L PART NUMBER OF CONNECTORS
Code Part Name Part NumberCodePart Name Part Number
Note : Not all of the above part numbers of the connector are established for the supply. In case of ordering
a connector or terminal with wire, please confirm in advance if there is supply for it using ªParts Catalog
Newsº (published by Parts Engineering Administration Dept.).
A 1A/C Condenser Fan Motor90980±10928
A 2A/C Magnetic Clutch and Lock Sensor90980±10942
A 3A/C Triple Pressure SW
(A/C Dual and Single Pressure SW)90980±10943
A 4ABS Actuator90980±11413
A 5ABS Actuator90980±10891
A 6ABS Actuator and ECU90080±98070
A 7ABS and Traction Actuator90980±11698
A 8ABS and Traction Actuator90980±11413
A 9ABS Speed Sensor Front LH90980±11075A10ABS Speed Sensor Front RH90980±11 075
A11Air Fuel Ratio Sensor90980±11178
A12A/C Amplifier90980±10807
A13A/C Evaporator Temp. Sensor90980±10825
A14A/C SW90980±10631
A15ABS and Traction ECU90980±11390
A16ABS and Traction ECU90980±11391
A17ABS and Traction ECU90980±11424A18ABS ECU90980±11424
A19ABS ECU90980±11390
A20Air Vent Mode Control Servo Motor90980±11165
A22Airbag Squib
(Front Passenger Airbag Assembly)90980±11884
A23Airbag Squib (Steering Wheel Pad)90980±10850
A24Ashtray Illumination81945±33010
A25ABS Speed Sensor Rear LH90980±11060A26ABS Speed Sensor Rear RH90980±11060
A27Auto Antenna Motor and Relay90980±11697
A28Air Fuel Ratio Sensor (Bank 1 Sensor 1)90980±11178A29Air Fuel Ratio Sensor (Bank 2 Sensor 1)90980±11 178
A30A/C Ambient Temp. Sensor90980±11070
A31Airbag Sensor Front LH90980±11856A32Airbag Sensor Front RH90980±11 856
A33A/C Blower Motor Linear Controller90980±11676
A34A/C Control Assembly90980±11390
A35A/C Control Assembly90980±11391
A36A/C Room Temp. Sensor90980±10825
A37A/C Solar Sensor90980±11918
A38Air Inlet Control Servo Motor90980±11165
A39Air Mix Control Servo Motor90980±11319
A40Automatic Light Control Sensor90980±11107
B 1Back±Up Light SW90980±11250
B 2Brake Fluid Level Warning SW90980±11207
B 3Blower Motor90980±10903
B 4Blower Resistor90980±10976
B 5Blower SW90980±10877
B 6Buckle SW LH90980±10825B 7Buckle SW LH90980±10825
B 8Blower Resistor (Low Speed)90980±10976
C 1Camshaft Position Sensor90980±10947C 2Crankshaft Position Sensor90980±10947
C 3Cruise Control Actuator90980±11150
C 4Cigarette Lighter90980±10760
C 5Cigarette Lighter Illumination90980±11148
C 6Clock90980±11013
C 7Clutch Start SW90980±10825
C8Combination Meter (TMC Made)90980±11114C 8Combination Meter (TMMK Made)90980±98048
C9Combination Meter (TMC Made)90980±11113C 9Combination Meter (TMMK Made)90980±98046
C10Combination Meter (TMC Made)90980±11115C10Combination Meter (TMMK Made)90980±98047
C11Combination SW90980±11594
C12Combination SW90980±11616
C13Combination SW90980±11672
C14Cruise Control Clutch SW90980±10906
C15Cruise Control ECU90980±11391
C16Condenser90980±10860
C17Center Airbag Sensor Assembly90980±11869
C18Center Airbag Sensor Assembly90980±11872
C19Center Airbag Sensor Assembly90980±11867
D1Data Link Connector 1 (1MZ±FE)90980±11195D 1Data Link Connector 1 (5S±FE)90980±11323
D 2Daytime Running Light Resistor90980±10928
D 3Diode (A/C)90980±11071
D 4Data Link Connector 290980±11417
D 5Data Link Connector 390980±11665
D6Daytime Running Light Relay (Main)90980±11058D 6Daytime Running Light Relay (Main)90980±11 058
D7Di d (C t )D7Diode (Courtesy)D 7Diode (Courtesy)90980±10962D10Diode (Dome)90980±10962
D11Diode (Idle±Up)90980±11071
D12Door Courtesy SW Front LH
D13Door Courtesy SW Front RH90980±10871D14Door Courtesy SW Rear LH90980±10871
D15Door Courtesy SW Rear RH
D16Door Key Lock and Unlock SW Front LH90980±11490D17Door Key Lock and Unlock SW Front RH90980±11490
L
CodePart Name Part NumberCodePart Name Part Number
R12Rear Speaker LH90980±10860R13Rear Speaker RH90980±10860
R14Rear Window Defogger90980±10792R15Rear Window Defogger90980±10792
Remote Control Mirror LH
(TMC Made w/ Mirror Heater)90980±10558
R16
Remote Control Mirror LH
(TMC Made w/o Mirror Heater)90980±10395
R16Remote Control Mirror LH
(TMMK Made w/ Mirror Heater)90980±11487
Remote Control Mirror LH
(TMMK Made w/o Mirror Heater)90980±11489
Remote Control Mirror RH
(TMC Made w/ Mirror Heater)90980±10558
R17
Remote Control Mirror RH
(TMC Made w/o Mirror Heater)90980±10395
R17Remote Control Mirror RH
(TMMK Made w/ Mirror Heater)90980±11487
Remote Control Mirror RH (TMMK Made
w/o Mirror Heater)90980±11489
S 1Starter90980±09689
S 2Starter90980±11400
S 3Shift Lock ECU90980±11488
S 4Stereo Component Amplifier90980±10848
S 5Stereo Component Amplifier90980±10807
S 6Stop Light SW90980±11118
S 7Side Airbag Sensor LH90980±11857S 8Side Airbag Sensor RH90980±11 857
S 9Side Airbag Squib LH90980±11864S10Side Airbag Squib RH90980±11864
T 1Theft Deterrent Horn90980±11235
T 2Throttle Position Sensor90980±11261
T 3Theft Deterrent ECU90980±11424
T 4Theft Deterrent ECU90980±11392
T 5Traction Off SW90980±11013
T 6Turn Signal Flasher82751±50010
T 7Transponder Key Amplifier90980±10789
U 1Unlock Warning SW90980±10860
V 1Vapor Pressure Sensor90980±11860
V 2Vehicle Speed Sensor (Combination Meter)90980±11143
V 3Vehicle Speed Sensor (Electronically
Controlled Transmission)90980±11156
V4VSV (EGR)(1MZ±FE)90980±11149V 4VSV (EGR)(5S±FE)90980±11156V 5VSV (EVAP)90980±11 156
V 6VSV (Intake Air Control)90980±11149
V 7VSV (Vapor Pressure Sensor)90980±11859
V 8Vanity Light LH90980±10621V 9Vanity Light RH90980±10621
W 1Washer Level Warning SW90980±11068
W 2Washer Motor90980±10981
W 3Water Temp. Sender90980±11428
W 4Water Temp. SW No.190980±11235
W 5Water Temp. SW No.290980±11243
W 6Wireless Door Lock ECU90980±11264
BE±4
± BODY ELECTRICALBODY ELECTRICAL SYSTEM
2224 Author: Date:
Taillight does not light.
(Headlight does not light)1. Integration Relay (I/P J/B No.1)
2. Light Control Switch
3. Wire HarnessBE±14
BE±24
±
Taillight does not light.
(Headlight is normal)
1. TAIL Fuse (I/P J/B No.1)
2. Taillight Control Relay (I/P J/B No.1)
3. Integration Relay (I/P J/B No.1)
4. Light Control Switch
5. Wire Harness±
BE±24
BE±14
BE±24
±
Only one side light does not light.1. Bulb
2. Wire Harness±
±
Rear Combination light does not light.
1. Bulb
2. Light Failure Sensor
3. Wire Harness±
BE±37
±
ºAuto Turn±off Systemº does not operate.
1. GAUGE Fuse (I/P J/B No.1)
2. Integration Relay (I/P J/B No.1)
3. Door Courtesy Switch (Driver's)
4. Wire Harness±
BE±14
BE±24
±
*Terminal L of generator and parking brake switch
TURN SIGNAL AND HAZARD WARNING SYSTEM
SymptomSuspect AreaSee page
ºHazardº and ºTurnº do not light up.
1. Hazard Warning Switch
2. Turn Signal Flasher
3. Wire HarnessBE±30
BE±30
±
The flashing frequency is abnormal.
1. Bulb
2. Turn Signal Switch
3. Wire Harness±
BE±30
±
Hazard warning light does not light up.
(Turn is normal.)1. HORN Fuse (E/G Room J/B No.2)
2. Wire Harness±
±
Hazard warning light does not light up in one direction.1. Hazard Warning Switch
2. Wire HarnessBE±30
±
*1Turn signal does not light up.
1. Ignition Switch
2. TURN Fuse (I/P J/B No.1)
3. Turn Signal Switch
4. Wire HarnessBE±14
±
BE±30
±
*2Turn signal does not light up.
1. TURN Fuse (I/P J/B No.1)
2. Turn Signal Switch
3. Wire Harness±
BE±30
±
Turn signal does not light up in one direction.1. Turn Signal Switch
2. Wire HarnessBE±30
±
Only one bulb does not light up.1. Bulb
2. Wire Harness±
±
*1: Combination meter, wiper and washer do not operate.
*
2: Combination meter, wiper and washer are normal.
INTERIOR LIGHT SYSTEM
SymptomSuspect AreaSee page
ºIlluminated Entry Systemº does not operate.
1. Door Courtesy Switch
2. Integration Relay (I/P J/B No.1)
3. Wire HarnessBE±32
BE±14
±
Only one interior light does not light up.1. Bulb
2. Wire Harness±
±
Interior light does not light up (All).1. DOME Fuse (E/G Room J/B No.2)
2. Wire Harness±
±
BE±6
± BODY ELECTRICALBODY ELECTRICAL SYSTEM
2226 Author: Date:
Washer fluid does not operate.1. Washer Hose and Nozzle±
In wiper switch HI position, the wiper blade is in contact with
the body.
When the wiper switch is OFF, the wiper blade does not
retract or the retract position is wrong.1. *1Wiper Switch
2. Wire HarnessBE±40
±
COMBINATION METER
METER, GAUGES AND ILLUMINATION:
SymptomSuspect AreaSee page
Tachometer, Fuel Gauge and Engine Coolant Temperature Gauge
do not operate.1. GAUGE Fuse (I/P J/B No.1)
2. Meter Circuit Plate
3. Wire Harness±
BE±46
±
Speedometer does not operate.
1. No.1 Vehicle Speed Sensor
2. Meter Circuit Plate
3. Wire HarnessBE±47
BE±46
±
Tachometer does not operate.
1. Igniter (5S±FE)
(1MZ±FE)
2. Meter Circuit Plate
3. Wire HarnessIG±1
IG±1
BE±46
±
Fuel Gauge does not operate or abnormal operation.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Meter Circuit Plate
4. Wire HarnessBE±47
BE±47
BE±46
±
Engine Coolant Temperature Gauge does not operate or abnormal
operation
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Meter Circuit Plate
4. Wire HarnessBE±47
BE±47
BE±46
±
All illumination lights do not light up.
1. TAIL Fuse (I/P J/B No.1)
2. Light Control Rheostat
3. Wire Harness±
BE±47
±
Brightness does not change even when rheostat turned.1. Bulb
2. Wire Harness±
±
Only one illumination light does not light up.1. Bulb
2. Wire Harness±
±
COMBINATION METER
WARNING LIGHTS:
SymptomSuspect AreaSee page
Warning lights do not light up. (Except Discharge, Open Door and
SRS)1. GAUGE Fuse (I/P J/B No.1)
2. Meter Circuit Plate
3. Wire Harness±
BE±46
±
Low Oil Pressure warning light does not light up.
1. Bulb
2. Low Oil Pressure Warning Switch
3. Meter Circuit Plate
4. Wire Harness±
BE±47
BE±46
±
Fuel Level warning light does not light up.
1. Bulb
2. Fuel Level Warning Switch
3. Meter Circuit Plate
4. Wire Harness±
BE±47
BE±46
±
ABS warning light does not light up.
1. Bulb
2. ABS ECU
3. Wire Harness±
IN±31
±
± BODY ELECTRICALBODY ELECTRICAL SYSTEM
BE±7
2227 Author: Date:
Seat Belt warning light does not light up.
1. Bulb
2. Seat Belt Buckle Switch
3. Integration Relay (I/P J/B No.1)
4. Wire Harness±
BE±47
BE±47
±
Discharge warning light does not light up.
1. IGN Fuse (I/P J/B No.1)
2. Bulb
3. Wire Harness
4. Generator (5S±FE)
(1MZ±FE)±
±
±
CH±1
CH±1
Light Failure warning light does not light up.
1. Bulb
2. Light Failure Sensor
3. Bulb Check Relay
4. Wire Harness
5. Taillight system±
BE±37
BE±47
±
BE±24
Brake warning light does not light up.
1. Bulb
2. Parking Brake Switch
3. Brake Fluid Level Warning Switch
4. Bulb Check Relay
5. Meter Circuit Plate
6. Wire Harness±
BE±47
BE±47
BE±47
BE±46
±
SRS Warning light does not light up.
1. ECU±B Fuse (E/G Room J/B No.2)
2. Bulb
3. Airbag Sensor Assembly
4. Meter Circuit Plate
5. Wire Harness±
±
DI±626
BE±46
±
Open Door warning light does not light up.
1. DOME Fuse (E/G Room J/B No.2)
2. Bulb
3. Door Courtesy Switch
4. Meter Circuit Plate
5. Wire Harness±
±
BE±32
BE±46
±
Washer Level warning light does not light up.
1. Bulb
2. Washer Fluid Level Warning Switch
3. Meter Circuit Plate
4. Wire Harness±
BE±47
BE±46
±
COMBINATION METER
INDICATOR LIGHTS:
SymptomSuspect AreaSee page
O/D OFF indicator light does not light up.
1. Bulb
2. O/D OFF Switch (A140E)
(A541E)
3. Meter Circuit Plate
4. Wire Harness±
DI±431
DI±487
BE±46
±
Cruise Control indicator light does not light up.
1. Bulb
2. Cruise Control ECU
3. Meter Circuit Plate
4. Wire Harness±
IN±31
BE±46
±
High beam indicator light does not light up.
1. Bulb
2. Meter Circuit Plate
3. Wire Harness
4. Headlight System±
BE±46
±
BE±22
Turn indicator light does not light up.
1. Bulb
2. Meter Circuit Plate
3. Wire Harness
4. Turn Signal and Hazard Warning System±
BE±46
±
BE±29
± BODY ELECTRICALBODY ELECTRICAL SYSTEM
BE±9
2229 Author: Date:
ºWindow Lock Illuminationº does not light up.1. Power Window Master SwitchBE±60
Key±off power window does not operate.
1. GAUGE Fuse (I/P J/B No.1)
2. Integration Relay (I/P J/B No.1)
3. Ignition Switch
4. Door Courtesy Switch
5. Wire Harness±
BE±60
BE±14
BE±32
±
POWER DOOR LOCK CONTROL SYSTEM
SymptomSuspect AreaSee page
ºDoor lock systemº does not operate at all.
1. POWER M±Fuse (I/P J/B No.1)
2. CIG Fuse (I/P J/B No.1)
3. DOOR Fuse (I/P J/B No.1)
4. Integration Relay (I/P J/B No.1)
5. Wire Harness±
±
±
BE±70
±
Door lock system does not operate by manual switch.
1. Power Window Master Switch
2. Door Lock Manual Switch
3. Integration Relay (I/P J/B No.1)
4. Wire HarnessBE±60
BE±70
BE±70
±
Door lock system does not operate by door key.
1. Door Key Lock and Unlock Switch
2. Integration Relay (I/P J/B No.1)
3. Wire Harness
4. Door Lock Link DisconnectedBE±70
BE±70
±
±
Fault in 2±Operation unlock function of Driver's side door key lock
and unlock switch.1. Door Key Lock and Unlock Switch
2. Integration Relay (I/P J/B No.1)
3. Wire HarnessBE±70
BE±70
±
Fault in key confine prevention operate.
1. Integration Relay (I/P J/B No.1)
2. Key Unlock Warning Switch
3. Door Courtesy Switch
4. Wire HarnessBE±70
BE±14
BE±32
±
Only one door lock does not operate.1. Door Lock Motor
2. Wire HarnessBE±70
±
SLIDING ROOF SYSTEM
SymptomSuspect AreaSee page
Sliding roof system does not operate.
(Door Lock does not operate)1. POWER M±Fuse (I/P J/B No.1)
2. Power Main Relay (I/P J/B No.1)
3. Wire Harness±
BE±60
±
Sliding roof system does not operate.
(Door Lock is normal)
1. Ignition Switch
2. Sliding Roof Control Relay and Switch
3. Sliding Roof Motor and Limit Switch
4. Wire HarnessBE±14
BE±74
BE±74
±
Sliding roof system operates abnormally.
1. Sliding Roof Control Relay and Switch
2. Sliding Roof Motor and Limit Switch
3. Wire HarnessBE±74
BE±74
±
Sliding roof system stops operation half way.
(Stones of foreign material trapped in motor assembly)1. Sliding Roof Control Relay and Switch
2. Sliding Roof Motor and Limit Switch
3. Wire HarnessBE±74
BE±74
±
ºKey±off Sliding Roofº operation does not operate.
1. DOME Fuse (E/G Room J/B No.2)
2. GAUGE Fuse (I/P J/B No.1)
3. Ignition Switch
4. Integration Relay (I/P J/B No.1)
5. Wire Harness±
±
BE±14
BE±14
±
N20136
Wire harness side:
1234
N20135
Junction block side:
1 2 3 4 5 6 7 8
10 119
12
± BODY ELECTRICALIGNITION SWITCH AND KEY UNLOCK WARNING
SWITCHBE±17
2237 Author: Date:
(b) Disconnect the connector from the integration relay and
inspect the connector on the wire harness side.
Tester connectionConditionSpecified condition
1 ± GroundLight control switch OFFNo continuity
1 ± GroundLight control switch HEAD or TAILContinuity
4 ± GroundLight control switch OFF or TAILNo continuity
4 ± GroundLight control switch HEADContinuity
2 ± Ground
3 ± GroundConstantBattery positive voltage
If the circuit is as specified, try replacing the relay with a new
one.
If the circuit is not as specified, inspect the circuits connected
to other parts.
7. INSPECT INTEGRATION RELAY (TYPE B) CIRCUIT
(a) Remove the relay from the junction block No.1 and in-
spect the connector on the junction block side.
Tester connectionConditionSpecified condition
2 ± GroundAll door courtesy switches OFF (Except Driver's
Door/ Door closed)No continuity
2 ± GroundOne of the door courtesy switches ON (Except
Driver's Door/ Door opened)Continuity
4 ± GroundDoor courtesy switches except that of the driver's
door OFF (Door closed)No continuity
4 ± GroundOne of the door courtesy switches except that of
the driver's door ON (Door opened)Continuity
N20135
Junction block side:
1 2 3 4 5 6 7 8
10 119
12
± BODY ELECTRICALIGNITION SWITCH AND KEY UNLOCK WARNING
SWITCHBE±19
2239 Author: Date:
A6 ± GroundPassenger's door courtesy switch ON (Door
opened)Continuity
A7 ± GroundPassenger's door unlock detection switch OFF
(Door locked)No continuity
A7 ± GroundPassenger's door unlock detection switch ON
(Door unlocked)Continuity
A9 ± GroundRear door unlock detection switch OFF (Door
locked)No continuity
A9 ± GroundRear door unlock detection switch ON (Door
unlocked)Continuity
A11 ± A12
A12 ± A25ConstantContinuity
A16 ± GroundDoor lock manual switch OFF or UNLOCKNo continuity
A16 ± GroundDoor lock manual switch LOCKContinuity
A17 ± GroundDoor lock manual switch OFF or LOCKNo continuity
A17 ± GroundDoor lock manual switch UNLOCKContinuity
A18 ± GroundDriver's and passenger's door key lock and
unlock switch OFF or UNLOCKNo continuity
A18 ± GroundDriver's or passenger's door key lock and unlock
switch LOCKContinuity
A19 ± GroundDriver's door key lock and unlock switch OFF or
LOCKNo continuity
A19 ± GroundDriver's door key lock and unlock switch
UNLOCKContinuity
A20 ± GroundPassenger's door key lock and unlock switch
OFF or LOCKNo continuity
A20 ± GroundPassenger's door key lock and unlock switch
UNLOCKContinuity
A1 ± GroundConstantBattery positive voltage
B1 ± GroundLight control switch OFFNo voltage
B1 ± GroundLight control switch TAIL or HEADBattery positive voltage
B4 ± GroundLight control switch OFF or TAILNo voltage
B4 ± GroundLight control switch HEADBattery positive voltage
B2 ± Ground
B3 ± GroundConstantBattery positive voltage
If the circuit is as specified, try replacing the relay with a new
one.
If the circuit is not as specified, inspect the circuits connected
to other parts.
8. INSPECT INTEGRATION RELAY (TYPE C) CIRCUIT
(a) Remove the relay from the junction block No.1 and in-
spect the connector on the junction block side.