb
2. Light Failure Sensor
3. Bulb Check Relay
4. Wire Harness
5. Taillight System-
BE-53
BE-53
-
BE-2
Brake warning light does not light up.
1. Bulb
2. Parking Brake Switch
3. Brake Fluid Level Warning Switch
4. Bulb Check Relay
5. Meter Circuit Plate
6. Wire Harness-
BE-53
BE-53
BE-53
BE-43
-
SRS Warning light does not light up.
1. AM2 - Fuse
2. Bulb
3. Airbag Sensor Assembly
4. Meter Circuit Plate
5. Wire Harness-
-
RS-62
RS-67
BE-43
Open Door warning light does not light up.
1. DOME Fuse
2. Bulb
3. Door Courtesy Switch
4. Body Control System
5. Meter Circuit Plate
6. Wire Harness-
-
BE-31
DI-615
BE-43
-
Washer Level warning light does not light up.
1. Bulb
2. Washer Fluid Level Warning Switch
3. Meter Circuit Plate
4. Wire Harness-
BE-53
BE-43
-
COMBINATION METER (Indicator Lights):
SymptomSuspect AreaSee page
O/D OFF indicator light does not light up.
1. Bulb
2. O/D OFF Switch
3. ECM
4. Meter Circuit Plate
5. Wire Harness-
DI-203
DI-1
BE-43
-
Cruise Control indicator light does not light up.
1. Bulb
2. Cruise Control ECU
3. Meter Circuit Plate
4. Wire Harness-
DI-549
BE-43
-
High beam indicator light does not light up.
1. Bulb and Taillight
2. Headlight System
3. Meter Circuit Plate
4. Wire Harness-
BE-2
BE-43
-
Turn indicator light does not light up.
1. Bulb
2. Turn Signal and Hazard Warning System
3. Meter Circuit Plate
4. Wire Harness-
BE-2
BE-43
-

BO2OU-01
N12124
N12125
BO-22
- BODYREAR DOOR
1807 Author
: Date
:
2001 AVALON (RM808U)
ADJUSTMENT
1. ADJUST DOOR IN FORWARD/REARWARD AND VER-
TICAL DIRECTIONS
(a) Remove the front door scuff plate.
(b) Remove the center pillar lower garnish.
(c) Remove the front seat belt floor anchor.
(d) Remove the front seat belt retractor.
(See page BO-128)
(e) Remove the side airbag sensor assembly.
(See page RS-78)
(f) Loosen the body side hinge nuts to adjust.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
(g) Reinstall the side airbag sensor assembly.
(See page RS-81)
Torque:
(h) Reinstall the front seat belt retractor.
(See page BO-137)
Torque:
Upper bolt: 7.5 N´m (76 kgf´cm, 66 in.´lbf)
Lower bolt: 41 N´m (420 kgf´cm, 30 ft´lbf)
(i) Reinstall the front seat belt floor anchor.
Torque: 41 N´m (420 kgf´cm, 30 ft´lbf)
(j) Reinstall the center pillar lower garnish and front door
scuff plate.
2. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL
DIRECTIONS
Loosen the door side hinge bolts to adjust.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)

BR0LU-02
F09738
Sensor Rotor
Front Speed Sensor
N´m (kgf´cm, ft´lbf): Specified torque
8.0 (82, 71 in.´lbf)
5.4 (55, 48 in.´lbf)
- BRAKEFRONT SPEED SENSOR
BR-59
1458 Author
: Date
:
2001 AVALON (RM808U)
FRONT SPEED SENSOR
COMPONENTS

BR0LW-03
- BRAKEFRONT SPEED SENSOR
BR-61
1460 Author
: Date
:
2001 AVALON (RM808U)
INSTALLATION
Installation is in the reverse order of removal (See page BR-60).
AFTER INSTALLATION, CHECK SPEED SENSOR SIGNAL (See page DI-252 or DI-212)