2001 Acura Integra Owner's Manual

Heatin
g an d Coolin g
Proper use of the Heating and Cooling system can make the
interior dry and comfortable, and
keep the windows clear for best
visibility.
(Canadian Type-R model only)
If your car does not have air
conditioning, it can be installed at
any time. Your dealer will install a Genuine Acura air conditioning
system that meets Acura's high
quality standards and is designed to
exactly fit your car. Please contact
your dealer for more information.
Wha t Eac h Contro l Doe s
Fa n Contro l Leve r
Sliding this lever to the right
increases the fan's speed, which increases air flow. Temperatur
e Contro l Leve r

Sliding this lever to the right
increases the temperature of the air

flow.

Ai r Conditionin g (A/C ) Butto n
This button turns the air condi- tioning ON and OFF. The indicatorin the button lights when the A/C is
on.
Recirculatio
n Butto n
This button controls the source of the air going into the system. When
the indicator in this button is lit, air
from the car's interior is sent through the system again (Recircula-
tion mode). When the indicator is off, air is brought in from outside the car (Fresh Air mode).
Comfor t an d Convenienc e Feature s MOD
E BUTTON SRECIRCULATIO
N
BUTTO N AI
R CONDITIONIN G
BUTTO N

TEMPERATUR E
CONTRO L LEVE R
FA
N CONTRO L

LEVE R

Heatin
g an d Coolin g

Mod e Button s
Use the MODE buttons to select the
vents the air flows from. Some air
will flow from the dashboard corner
vents in all modes. Air flows from the center
and corner vents in the dashboard. Air flow is divided between
the vents in the dashboard and the
floor vents. Air flows from the floor

vents.
Air flow is divided between
the floor vents and the defroster
vents at the base of the windshield. Air flows from the defroster
vents at the base of the windshield.
Comfort an d Convenienc e Feature s

Heatin
g an d Coolin g
Ven t Control s
You can adjust the direction of the air coming from the dashboard vents
by moving the tab in the center of each vent up-and-down and side-to-
side.
The vents in the corners of the
dashboard can be opened and closed
with the dials underneath them. Ho
w to Us e th e Syste m
This section covers how to set up the system controls for ventilation,
heating, cooling, dehumidifying, and defrosting.
The engine must be running for the heater and air conditioning to
generate hot and cold air. The heateruses engine coolant to warm the air.
If the engine is cold, it will be several
minutes before you feel warm air
coming from the system.
The air conditioning does not rely on engine temperature.

Comfor t an d Convenienc e Feature s

CENTE
R VEN T SID
E VEN T

Heatin
g an d Coolin g
It is best to leave the system in Fresh
Air mode under almost all conditions. Keeping the system in Recirculation
mode, particularly with the A/C off,
can cause the windows to fog up.
Switch to Recirculation mode when
you are driving through smoky or dusty conditions, then switch back to
Fresh Air mode when the condition
clears.

The outside air intakes for the heating and cooling system are at
the base of the windshield. Keepthese clear of leaves and other
debris.
Ventilation
The flow-through ventilation system draws in outside air, circulates it
through the interior, then exhausts it
through vents near the hatch. 1. Slide the temperature control lever
all the way to the left.
Make sure the A/C is off.
2. Select
and Fresh Air mode.
3. Set the fan to the desired speed.

CONTINUED

Comfor t an d Convenienc e Feature s
MOD
E BUTTON S
RECIRCULATIO
N
BUTTO N
AI
R CONDITIONIN G
BUTTO N

TEMPERATUR E
CONTRO L LEVE R
FA
N CONTRO L

LEVE R

Heatin
g an d Coolin g
To Cool with A/C
1. Turn on the A/C by pressing the button. The light in the buttonshould come on when a fan speed
is selected.
2. Make sure the temperature control lever is set to maximum

cool.
3. Select

4. If the outside air is humid, select Recirculation mode. If the outside
air is dry, select Fresh Air mode.
5. Set the fan to the desired speed.
Comfor t an d Convenienc e Feature s MOD
E BUTTON SRECIRCULATIO
N
BUTTO N
AI
R CONDITIONIN G
BUTTO N

TEMPERATUR E
CONTRO L LEVE R FA
N CONTRO L

LEVE R

Heatin
g an d Coolin g
If the interior is very warm from
being parked in the sun, you can cool it down more rapidly by setting up
the controls this way:
1. Start the engine.
2. Turn on the A/C by pressing the button. Make sure the tempera-
ture control lever is all the way to
the left.
3. Set the fan to maximum speed.
4. Open the windows partially. Select and Fresh Air mode.
When the interior has cooled down to a more comfortable temperature,close the windows and set the
controls as described for normal

cooling.
Air conditioning places an extra load
on the engine. Watch the engine
coolant temperature gauge (see page 59 ) when driving in stop-and-go
traffic or climbing a long, steep hill. If it moves near the red zone, turnoff the A/C until the gauge reads
normally.

To Heat

To warm the interior:
1. Start the engine. 2. Select and Fresh Air mode.
3. Set the fan to the desired speed.
4. Adjust the warmth of the air with
the temperature control lever.
To Heat and Dehumidify with Air
Conditioning

Air conditioning, as it cools, removes moisture from the air. When used in
combination with the heater, it
makes the interior warm and dry.
1. Switch the fan on.
2. Turn on the air conditioning.
3. Select
and Fresh Air mode.
4. Adjust the temperature control
lever so the mixture of heated andcooled air feels comfortable.
This setting is suitable for all driving conditions whenever the outside
temperature is above 32°F (0°C).

CONTINUED

Comfor t an d Convenienc e Feature s

Heatin
g an d Coolin g

To Defog and Defrost

To remove fog from the inside of the windows:
1. Switch the fan on.
2. Turn on the air conditioning. 3. Select Fresh Air mode and
4. Adjust the temperature control
lever so the air flow from thedefroster vents feels warm.
5. Turn on the rear window defogger to help clear the rear window.

Comfor t an d Convenienc e Feature s
MOD
E BUTTON S

TEMPERATUR E

CONTRO L LEVE R RECIRCULATIO
N
BUTTO N AI
R CONDITIONIN G
BUTTO N
FA N CONTRO L

LEVE R

Heatin
g an d Coolin g

To remove exterior frost or ice from the windshield and side windowsafter the car has been sitting out in
cold weather:
1. Start the engine.
2. Select the Fresh Air mode and 3. Switch the fan and temperature
controls to maximum.
To rapidly remove exterior frost or ice from the windshield (on very colddays), first select the Recirculationmode. Once the windshield is clear,select the Fresh Air mode to avoid
fogging the windows. These settings direct all the air flow
to the defroster vents at the base ofthe windshield and the side windowdefroster vents. The air flow will get
warmer and clear the windows faster as the engine warms up. You can
close the side vents with the dial
underneath each vent. This will send
more warm air to the windshielddefroster vents.
For safety, make sure you have a clear view through all the windows
before driving away.
T
o Tur n Everythin g Of f

To shut off the system temporarily, slide the fan speed and temperature
control levers all the way to the left.
You should shut the system completely off only for the first few
minutes of driving in cold weather,
until the engine coolant warms up enough to operate the heater. Keep
the fan on at all other times so stale air does not build up in the interior.
Comfor t an d Convenienc e Feature s