2000 MITSUBISHI MONTERO fuel pump

GDI -Troubleshooting 13A-183
OK
Check the following items in that order.
DCheck the sparkplug
DCheck the EGR control system
DCheck the compression pressure
DCheck the fuel filter or fuelline for clogging
OK
Check ignition coil spark for each cylinder.
1. Remove the ignition coil.
2. Install a new sparkplug to the removed ignitioncoil.
3. Disconnect the injector intermediate connector.
Caution
Never touch the connector terminal as approx. 100 V is
applied to the injector, or you are seriously injured.
4. Earth the sparkplug electrodesecurely.
5. Check that the sparkplug igniteswhen theengine is
cranked.NGReplace the ignition coil.
OK
Measure fuel high-pressure between the fuel pump (high
pressure) and injector. (Refer to P.13A-222.)NGRepair
From the previouspage
Check the trouble symptoms.Replace the injector. NG
OK
MUT-
IIActuator Test
08 Purge control solenoid valve
(Refer to P.13A-203.)NGCheck the purge control solenoid valve system
(Refer to P.13A-197, Inspection procedure 36.)
Inspection procedure 14
The feeling of impact or vibration when accelerating
Probable cause
In cases such as the above, the cause is probably that there is an ignition leak
accompanying the increase in the sparkplug demand voltage during
acceleration.DMalfunction of the ignition system
Replace the ignition coil.
NG
OK
Check the trouble symptoms.
OK
Check the sparkplugNGReplace
NO
MUT-
IIData list
79 Throttle position sensor (1st channel) (Refer to P.13A-198.)NGCheck the throttle valve position feedback system
(Refer to P.13A-162, code No.92.)
MUT-
IISelf-Diag Code
Is a diagnosis code displayed?YESRefer to P.13A-130, INSPECTION CHART FOR DIAGNOSIS
CODES.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-185
Inspection procedure 18
Too high CO and HC concentration when idling
Probable cause
Abnormal air-fuel ratio is suspected.DMalfunction of the air/fuel ratio control system
DDeteriorated catalyst
OK
To the nextpage
NG
Replace the ignition coil.
OK
Check ignition coil spark for each cylinder.
1. Remove the ignition coil.
2. Install a new sparkplug to the removed ignitioncoil.
3. Disconnect the injector intermediate connector.
Caution
Never touch the connector terminal as approx. 100 V is applied to the injector, or you are seriously injured.
4. Earth the sparkplug electrodesecurely.
5. Check that the sparkplug igniteswhen theengine iscranked.NG
NG
Measure fuel high -pressure between the fuelpump (high
pressure) and injector. (Refer to P.13A-223.)
Check the trouble symptoms.
OK
MUT-
IIData list
11 Oxygen sensor (Refer to P.13A-198.)
OK:
Repeat 0 - 400 mV and 600 - 1,000 mV alternately
during idling(wait for at least 2 minutes after the
enginestarted to run at idle).OKReplace the oxygen sensor.
OK
MUT-
IIData list
11 Oxygen sensor (Refer to P.13A-198.)
OK:
600 - 1,000 mV when theengine is suddenlyracedNGCheck the oxygen sensor system. (Refer to P.13A-131, code
No.11.)
OK
MUT-
IIActuator Test
08 Purge control solenoid valve
(Refer to P.13A-203.)NGCheck the purge control solenoid valve system
(Refer to P.13A-197, Inspection procedure 36.)
OK
MUT-
IIData list
68 EGR valve (Refer to P.13A-198.)NGCheck the EGR valve system (Refer to P.13A-196, Inspection
procedure 35.)
OK
MUT-
IIData list
25 Barometric pressure sensor (Refer to P.13A-198.)NGCheck the barometric pressure sensor system (Refer to
P.13A-145, code No.25.)
OK
MUT-
IIData list
13 Intake air temperature sensor (Refer to P.13A-198.)NGCheck the intake air temperature sensor system (Refer to
P.13A-135, code No.13.)
OK
MUT-
IIData list
21 Engine coolant temperature sensor (Refer to P.13A-198.)NGCheck theengine coolant temperaturesensor system (Refer
to P.13A-138, code No.21.)
NO
Check the ignition timing. (Refer to GROUP 11A - Engine
Adjustment.)NGCheck that the crankanglesensor andtiming beltcover are
properly installed.
MUT-
IISelf-Diag Code
Are diagnosis codes displayed?YESRefer to P.13A-130, INSPECTION CHART FOR DIAGNOSIS
CODES.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-193
Inspection procedure 29
Fuel pump (low pressure) system
Probable cause
The engine-A/T-ECU turns on the fuelpumprelay while theengine iscranking
or running, and supplies power source to the fuelpump(low pressure).DMalfunction of the fuel pumprelay
DMalfunction of the fuel pump(low pressure)
DImproper connector contact,opencircuit or
short-circuited harness wire
DMalfunction of the engine-A/T-ECU
Check the ignition switch (Refer to
GROUP54 - Ignition Switch.)
NG
Repair
OK
OK
NG
OK
Check the trouble symptoms.NGReplace the fuel pump(low
pressure).
NG
Replace the engine-A/T-ECU.OKRepair
OK
Normal
NG
Repair
NG
Check the harness wire between the
fuel pumprelay and the fuelpump
(low pressure). NG
(1) NG
NG
NG
Check the harness wire between the
fuel pump(low pressure) and earth,
and repair if necessary.
(2) NG
NG
NG
NG
Repair
OK
OK
Check the following connector:
G-12NG
Repair
Check the trouble symptoms.
Check the following connector
:
F-11
OK
Check the trouble symptoms.
Check the following connectors:
B-27X, D-124, E-17, F-11Measure at fuel pump(low pressure)
connector G-12.
DDisconnect the connector, and
measure at the harness side.
(1) The voltage between terminal 5
and earth
(Ignition switch: ON)
OK:
System voltage
(2) The continuity between terminal 4
and earth
OK:
Continuity
Check the trouble symptoms.
OK
Measure at the engine-A/T-ECU
connector D-119.
DDisconnect the connector, and
measure at the harness side.
DShort circuit between terminal 21
and earth
(Ignition switch: ON)
OK:
The fuel pump operates.
(Its operation sound can be
heard.)OKCheck the following connector
:
D-119
OK
Measure at the engine-A/T-ECU
connector D-119.
DDisconnect the connector, and
measure at the harness side.
DThe voltage between terminal 21
and earth
(Ignition switch: ON)
OK:
System voltageNGCheck the harness wire between the
fuel pumprelay and the
engine-A/T-ECU, and repair if
necessary.
Check the harness wire between the
fuel pumprelay and the ignition
switch.
OK
Check the trouble symptoms.
Check the following connectors:
D-208, D-213, E-10Measure at the fuel pumprelay
connector B-27X.
DDisconnect the connector, and
measure at the harness side.
DThe voltage between terminal 3,
4 and earth
(Ignition switch: ON)
OK:
System voltage
OK
Check the fuelpumprelay (Refer to
P.13A-227.)NG
Replace
MUT-
IIActuator Test
07 Fuel pump
(Refer to P.13A-203.)
Repair


