2000 MITSUBISHI MONTERO ECU

SWS -Troubleshooting54B-18
Inspection Procedure B-2
Buzzer: Center display operation annunciation function
does not work normally.Probable cause
If the center display is operating normally, the cause is probably a malfunction in
the harness between the center display and the ETACS-ECU or in the
ETACS-ECU itself.DMalfunction of center display
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
Ye s
NG
Check the center display input circuit. (Refer to P.54B-53, Inspection
Procedure P-19.)
OK
Replace the ETACS-ECU.
MUT-
IIinput signal check
DCenter display
Is the center display operating normally?NoCarry out troubleshooting for the center display. (Refer to
GROUP 54A – Center Display.)
Inspection Procedure C-1
Central door locking system: Central door locking system
does not work normally.Probable cause
The power supply circuit, the circuit shared by door lock actuators, or the
ETACS-ECU may be defective.DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
NG
NG
Repair
NG
Check the harness wire between ETACS-ECU and fusible link
(1).
OK
NG
Repair
NG
NG
Repair
OK
Replace the ETACS-ECU.
Check the harness wire between ETACS-ECU and door lock actua-
tor.
OK
Check trouble symptoms.
Check the following connectors:
D-224, D-209, D-218 , D-219 vehicles>
Measure at ETACS-ECU connector D-223.
DDisconnect connector and measure at J/B side.
DVoltage between terminal 12 and body earth.
OK:System voltage
OK
Check trouble symptoms.
Check the following connectors:
D-224, D-211, D-27


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-19
Inspection Procedure C-2
Central door locking system: Some doors do not lock or
unlock.Probable cause
The door lock actuator, or the harness wire between ETACS-ECU and the door
lock actuator may be defective.DMalfunction of driver’s, front passenger’s, rear or
back door lock actuator
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
NGReplace the defective door lock actuator.
OK
NG
Repair
OK
Check trouble symptoms.
OK
Replace the ETACS-ECU.
Check the harness wire between ETACS-ECU and defective door
lock actuator.Repair NG NG
Check the following connectors :
Front L.H. door: D-224, D-209, D-25, H-03
Front R.H. door: D-224, D-209, D-15, H-18
Rear L.H. door: D-224, D-218, D-26, F-18, H-12
Rear R.H. door:D-224, D-218, D-124, F-04, H-21
Back door: D-224, D-218, D-124, G-06, I-06
Check the following connectors :
Front L.H. door: D-224, D-209, D-31, D-15, H-03
Front R.H. door: D-224, D-209, D-31, D-25, H-18
Rear L.H. door: D-224, D-209, D-31, D-26, F-18, H-12
Rear R.H. door: D-223, D-219, F-04, H-21
Back door: D-224, D-219, G-06, I-06
Check the defective door lock actuator. (Refer to GROUP 42 –
Door or GROUP 42 - Back Door.)
Inspection Procedure C-3
Central door locking system:Some functions of central
locking system do not work.Probable cause
The ETACS-ECU operates the central door locking system, based on input
signals from the following switches:
DFront passenger’s or back door lock key cylinder switch
DDriver’s door lock actuator switch
If the system does not work normally, a defect on the relevant circuit or the
ETACS-ECU may be suspected.DMalfunction of front passenger’s or back door lock
key cylinder switch
DMalfunction of driver’s door lock actuator switch
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
NGCheck the defective input circuit. (Refer to P.54B-15, Defects Found
by Input Signal Check.)
OK
Replace the ETACS-ECU.
MUT-
IIinput signal check
DFront passenger’s or back door lock key cylinder switch
DDriver’s door lock actuator switch


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-20
Inspection Procedure C-4
Central door locking system: Forgotten key prevention
function does not work.Probable cause
The ETACS-ECU operates the forgotten key prevention function, based on the
input signals from the following switches:
DKey reminder switch
DDriver’s door switch
DDriver’s door lock actuator switch
If the function does not work normally, a defect on the relevant circuit or the
ETACS-ECU may be suspected.DMalfunction of key reminder switch
DMalfunction of driver’s door switch
DMalfunction of driver’s door lock actuator
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
NGCheck the defective input circuit. (Refer to P.54B-15, Defects Found
by Input Signal Check.)
OK
Replace the ETACS-ECU.
MUT-
IIinput signal check
DKey reminder switch
DDriver’s door switch
DDriver’s door lock actuator switch
Inspection Procedure D-1
Power window: Power window do not work at all.Probable cause
The power window relay or the ETACS-ECU may be defective.DMalfunction of power window relay
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
OK
NG
NG
Repair
NG
Check the harness wire between power window relay and fusible
link (4).OK
NG
Repair
OK
Replace the ETACS-ECU.
NG
Check the harness wire between power window relay and power
window mainswitch, power window relay and ETACS-ECU.NG
Repair
OK
Check trouble symptoms.
Check the following connectors:
D-221, D-208, D-25, H-05, D-224
Check the power window relay. (Refer to GROUP 42 – Door.)NG
Replace
OK
Check trouble symptoms.
Measure at power window relay connector D-221.
DDisconnect connector and measure at J/B side.
DVoltage between terminal 5 and body earth.
OK:System voltage
DVoltage between terminal 3 and body earth.
OK:System voltageCheck the following connectors:
D-221 D-223, D-27


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-23
Inspection Procedure D-4
Power window: Power window main switch can not
operate front passenger’s or rear window.Probable cause
The cause is probably a malfunction of the power windowmainswitch or front
passenger’s or rear power window motor, or an abnormality in the power supply
circuit.DMalfunction of power windowmainswitch
DMalfunction of front passenger’s or rear power
window motor
DMalfunction of harness wire or connector
NG
Replace the power windowmainswitch.
OK
Replace the power window motor.Check trouble symptoms.
NG
Check the harness wire between power windowmainswitch and
power window motor.NG
Repair
OK
Check trouble symptoms.
Ye s
NG
Check the power windowmainswitch input circuit. (P.54B-51, In-
spection Procedure P-16.)
OK
Check the following connectors:
Front L.H. door: H-05, D-25, D-31, D-15, H-04
Front R.H. door: H-05, D-25, D-31, D-15, H-16
Rear L.H. door: H-05, D-25, D-31, D-26, F-18, H-10
Rear R.H. door: H-05, D-25, D-31, D-124 F-04, H-23NG
Repair
MUT-
IIinput signal check
DPower windowmainswitch
Can the passenger’s side power window be operated by the
power window sub switch?NoCheck the power window sub switch circuit. (Refer to P.54B-22,
Inspection Procedure D-3.)
Inspection Procedure D-5
Power window: Power window timer function does not
work normally.Probable cause
The ETACS-ECU operates the power window timer function, based on the input
signals from the following switches:
DIgnition switch (IG1)
DDriver’s door switch
If the function does not work normally, a defect on the relevant circuit, power
window mainswitch or the ETACS-ECU may be suspected.DMalfunction of driver’s door switch
DMalfunction of power windowmainswitch
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
OK
NoNGCheck the defective input circuit. (Refer to P.54B-15, Defects Found
by input Signal Check.)
NG
Replace the power windowmainswitch.
Check trouble symptoms.Replace the ETACS-ECU.
MUT-
IIinput signal check
DIgnition switch (IG1)
DDriver’s door switch
DPower windowmainswitch
Is a diagnosis code output when the ignition switch is at the
OFF (LOCK) position?Ye sCarry out troubleshooting while referring to the Diagnosis Code
Chart on P.54B-9.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -TroubleshootingSWS -Troubleshooting54B-24
Inspection Procedure D-6
Power window: When the glass is raised, it then lowers
automatically.Probable cause
If the sliding resistance is too large when the glass isbeing raised, it is judged
that something is jammed in the window, and the window is lowered by
approximately 150 mm.DIncorrect window glass adjustment
DGlass slider is incorrectly installed or warped
DMalfunction of power window motor
OK
Replace the power window motor.NG
Replace the window regulator assembly.
Check trouble symptoms.
Check the power window operating currant. (Refer to GROUP
42 – Door.)NGAdjust the window glass. (Refer to GROUP 42 – Door.)
Inspection Procedure D-7
Power window: The glass is jammed in the window.Probable cause
The cause may be a malfunction of the revolution detection sensor in the power
window motor.DMalfunction of power window motor
Replace the power window motor.
Inspection Procedure D-8
Power window: When the glass is fully raised, it then
lowers automatically.Probable cause
The cause may be a malfunction of the revolution detection sensor in the power
window motor.DMalfunction of power window motor
NG
Replace the power window motor.
Check trouble symptoms.
After disconnecting the battery terminals, set the limit switch.
(Refer to GROUP 42 - Door.)
Inspection Procedure E-1
Keyless entry system: Keyless entry system does not
operate.Probable cause
The ETACS-ECU operates the keyless entry system, based on the input signals
from the following switches:
DKey reminder switch
DDoor switches
DDriver’s door lock actuator switch
DTransmitter
If the function does not work normally, a defect on the relevant circuit or the
ETACS-ECU may be suspected.DMalfunction of key reminder switch
DMalfunction of door switches
DMalfunction of driver’s door lock actuator switch
DMalfunction of transmitter
DMalfunction of ETACS-ECU


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-25
OK
Replace the ETACS-ECU.
NoCheck the central door locking system. (Refer to P54B-13, Trouble
Symptom Chart.)
Ye s
MUT-
IIinput signal check
DKey reminder switch
DDoor switches
DDriver’s door lock actuator switch
DTransmitterNGCheck the defective input circuit. (Refer to P.54B-15, Defects Found
by input Signal Check.)
Is the central door locking system operated normally?
Inspection Procedure E-2
Keyless entry system: The room lamp and hazard warning
lamps do not operate through the answerback function.Probable cause
The hazard warninglampanswerback function can be selected by the driver’s
desire (can be deactivated). However, the roomlampanswerback function can
not be deactivated. if all of these device do not operate through the answerback
function, the ETACS-ECU may be defective.DMalfunction of turn-signal lamp
DMalfunction of room lamp
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
Ye s
Replace the ETACS-ECU.
NG
Are the room lamp andhazard warning lamps operated normally?NoCheck the defective device. (Refer to P.54B-13, Trouble Symptom
Chart.)
Check trouble symptoms.
Activate the answerback functions. (Refer to GROUP 42 – Keyless
Entry System or P.54B-60.)
Inspection Procedure E-3
Keyless entry system: The encrypted code cannot be
registered.Probable cause
The ETACS-ECU actives the encrypted code registermode according to the
following switch signals.
DKey reminder switch
DHazard warninglampswitch
If the encrypted code registermode is notset, the relevant input signal circuit or
the ETACS-ECU may be defective.
If a transmitter can not be registered although the encrypted code registermode
is set, the transmitter or the ETACS-ECU may be defective.DMalfunction of key reminder switch
DMalfunction of hazard warninglampswitch
DMalfunction of transmitter
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
OK
Replace the ETACS-ECU.
Ye s
No
NG
Check the defective input circuit. (Refer to P.54B-15, Defects Found
by input Signal Check.)NG
Repair OKReplace the transmitter.
MUT-
IIinput signal check
DKey reminder switch
DHazard warninglampswitch
Is encrypted code registermodeset?Check the transmitter battery. (Refer to GROUP 42 - Keyless
Entry System.)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-27
Inspection Procedure F-2
Sunroof: Sunroof timer function does not work normally.Probable cause
The sunroof motor assembly operates the sunroof timer function, based on the
input signals from the following switches:
DIgnition switch (IG1)
DDriver’s door switch
If the function does not work normally, a defect on the relevant circuit, sunroof
motor assembly or the ETACS-ECU may be suspected.DMalfunction of driver’s door switch
DMalfunction of sunroof motor assembly
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
OK
NoNGCheck the defective input circuit. (Refer to P.54B-15, Defects Found
by input Signal Check.)
NG
Replace the ETACS-ECU.
Check trouble symptoms.Replace the sunroof motor assembly.
MUT-
IIinput signal check
DIgnition switch (IG1)
DDriver’s door switch
DSunroof switch
Is a diagnosis code output when the ignition switch is at the
OFF (LOCK) position?Ye sCarry out troubleshooting while referring to the Diagnosis Code
Chart on P.54B-9.
Inspection Procedure F-3
Sunroof: Safety mechanism does not work normally.Probable cause
The sunroof motor assembly monitorsload condition according to thecurrent,
which runs in the motor. If a predetermined current is exceeded, the sunroof
motor reverses due to safety mechanism. If the sunroof motor does not reverse
when an excessiveload is applied, the sunroof motorassembly may be
defective.DMalfunction of sunroof motor assembly
Replace the sunroof motor assembly.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-28
Inspection Procedure G-1
Windshield wiper and washer: Windshield wiper does not
operate.Probable cause
If the windshield wiper does not work at all, the windshield wiper motor, column
switch or the front-ECU may be defective.DMalfunction of windshield wiper motor
DMalfunction of column switch
DMalfunction of front-ECU
DMalfunction of harness wire or connector
OK
NG
Replace
NG
Repair
NG
Repair
NG
Check the harness wire between windshield wiper motor and body
earth.
NG
Repair
NG
Check the harness wire between front-ECU and ignition switch
(ACC).
OK
Check trouble symptoms.
OK
Check trouble symptoms.
OK
Replace the front-ECU.
NG
NG
Repair
Check the harness wire between front-ECU and windshield wiper
motor.
OK
Check trouble symptoms.
OK
Check the following connectors:
B-12, A-05, A-08X
OK
Measure at front-ECU connector A-08X.
DDisconnect connector and measure at relay box side.
DTurn the ignition switch to ACC position.
DVoltage between terminal 24 and body earth.
OK:System voltageNGCheck the following connectors:
A-08X, D-27, D-223, D-208
OK
Measure at windshield wiper motor connector B-12.
DDisconnect connector and measure at harness side.
DContinuity between terminal 5 and body earth.
OK:ContinuityNGCheck the following connector:
B-12
Check the windshield wiper motor. (Refer to GROUP 51 – Wind-
shield Wiper and Washer.)
MUT-
IIinput signal check
DWindshield mist wiper switch
DWindshield intermittent wiper switch
DWindshield low-speed wiper switch
DWindshield high-speed wiper switchNGCheck the defective input circuit. (Refer to P.54B-15, Defects Found
by Input Signal Check.)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk