2001 NISSAN X-TRAIL bulb

LT-32
PARKING, LICENSE PLATE AND TAIL LAMPS
Bulb Replacement
EKS003C1
PARKING AND TAIL LAMPS
Refer to LT-42, "REAR COMBINATION LAMP" .
LICENSE PLATE LAMP
1. Remove lens of license plate lamp.
2. Turn bulb socket, then remove it.
Removal and Installation EKS003C2
PARKING AND TAIL LAMPS
Refer toLT- 4 2 , "REAR COMBINATION LAMP"
LICENSE PLATE LAMP
Removal
1. Remove the license lamp finisher. Refer to EI-22, "LICENSE
LAMP FINISHER" in “EXTERIOR & INTERIOR (EI)” section.
2. Remove the harness from installation pawl for harness.
3. Remove license plate lamp mounting screws (2 each, RH and
LH).
4. Pull out license plate lamp from licence lamp finisher.
Installation
●Install license plate lamp in the reverse order of removal, observing the tightening torque shown below.
License plate lamp mounting screwsLicense plate lamp : 12 V 5 W
SKIA4169E
Tightening torque :1.0 - 1.8 N-m (0.10 - 0.19 kg-m,9-
16 in-lb)

LT-36
FRONT FOG LAMP
Bulb Replacement
EKS003DI
1. Remove fog lamp. Refer toLT-36, "Removal and Installation" .
2. Turn plastic cap counter clockwise then remove it.
3. Unlock retaining spring, then remove bulb.
CAUTION:
●Do not touch the glass of bulb directly by hand. Keep
grease and other oily matters away from it. Do not touch
bulb by hand while it is lit or right after being turned off.
Burning may result.
●Do not leave bulb out of headlamp reflector for a long time
because dust, moisture smoke, etc. May affect the performance of headlamp. When replacing
bulb, be sure to replace it with new one.
●When bulb is installed, be sure to lock plastic cap to ensure watertightness.
Removal and Installation EKS003DJ
REMOVAL
1. Remove fender protector. Refer toEI-13, "FENDER PROTECTOR"
2. Disconnect fog lamp connector.
3. Remove fog lamp mounting bolt.
4. Pull out fog lamp from vehicle and disconnect connector.
INSTALLATION
●Install fog lamp in the reverse order of removal, observing the tightening torque shown below.
Fog lamp mounting boltFront fog lamp :12 V 55 W (H3)
PKIA0546E
PKIA0547E
Tightening torque :3.3 -7.7 N-m (0.33 - 0.79 kg-m, 29 - 69 in-lb)

REAR FOG LAMP
LT-39
C
D
E
F
G
H
I
J
L
MA
B
LT
Bulb ReplacementEKS0015L
1. Remove rear fog lamp. Refer toLT- 3 9 , "Removal and Installa-
tion" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
Removal and InstallationEKS0015M
REMOVAL
1. Remove rear fog lamp mounting screws (2).
2. Take out rear fog lamp from bumper, then disconnect connector.
INSTALLATION
Install in the reverse order of removal, paying attention to the following. Rear fog lamp : 12V 21W
SKIA0052E
SKIA0090E
Rear fog lamp mounting screws
Tightening torque : 0.98 - 1.86 N-m (0.10 - 0.18 kg-m, 9-16 in-lb)

LT-40
CLEARANCE LAMP/TAIL LAMP
CLEARANCE LAMP/TAIL LAMP
PFP:26010
Bulb Replacement (Clearance Lamp)EKS001UR
Refer to LT- 4 , "HEADLAMP"
Bulb Replacement (Taillamp)EKS001US
Refer to LT-42, "REAR COMBINATION LAMP"
Removal and Installation of Clearance LampEKS001UT
Refer to LT- 4 , "HEADLAMP"
Removal and Installation of TaillampEKS001UU
Refer to LT-42, "REAR COMBINATION LAMP"

HIGH-MOUNTED STOP LAMP
LT-41
C
D
E
F
G
H
I
J
L
MA
B
LT
HIGH-MOUNTED STOP LAMPPFP:26590
Bulb ReplacementEKS0034W
Refer toLT-26, "STOP LAMP"
Removal and InstallationEKS0034X
Refer toLT-26, "STOP LAMP"

REAR COMBINATION LAMP
LT-43
C
D
E
F
G
H
I
J
L
MA
B
LT
Bulb ReplacementEKS00164
1. Remove rear combination lamp mounting bolts (2).
2. Pull rear combination lamp toward rear of vehicle. Disengage
locating pins (3).
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb.
Removal and InstallationEKS00165
REMOVAL
1. Remove luggage-side lower finisher. Refer to EI-26, "BODY
SIDE TRIM" in "EI EXTERIOR& INTERIOR" section.
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting bolts (2).
4. Pull rear combination lamp toward rear of vehicle. Disengage
locating pins (3).
5. From outside the vehicle, pull harness grommet rearward, and
remove harness.
INSTALLATION
Install in the reverse order of removal, paying attention to the following. Stop/taillight : 12V 21/5W
Rear turn signal lamp : 12V 21W
Backup lamp : 12V 21W
SKIA0057E
SKIA0058E
Rear combination lamp
mounting bolts
Tightening torque : 4.4 - 6.4 N-m (0.45 -
0.65 kg-m, 39-56 in-lb)

LT-64
INTERIOR ROOM LAMP
Bulb Replacement
EKS003DB
INTERIOR ROOM LAMP
1. Insert a narrow slotted screwdriver in the cutout, and remove
lens.
2. Remove the bulb.
LUGGAGE ROOM LAMP
Refer to LT-64, "Bulb Replacement" in INTERIOR ROOM LAMP
Removal and InstallationEKS003DC
INTERIOR ROOM LAMP
1. Insert a narrow slotted screwdriver in the cutout, and remove
lens.
2. Remove room lamp mounting screws (2), and remove room
lamp.
3. Disconnect the interior room lamp connector.
LUGGAGE ROOM LAMP
Refer to LT-64, "Removal and Installation" in INTERIOR ROOM LAMP Room lamp : 12V 10W
PKIA0471E
PKIA0471E

LT-66
SPOT LAMPS
Bulb Replacement
EKS003DD
SPOT LAMP (WITHOUT SUNROOF)
1. Remove the lens using a clip driver or a suitable tool.
2. Remove the shade mounting screw and remove the shade from
the spot lamp.
3. Remove the bulb.
SPOT LAMP (WITH SUNROOF)
1. Remove the lens using a clip driver or a suitable tool.
2. Remove the bulb.
Removal and InstallationEKS003DE
SPOT LAMP (WITHOUT SUNROOF)
1. Using a clips driver or a suitable tool, press and remove the
metal clip of the spot lamp.
2. Disconnect the spot lamp connector.
SPOT LAMP (WITH SUNROOF)
1. Using a clips driver or a suitable tool, press and remove the
metal clip of the spot lamp.
2. Disconnect the spot lamp connector and sunroof connector.Spot lamp (Without sunroof) : 12V 8W
SKIA0064E
Spot lamp (With sunroof) : 12V 10W
SKIA0065E
PKIA0472E
SKIA0066E