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-203
ACTUATOR TEST REFERENCE TABLE
Item
No.Inspection
itemDrive ContentsInspection contentsNormal condi-
tionInspec-
tion pro-
cedure
No.Reference
page
01InjectorCut fuel to the
No.1 injector.Engine:
Idling after warming-upIdling condition
becomes differ-Code
No. 4113A-147
02Cut fuel to the
No.2 injector.
(Cut the fuel supply to each
injector in turn and check
cylinders which does notent (becomes
unstable, or the
engine stalls).
03Cut fuel to the
No.3 injector.affect idling.)
04Cut fuel to the
No.4 injector.
05Cut fuel to the
No.5 injector.
06Cut fuel to the
No.6 injector.
07Fuel pump
(low-pres-
sure)Operates the
fuel pump (low-
pressure) to cir-
culate fuel.Ignition
switch:
ONPinch the return
hose with fin-
gers to feel the
pulse of the fuel
being circulated.Pulse is felt.Proce-
dure
No.2913A-193
Operating
sound can be
heard around
the fuel tank.Sound of opera-
tion can be
heard
08Purge con-
trol solenoid
valveSolenoid valve
turns from OFF
to ON.Ignition switch: ONSound of opera-
tion can be
heard when so-
lenoid valve is
driven.Proce-
dure
No.3613A-197
17Basic ignition
timingSolenoid valve
turns from OFF
to ON.DEngine: Idling
DSet a timing light.
5_BTDC--
21Condenser
fanDrive the fan
motorDIgnition switch: ON
DA/C switch: ON
Fan motor runsProce-
dure
No.2113A-187
34Electronic-
controlled
throttle valve
systemStop the throttle
control servoIgnition switch: ONThe throttle
valve opens
slightlyCode
No. 9113A-161


