Page 632 of 1897
DI6N9-01
F07882
Brake Actuator
(w/ ECU, Relay)Front Speed Sensor DLC1
DLC2
Sensor RotorRear Speed Sensor
ABS Warning Light
BRAKE Warning LightSensor Rotor
Front Speed Sensor
Rear Speed Sensor
Stop Light Switch
Sensor RotorActive
Lamp Relay
DI-216- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM WITH ELECTRONIC
BRAKE FORCE DISTRIBUTION (EBD)
372 Author: Date:
2001 AVALON (RM808U)
PARTS LOCATION
Page 634 of 1897
BR3890
F02201
DLC1
Ts E
1
Tc
BR3904
0.13 sec. 0.12 sec.
ON
OFF
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM WITH ELECTRONIC
BRAKE FORCE DISTRIBUTION (EBD)DI-213
369 Author: Date:
2001 AVALON (RM808U)
(d) Clear the DTC.
(1) Using SST, connect terminals Tc and E
1 of DLC1.
SST 09843-18020
(2) Turn the ignition switch ON.
(3) Clear the DTC stored in ECU by depressing the
brake pedal 8 times or more within 5 seconds.
(4) Check that the warning light shows the normal
code.
(5) Remove the SST from the terminals of DLC1.
SST 09843-18020
HINT:
Cancellation cannot be done by removing the battery cable or
ECU-IG fuse.
2. SPEED SENSOR SIGNAL CHECK (TEST MODE)
(a) Check the sensor signal.
(1) Using SST, connect terminals Ts and E
1 of DLC1.
SST 09843-18020
(2) Start the engine.
(3) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS warning
light circuit (See page DI-243).
(4) Drive vehicle straight forward.
(5) Drive vehicle at a speed faster than 45 km/h (28
mph) for several seconds.
HINT:
If the brake is applied during the check, the check routine must
be started again.
(6) Stop the vehicle.
(7) Using SST, connect terminals Tc and E
1 of DLC1.
SST 09843-18020
(8) Read the number of blinks of the ABS warning light.
HINT:
See the list of DTC shown on the next page.
If every sensor is normal, a normal code is output (A cycle
of 0.25 sec. ON and 0.25 sec. OFF is repeated).
If 2 or more malfunction codes are identified at the same
time, the lowest numbered code will be displayed 1st.
Page 635 of 1897
BR3893
Malfunction Code (Example Code 72, 76)
7
26 7
ON
OFF
0.5 sec. 0.5 sec. 0.5 sec. 0.5 sec.1.5 sec.
2.5 sec.
4 sec.
Repeat DI-214
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM WITH ELECTRONIC
BRAKE FORCE DISTRIBUTION (EBD)
370 Author: Date:
2001 AVALON (RM808U)
(9) After completing the check, disconnect the SST
from terminals Tc and E
1 of DLC1, and turn the igni-
tion switch OFF.
SST 09843-18020
DTC of speed sensor check function:
Code No.DiagnosisTrouble Area
71Low output voltage of right front speed sensor
Right front speed sensor
Sensor installation
Right front speed sensor rotor
72Low output voltage of left front speed sensor
Left front speed sensor
Sensor installation
Left front speed sensor rotor
73Low output voltage of right rear speed sensor
Right rear speed sensor
Sensor installation
Right rear speed sensor rotor
74Low output voltage of left rear speed sensor
Left rear speed sensor
Sensor installation
Left rear speed sensor rotor
75Abnormal change in output voltage of right front speed sen-
sorRight front speed sensor rotor
76Abnormal change in output voltage of left front speed sen-
sorLeft front speed sensor rotor
77Abnormal change in output voltage of right rear speed sen-
sorRight rear speed sensor rotor
78Abnormal change in output voltage of left rear speed sensorLeft rear speed sensor rotor
Page 636 of 1897
DI6NB-01
DI-218- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM WITH ELECTRONIC
BRAKE FORCE DISTRIBUTION (EBD)
374 Author: Date:
2001 AVALON (RM808U)
PROBLEM SYMPTOMS TABLE
If a normal code is displayed during DTC check but a problem still occurs, check the circuits corresponding
to each problem symptom in the order given in the table below and proceed to the relevant troubleshooting
page.
NOTICE:
When replacing ABS ECU, sensor or etc., turn the IG switch OFF.
SymptomSuspect AreaSee page
ABS does not operate
Only when 1. - 4. are all normal and the problem is still
occurring, replace the ABS ECU.
5. Check the DTC reconfirming that the normal code is
output.
6. Power source circuit
7. Speed sensor circuit
8. Check the hydraulic circuit for leakage.
DI-212
DI-231
DI-225
DI-249
ABS does not operate intermittently
Only when 1. - 4. are all normal and the problem is still
occurring, replace the ABS ECU.
1. Check the DTC reconfirming that the normal code is
output.
2. Speed sensor circuit
3. Stop light switch circuit
4. Check the hydraulic circuit for leakage.
DI-212
DI-225
DI-234
DI-249
ABS warning light abnormal1. ABS warning light circuit
2. ABS ECUDI-243
BRAKE warning light abnormal1. BRAKE warning light circuit
2. ABS ECUDI-240
DTC check cannot be done
Only when 1. and 2. are all normal and the problem is still
occurring, replace the ABS ECU.
1. ABS warning light circuit
2. Tc terminal circuit
DI-243
DI-245
Speed sensor signal check cannot be done1. Ts terminal circuit
2. ABS ECUDI-247
Page 649 of 1897
DI6NX-03
BR3583
BR3582F00010
RotorSpeed Sensor
Magnet
To ECU
+V
-VHigh Speed
Low Speed
CoilNS
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI-267
423 Author: Date:
2001 AVALON (RM808U)
CIRCUIT INSPECTION
DTC
C0200 / 31 - C1331 / 36Speed Sensor Circuit
DTC
C1332 / 38, C1333 / 39Speed Sensor Circuit
CIRCUIT DESCRIPTION
The speed sensor detects a wheel speed and sends the ap-
propriate signals to the ECU. These signals are used to control
of the ABS and VSC system. Each of the front and rear rotors
has 48 serrations.
When the rotors rotate, a magnetic field emitted by a permanent
magnet in the speed sensor generates an AC voltage. Since
the frequency of this AC voltage changes in direct proportion to
the speed of the rotor, the frequency is used by the ECU to de-
tect the speed of each wheel.
DTC No.DTC Detecting ConditionTrouble Area
C0200 / 31
C0205 / 32
C0210 / 33
C0215 / 34
When any of the following 1. to 3. is detected :
1. Vehicle speed is more than 40 km/h (25 mph), pulses
are not input for 0.01 sec.
2. After the initial start or restart and when the vehicle
speed has reached 12 km/h (7 mph), the wheel speed of
0 km/h (0 mph) is detected.
3. After the initial start or restart and when the vehicle
speed has reached 18 km/h (11 mph), the front wheel
speed of 0 km/h (0 mph) is detected.
Right front, left front, right rear, left rear speed sensor
Each speed sensor circuit
Sensor installation
C1330 / 35
C1331 / 36
C1332 / 38
C1333 / 39
Detecting abnormality in the resistance value of each speed
sensor.Right front, left front, right rear, left rear speed sensor
Each speed sensor circuit
HINT:
DTC No. C0200 / 31 and C1330 / 35 are for the right front speed sensor.
DTC No. C0205 / 32 and C1331 / 36 are for the left front speed sensor.
DTC No. C0210 / 33 and C1332 / 38 are for the right rear speed sensor.
DTC No. C0215 / 34 and C1333 / 39 are for the left rear speed sensor.
Page 650 of 1897
F09825
(Shielded)
FR-
2
IE1A2016
BR B-W
J4
J/C (Shielded) 1
A9
Right Front
Speed Sensor
19
IE1 18
IE120
BR-W
A
AA
A
BR
(Shielded)ABS & BA & TRAC
& VSC ECU
FR+ A2017
FL-
A2010
FL+ A208 L
B-R
BR (Shielded)
B-R
BR
2 1
A8
Left Front
Speed Sensor
A
(Shielded)RR-
A2012
RR+ A2011
RL-
A2014
RL+ A2013 V
LG
(Shielded) V
LG
(Shielded)Y
GIK110
IK1 11
IK112Y
G
ID111
ID1 21
ID122 2
1 A30
Right
Rear
Speed
Sensor
2
1 A29
Left
Rear
Speed
Sensor
IGBR
BR-W DI-268
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
424 Author: Date:
2001 AVALON (RM808U)
WIRING DIAGRAM
Page 651 of 1897
R14205
1
2
R14213
1
2
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI-269
425 Author: Date:
2001 AVALON (RM808U)
INSPECTION PROCEDURE
1 Check speed sensor.
Front:
PREPARATION:
(a) Remove the front fender liner.
(b) Disconnect the speed sensor connector.
CHECK:
Measure the resistance between terminals 1 and 2 of speed
sensor connector.
OK:
Resistance: 0.6 - 2.5 kW (1.6 ± 0.2 kW at 20 °C)
CHECK:
Measure the resistance between terminals 1 and 2 of speed
sensor connector and body ground.
OK:
Resistance: 1 MW or higher
Rear:
PREPARATION:
(a) Remove the seat cushion and seatback.
(b) Disconnect the speed sensor connector.
CHECK:
Measure the resistance between terminals 1 and 2 of speed
sensor connector.
OK:
Resistance: 1.2 - 2.3 kW (1.6 ± 0.1 kW at 20 °C)
CHECK:
Measure the resistance between terminals 1 and 2 of speed
sensor connector and body ground.
OK:
Resistance: 1 MW or higher
NG Replace speed sensor.
NOTICE:
Check the speed sensor signal last (See page DI-252).
OK
Page 652 of 1897
BR3795
OK NG OK NG
OK NGOK NG
DI-270
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
426 Author: Date:
2001 AVALON (RM808U)
2 Check for open and short circuit in harness and connector between each speed
sensor and ABS & BA & TRAC & VSC ECU (See page IN-30).
NG Repair or replace harness or connector.
OK
3 Check speed sensor installation.
CHECK:
Check the speed sensor installation.
OK:
The installation bolt shall be tightened properly and
no clearance is allowed between the sensor and front
steering knuckle or rear axle carrier.
NG Replace speed sensor.
NOTICE:
Check the speed sensor signal last (See page DI-252).
OK
