2000 SUZUKI SWIFT check engine light

An Example of Freeze Frame Data
1. Trouble Code P0102 (1st)
2. Engine Speed 782 RPM
3. Eng Cool Tmp. 80C
4. Vehicle Spd. 0 km/h
5. MAP Sensor 39 kPa
6. St. Term FT1– 0.8% Lean
7. Lg. Term FT1– 1.6% Lean
8. Fuel 1 Stat. Closed Loop
9. Fuel 2 Stat. Not used
10. Load value 25.5%
1st, 2nd or 3rd in parentheses here represents which
position in the order the malfunction is detected.
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-7
Warm-up Cycle
A warm-up cycle means sufficient vehicle operation such that the
coolant temperature has risen by at least 22C (40F) from engine
starting and reaches a minimum temperature of 70C (160F).
Driving Cycle
A “Driving Cycle” consists of engine startup and engine shutoff.
2 Driving Cycle Detection Logic
The malfunction detected in the first driving cycle is stored in ECM
(PCM) memory (in the form of pending DTC and freeze frame data)
but the malfunction indicator lamp does not light at this time. It lights
up at the second detection of same malfunction also in the next driv-
ing cycle.
Pending DTC
Pending DTC means a DTC detected and stored temporarily at 1
driving cycle of the DTC which is detected in the 2 driving cycle
detection logic.
Freeze Frame Data
ECM (PCM) stores the engine and driving conditions (in the from
of data as shown at the left) at the moment of the detection of a mal-
function in its memory. This data is called “Freeze frame data”.
Therefore, it is possible to know engine and driving conditions (e.g.,
whether the engine was warm or not, where the vehicle was running
or stopped, where air / fuel mixture was lean or rich) when a mal-
function was detected by checking the freeze frame data. Also,
ECM (PCM) has a function to store each freeze frame data for three
different malfunctions in the order as the malfunction is detected.
Utilizing this function, it is possible to know the order of malfunctions
that have been detected. Its use is helpful when rechecking or diag-
nosing a trouble.
Priority of freeze frame data:
ECM (PCM) has 4 frames where the freeze frame data can be
stored. The first frame stores the freeze frame data of the malfunc-
tion which was detected first. However, the freeze frame data
stored in this frame is updated according to the priority described
below. (If malfunction as described in the upper square “1” below
is detected while the freeze frame data in the lower square “2” has
been stored, the freeze frame data “2” will be updated by the freeze
frame data “1”.)
PRIORITY
FREEZE FRAME DATA IN FRAME 1
1
Freeze frame data at initial detection of malfunction
among misfire detected (P0300-P0304), fuel
system too lean (P0171) and fuel system too rich
(P0172)
2Freeze frame data when a malfunction other than
those in “1” above is detected

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-13
MALFUNCTION INDICATOR LAMP (MIL)
CHECK
1) Turn ON ignition switch (but the engine at stop) and check that
MIL lights.
If MIL does not light up (or MIL dims), go to “Diagnostic Flow
Table A-1” for troubleshooting.
2) Start engine and check that MIL turns OFF.
If MIL remains ON and no DTC is stored in ECM (PCM), go to
“Diagnostic Flow Table A-2” for troubleshooting.
DIAGNOSTIC TROUBLE CODE (DTC) CHECK
1) Prepare SUZUKI scan tool (Tech-1).
2) With ignition switch OFF, connect it to data link connector (DLC)
(1) located on underside of instrument panel at driver’s seat side.
Special Tool:
(A): SUZUKI scan tool
(B): Mass storage cartridge
(C): 16 / 14 pin DLC cable
3) Turn ignition switch ON and confirm that MIL lights.
4) Read DTC, pending DTC and freeze frame data according to
instructions displayed on scan tool and print it or write it down.
Refer to scan tool operator’s manual for further details.
If communication between scan tool and ECM (PCM) is not pos-
sible, check if scan tool is communicable by connecting it to
ECM (PCM) in another vehicle. If communication is possible in
this case, scan tool is in good condition. Then check data link
connector and serial data line (circuit) in the vehicle with which
communication was not possible.
5) After completing the check, turn ignition switch off and discon-
nect scan tool from data link connector.

6-1-20 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
ENGINE BASIC INSPECTION
This check is very important for troubleshooting when ECM (PCM) has detected no DTC and no abnormality has
been found in visual inspection.
Follow the flow table carefully.
STEP
ACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check battery voltage.
Is it 11 V or more?Go to Step 3.Charge or replace
battery.
3Is engine cranked?Go to Step 4.Go to “DIAGNOSIS”
in Section 6G.
4Does engine start?Go to Step 5.Go to Step 7.
5Check idle speed as follows:
1) Warm up engine to normal operating temp.
2) Shift transmission to neutral position for M / T
(“P” position for A / T).
3) All of electrical loads are switched off.
4) Check engine idle speed with scan tool.
See Fig. 1.
Is it 700 – 800 r / min?Go to Step 6.“ENGINE DIAGNO-
SIS TABLE” in this
section.
6Check ignition timing as follows:
1) Using SUZUKI scan tool, select “MISC” mode on
SUZUKI scan tool and fix ignition timing to initial
one. See Fig. 2.
2) Remove air cleaner bolt and shift air cleaner
position to observe ignition timing.
3) Using timing light (1), check initial ignition timing.
See Fig. 3.
Is it 5 ± 3 BTDC at specified idle speed?“ENGINE DIAGNO-
SIS TABLE” in this
section.Check ignition control
related parts referring
to Section 6F1.
7Check fuel supply as follows:
1) Check to make sure that enough fuel is filled in fuel
tank.
2) Turn ON ignition switch for 2 seconds and then
OFF. See Fig. 4.
Is fuel return pressure (returning sounds) felt from fuel
feed hose (1) when ignition switch is turned ON?Go to Step 9.Go to Step 8.
8Check fuel pump for operating.
1) Was fuel pump operating sound heard from fuel
filler for about 2 seconds after ignition switch ON
and stop?Go to “DIAG. FLOW
TABLE B-3”.Go to “DIAG. FLOW
TABLE B-2”.
9Check ignition spark as follows:
1) Disconnect injector couplers.
2) Remove spark plugs and connect them to high
tension cords.
3) Ground spark plugs.
4) Crank engine and check if each spark plug sparks.
Is it in good condition?Go to Step 10.Go to “DIAGNOSIS”
in Section 6F1.
10Check fuel injector for operation as follows:
1) Install spark plugs and connect injector
connectors.
2) Using sound scope (1), check operating sound of
each injector (2) when cranking engine. See Fig. 5.
Was injector operating sound heard from all
injectors?“ENGINE DIAGNO-
SIS TABLE” in this
section.Go to “DIAG. FLOW
TABLE B-1”.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-29
SCAN TOOL DATA
As the data values given below are standard values estimated on the basis of values obtained from the normally
operating vehicles by using a scan tool, use them as reference values. Even when the vehicle is in good condition,
there may be cases where the checked value does not fall within each specified data range. Therefore, judgment
as abnormal should not be made by checking with these data alone.
Also, conditions in the below table that can be checked by the scan tool are those detected by ECM (PCM) and
output from ECM (PCM) as commands and there may be cases where the engine or actuator is not operating (in
the condition) as indicated by the scan tool. Be sure to use the timing light to check the ignition timing.
NOTE:

With the generic scan tool, only star () marked data in the table below can be read.

When checking the data with the engine running at idle or racing, be sure to shift M / T gear to the neutral
gear position and A / T gear to the “Park” position and pull the parking brake fully. Also, if nothing or “no
load” is indicated, turn OFF A / C, all electric loads, P / S and all the other necessary switches.
SCAN TOOL DATAVEHICLE CONDITIONNORMAL CONDITION /
REFERENCE VALUES
FUEL SYSTEM B1 (FUEL
SYSTEM STATUS)At specified idle speed after warming upCLOSED
(closed loop)

CALC LOAD
(CALCULATED LOADAt specified idle speed with no load after
warming up3 – 9%(
VALUE)At 2500 r / min with no load after warming up12 – 17%

COOLANT TEMP.
(ENGINE COOLANT
TEMP.)
At specified idle speed after warming up85 – 100C,
185 – 212F
SHORT FT BI (SHORT
TERM FUEL TRIM)At specified idle speed after warming up–20 – +20%
LONG FT BI (LONG
TERM FUEL TRIM)At specified idle speed after warming up–15 – +15%

MAP (INTAKE
MANIFOLD ABSOLUTE
PRESSURE)At specified idle speed with no load after
warming up24 – 37 kPa,
180 – 280 mmHg
ENGINE SPEEDAt idling with no load after warming up
Desired
idle speed
± 50 r / min
VEHICLE SPEEDAt stop0 km / h, 0 MPH

IGNITION ADVANCE
(IGNITION TIMING
ADVANCE FOR NO.1
CYLINDER)
At specified idle speed with no load after
warming up9 – 15 BTDC
INTAKE AIR TEMP.At specified idle speed after warming upAmbient +35C (95F)
temp.–5C (23F)
MAF (MASS AIR FLOW
RATE)
At specified idle speed with no load after
warming up0 – 4 gm / sec
RATE)At 2500 r / min with no load after warming up4 – 9 gm / sec

THROTTLE POS
(ABSOLUTE
Ignition switch
ON / engineThrottle valve fully closed7 – 18%
(ABSOLUTE
THROTTLE POSITION)
ON / engine
stoppedThrottle valve fully open70 – 100%
O2S B1 S1 (HEATED
OXYGEN SENSOR-1)At specified idle speed after warming up0.05 – 0.95 V
O2S B1 S2 (HEATED
OXYGEN SENSOR-2)When engine is running at 2000 r / min. for
3 min or longer after warming up.0 – 0.95 V
O2S FT B1 S1At specified idle speed after warning up–20 – +20%
DIS. WITH MIL ON————

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-31
SCAN TOOL DATA DEFINITIONS
FUEL SYSTEM (FUEL SYSTEM STATUS)
Air / fuel ratio feedback loop status displayed as either
open or closed loop. Open indicates that ECM (PCM)
ignores feedback from the exhaust oxygen sensor.
Closed indicates final injection duration is corrected
for oxygen sensor feedback.
CALC LOAD (CALCULATED LOAD VALUE, %)
Engine load displayed as a percentage of maximum
possible load. Value is calculated mathematically us-
ing the formula: actual (current) intake air volume

maximum possible intake air volume x 100%.
COOLANT TEMP.
(ENGINE COOLANT TEMPERATURE, C, F)
It is detected by engine coolant temp. sensor
SHORT FT B1 (SHORT TERM FUEL TRIM, %)
Short term fuel trim value represents short term
corrections to the air / fuel mixture computation. A val-
ue of 0 indicates no correction, a value greater than
0 means an enrichment correction, and a value less
than 0 implies an enleanment correction.
LONG FT B1 (LONG TERM FUEL TRIM, %)
Long term fuel trim Value represents long term correc-
tions to the air / fuel mixture computation. A value of 0
indicates no correction, a value greater than 0 means
an enrichment correction, and a value less than 0 im-
plies an enleanment correction.
MAP (INTAKE MANIFOLD ABSOLUTE
PRESSURE, kPa, inHg)
It is detected by manifold absolute pressure sensor and
used (among other things) to compute engine load.
ENGINE SPEED (rpm)
It is computed by reference pulses from crankshaft
position sensor.
VEHICLE SPEED (km / h, MPH)
It is computed based on pulse signals from vehicle
speed sensor.
IGNITION ADVANCE
(IGNITION TIMING ADVANCE FOR NO.1
CYLINDER, )
Ignition timing of NO.1 cylinder is commanded by
ECM (PCM). The actual ignition timing should be
checked by using the timing light.
INTAKE AIR TEMP. (C, F)
It is detected by intake air temp. sensor and used to
determine the amount of air passing into the intake
manifold as air density varies with temperature.
MAF (MASS AIR FLOW RATE, gm / s, lb / min)
It represents total mass of air entering intake manifold
which is computed based on signals from MAP sen-
sor, IAT sensor, TP sensor, etc.
THROTTLE POS
(ABSOLUTE THROTTLE POSITION, %)
When throttle position sensor is fully closed position,
throttle opening is indicated as 0% and 100% full open
position.
OXYGEN SENSOR B1 S1
(HEATED OXYGEN SENSOR-1, V)
It indicates output voltage of HO2S-1 installed on ex-
haust manifold (pre-catalyst).
OXYGEN SENSOR B1 S2
(HEATED OXYGEN SENSOR-2, V)
It indicates output voltage of HO2S-2 installed on ex-
haust pipe (post-catalyst). It is used to detect catalyst
deterioration.
DESIRED IDLE (DESIRED IDLE SPEED, rpm)
The Desired Idle Speed is an ECM (PCM) internal pa-
rameter which indicates the ECM (PCM) requested
idle. If the engine is not running, this number is not valid.
TP SENSOR VOLT (THROTTLE POSITION
SENSOR OUTPUT VOLTAGE, V)
The Throttle Position Sensor reading provides throttle
valve opening information in the form of voltage.
INJ PULSE WIDTH
(FUEL INJECTION PULSE WIDTH, msec.)
This parameter indicates time of the injector drive
(valve opening) pulse which is output from ECM
(PCM) (but injector drive time of NO.1 cylinder for
multiport fuel injection).
IAC FLOW DUTY (IDLE AIR (SPEED) CONTROL
DUTY, %)
This parameter indicates current flow time rate within
a certain set cycle of IAC valve (valve opening rate)
which controls the amount of bypass air (idle speed).
TOTAL FUEL TRIM (%)
The value of Total Fuel Trim is obtained by putting val-
ues of short Term Fuel Trim and Long Term Fuel Trim
together. This value indicates how much correction is
necessary to keep the air / fuel mixture stoichiomet-
rical.
BATTERY VOLTAGE (V)
This parameter indicates battery positive voltage in-
putted from main relay to ECM (PCM).

Main
fuseIgnition
switch
Main
relay Malfunction indicator lamp in combination meter
Relay
box Fuse box
C01-1
C01-2
C01-3
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-39
TABLE A-1 MALFUNCTION INDICATOR LAMP CIRCUIT CHECK – LAMP DOES
NOT COME “ON” AT IGNITION SWITCH ON (BUT ENGINE AT STOP)
CIRCUIT DESCRIPTION
When the ignition switch is turned ON, ECM (PCM) causes the main relay to turn ON (close the contact point).
Then, ECM (PCM) being supplied with the main power, turns ON the malfunction indicator lamp (MIL). When the
engine starts to run and no malfunction is detected in the system, MIL goes OFF but if a malfunction was or is de-
tected, MIL remains ON even when the engine is running.
INSPECTION
STEPACTIONYESNO
1MIL Power Supply Check
1) Turn ignition switch ON.
Do other indicator / warning lights in
combination meter comes ON?Go to Step 2.“IG” fuse blown, main
fuse blown, ignition switch
malfunction, “B/W” circuit
between “IG” fuse and
combination meter or poor
coupler connection at
combination meter.
2ECM (PCM) Power and Ground Circuit
Check Does engine start?Go to Step 3.Go to TABLE A-3 ECM (PCM)
POWER AND GROUND
CIRCUIT CHECK.
If engine is not cranked, go to
DIAGNOSIS in SECTION 6G.
3MIL Circuit Check
1) Turn ignition switch OFF and disconnect
connectors from ECM (PCM).
2) Check for proper connection to ECM
(PCM) at terminal C03-1.
3) If OK, then using service wire, ground
terminal C03-1 in connector
disconnected.
Does MIL turn on at ignition switch ON?Substitute a
known-good ECM
(PCM) and recheck.Bulb burned out or “V” wire
circuit open.

Main
fuseIgnition
switch
Main
relay Malfunction indicator lamp in combination meter
Relay
box
Fuse box
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-41
TABLE A-3 ECM (PCM) POWER AND GROUND CIRCUIT CHECK – MIL
DOESN’T LIGHT AT IGNITION SWITCH ON AND ENGINE DOESN’T
START THOUGH IT IS CRANKED UP
CIRCUIT DESCRIPTION
When the ignition switch tuned ON, the main relay turns ON (the contact point closes) and the main power is sup-
plied to ECM (PCM).
INSPECTION
STEPACTIONYESNO
1Main Relay Operating Sound Check
Is operating sound of main relay heard at ignition switch ON?Go to Step 5.Go to Step 2.
2Main Relay Check
1) Turn OFF ignition switch and remove main relay (1).
2) Check for proper connection to main relay (1) at terminal
3 and 4.
3) Check resistance between each two terminals. See Fig. 1
and 2.
Between terminals 1 and 2: Infinity
Between terminals 3 and 4: 100 – 150 Ω
4) Check that there is continuity between terminals 1 and 2
when battery is connected to terminals 3 and 4. See Fig. 3.
Is main relay in good condition?Go to Step 3.Replace main
relay.
3Fuse Check
Is main “FI” fuse in good condition?Go to Step 4.Check for short in
circuits connected
to this fuse.
4ECM (PCM) Power Circuit Check
1) Turn OFF ignition switch, disconnect connectors from ECM
(PCM) and install main relay.
2) Check for proper connection to ECM (PCM) at terminals
C03-6, C02-10, C02-5 and C02-6.
3) If OK, then measure voltage between terminal C03-6 and
ground, C02-10 and ground with ignition switch ON.
Is each voltage 10 – 14 V?Go to Step 5.“B/W”, “W/R” or
“Gr” circuit open.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-105
Heater blower
switchRear defogger
switch Tail light relay
(Lighting switch)
Diodes in junction/
fuse block
Fig. 1 for Step 1 Fig. 2 for Step 1
TABLE B-6 ELECTRIC LOAD SIGNAL CIRCUIT CHECK
INSPECTION
STEPACTIONYESNO
1Check Electric Load Signal Circuit.
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition
switch OFF.
2) Start engine and select “DATA LIST” mode on
scan tool.
3) Check electric load signal under following each
condition. See Fig. 1.
Ignition switch ON, Small light,
heater blower fan and rear
defogger all turned OFF : OFF
0 V (C01-17)
Ignition switch ON, Small light,
heater blower fan or rear
defogger turned ON : ON
10 – 14 V (C01-17)
Is check result satisfactory?
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminals C01-17 of ECM (PCM)
connector connected, under above each condition.
See Fig. 2.
Is each voltage as specified?Electric load signal
circuit is in good
condition.“Br / Y” circuit open
or short, Electric
load diodes
malfunction or
Each electric load
circuit malfunction.