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting 13A-205
Terminal
No.Normal condition Check condition (Engine condition) Check item
18Condenser fan relayCondenser fan not operatingSystem voltage
Condenser fan operating0 - 3 V or more
19Air flow sensor resetEngine: Idling0-1V
signal
Engine speed: 3,000 r/min6-9V
20A/C relayDEngine: Idling
DA/C switch: OFF to ON (Compressor operating)System voltage or
changes momentarily 6
V or more to 0 - 3 V
21Fuel pump relayIgnition switch: ONSystem voltage
Engine: Idling0-3V
22Engine warning lampIgnition switch: OFF to ONSystem voltage
23GDI ECO indication
lampIgnition switch: OFF to ON0 - 3 V (system voltage
after five seconds)
Rev the engine suddenly.System voltage
34Purge control solenoidDEngine coolantEngine: stoppedSystem voltage
valvetemperature: 80 -
95_C
DIgnition switch:
ON
Engine: After starting, in-
crease the engine speed
up to 3,500 r/minThe voltage drops
41Power supplyIgnition switch: ONSystem voltage
47
43Engine ignition signalEngine speed: 3,000 r/min0.3 - 3.0 V
44Engine coolant tem-
perature sensorIgnition switch: ONWhen engine coolant tem-
perature is 0_C3.2 - 3.8 V
When engine coolant tem-
perature is 20_C2.3 - 2.9 V
When engine coolant tem-
perature is 40_C1.3 - 1.9 V
When engine coolant tem-
perature is 80_C0.3 - 0.9 V
45Crank angle sensorEngine: Cranking0.4 - 4.0 V
Engine: Idling1.5 - 2.5 V
46Power supply voltage
applied to accelerator
pedal position sensor
(1st channel)Ignition switch: ON4.5 - 5.5 V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Injector13A-238
NOTE
When removing the fuel pump (high pressure), air may
get into the fuel pump (high pressure). If air gets into
the fuel pump (high pressure), diagnosis code No.56 for
abnormal fuel pressure will be output.
2. Use the MUT-IIto check the diagnosis code. If the
diagnosis code No.56 for fuel pressure sensor system
defect is output, erase it.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Fuel Pump (High Pressure)13A-241
"
CA
O-RING/FUEL PRESSURE HOSE INSTALLATION
1. Apply a small amount of fresh engine oil to the O-ring.
Caution
Take care not to let any of the engine oil get inside
the fuel pump (high pressure) or the delivery pipe
assembly.
2. While being careful not to damage the O-ring, turn the
fuel pressure hose to the left and right and connect it
to the delivery pipe assembly. After connecting, check
that the fuel injector turns smoothly.
3. If the fuel pressure hose does not turn smoothly, the cause
may be that the O-ring is getting caught. Remove the fuel
pressure hose, check the O-ring for damage and
re-connect the fuel pressure hose to the delivery pipe
assembly and then re-check.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

13B-1
DIESEL FUEL
<4D5>
CONTENTS
GENERAL INFORMATION 2..................
SERVICE SPECIFICATIONS 2.................
SPECIAL TOOL 2............................
ON-VEHICLE SERVICE 2.....................
Fuel Injection Timing Check and Adjustment 2...
Engine Idle Speed Check and Adjustment 2......
Evacuation of Water from Fuel Filter 2..........Evacuation of Air from Fuel Line 3..............
Fuel Filter Cartridge Replacement 3.............
Fuel Injection Pump Check 3...................
Boost Compensator Check 4....................
Injection Nozzle Check and Adjustment 4........INJECTION NOZZLE 6.......................
INJECTION PUMP 10........................


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk