AUTOMATIC TRANSMISSION -Troubleshooting 23-34 Code No. 42 2nd without completion of shiftingProbable cause If the output shaft speed sensor output multiplied by the 2nd gear ratio is not identical to the input shaft speed sensor output after shifting to 2nd, code No. 42 is output. If code No. 42 is output 4 times, the transmission is fixed in 3rd and the N range lampflashes at a rate of 1 Hz.DMalfunction of input shaft speed sensor DMalfunction of output shaft speed sensor DMalfunction of harness or connector DMalfunction of solenoid valve DMalfunction of reverse clutch retainer DMalfunction of direct planetary carrier DMalfunction of 2ND brake system DMalfunction of UD clutch system DMalfunction of RED brake system DMalfunction of one-way clutch system DMalfunction of engine-A/T-ECU <6G7> DMalfunction of A/T-ECU<4M4> DNoise is generated. LRefer to the Transmission Workshop Manual. Repair NO YES YES MUT- IISelf-Diag Code DIs code No. 22 output?Code No. 22 Input shaft speed sensor system check (Refer to P.23-20.) OK NO Code No. 23 Output shaft speed sensor system check (Refer to P.23-22.)MUT- IIActuator Test DIs code No. 23 output? NG NGMUT- IIActuator Test DNo.1 LR solenoid valve DNo.2 UD solenoid valve DNo.3 2ND solenoid valve DNo.4 OD solenoid valve DNo.5 RED solenoid valve OK:The sound of operation should be heard.Replace the appropriate solenoid valve. L DCheck the harness between the input shaft speed sensor and the engine-A/T-ECU. <6G7> DCheck the harness between the input shaft speed sensor and the A/T-ECU.<4M4> Replace the input shaft speed sensor. LNG Check the trouble symptoms. Overhaul the A/T. L DReplace the reverse clutch retainer. Check the trouble symptoms. Eliminate the cause of the noise.To the nextpage Measure the output wave pattern of the input shaft speed sensor at engine-A/T-ECU connectors D-121 and D-122 <6G7>, or at A/T-ECU connector D-108<4M4>(using an oscilloscope). DVehicle speed: approx. 50 km/h DShift range: 4th <6G7> Voltage between No.81 (D-121) and No.103 (D-122) <4M4> Voltage between No.31(D-108) and No.43 (D-108) OK:A wave pattern such as the one shown on P.23-69 (Check Procedure Using an Oscilloscope) should be output, and the maximum value should be 4.8 V or more and the minimumvalue should be 0.8 V or less. There should be no noise in the output wave pattern. OKOK NG NG www.WorkshopManuals.co.uk Purchased from www.WorkshopManuals.co.uk
AUTOMATIC TRANSMISSION -Troubleshooting 23-35 NG Replace the valve body assembly. L Check the trouble symptoms. Replace the engine-A/T-ECU or A/T-ECU. Check the trouble symptoms. Repair OK NGDCheck the harness between the output shaft speed sensor and the engine-A/T-ECU. <6G7> DCheck the harness between the output shaft speed sensor and the A/T-ECU.<4M4> Replace the output shaft speed sensor. L OK Check the trouble symptoms. Overhaul the A/T. L DReplace the direct planetary carrier. Check the trouble symptoms. Eliminate the cause of the noise. From the previouspage Measure the output wave pattern of the output shaft speed sensor at engine-A/T-ECU connectors D-121 and D-122 <6G7>, or at A/T-ECU connector D-108<4M4>(using an oscilloscope). DVehicle speed: approx. 50 km/h DShift range: 4th <6G7> Voltage between No.81 (D-121) and No.104 (D-122) <4M4> Voltage between No.32(D-108) and No.43 (D-108) OK:A wave pattern such as the one shown on P.23-69 (Check Procedure Using an Oscilloscope) should be output, and the maximum value should be 4.8 V or more and the minimumvalue should be 0.8 V or less. There should be no noise in the output wave pattern. OK NG Overhaul the A/T. L DReplace the UD clutch. (Code No. 41, 43 or No. 44 is output, or no other codes are output.) DReplace the 2ND brake. (Code No. 44 or No. 45 is output, or no other codes are output.) DReplace the RED brake. (Code No. 41, 43 or No. 46 is output, or no other codes are output.) DReplace the one-way clutch (OWC-D). (Code No. 41 or No. 43 is output, or no other codes are output.)NG NG NG www.WorkshopManuals.co.uk Purchased from www.WorkshopManuals.co.uk
AUTOMATIC TRANSMISSION -Troubleshooting 23-36 Code No.43 3rd without completion of shiftingProbable cause If the output shaft speed sensor output multiplied by the 3rd gear ratio is not identical to the input shaft speed sensor output after shifting to 3rd, code No. 43 is output. If code No. 43 is output 4 times, the transmission is fixed in 3rd and the N range lampflashes at a rate of 1 Hz.DMalfunction of input shaft speed sensor DMalfunction of output shaft speed sensor DMalfunction of harness or connector DMalfunction of solenoid valve DMalfunction of reverse clutch retainer DMalfunction of direct planetary carrier DMalfunction of UD clutch system DMalfunction of OD clutch system DMalfunction of RED brake system DMalfunction of one-way clutch system DMalfunction of engine-A/T-ECU <6G7> DMalfunction of A/T-ECU<4M4> DNoise is generated. LRefer to the Transmission Workshop Manual. Repair NO YES YES MUT- IISelf-Diag Code DIs code No. 22 output?Code No. 22 Input shaft speed sensor system check (Refer to P.23-20.) OK NO Code No. 23 Output shaft speed sensor system check (Refer to P.23-22.)MUT- IIActuator Test DIs code No. 23 output? NG NGMUT- IIActuator Test DNo.1 LR solenoid valve DNo.2 UD solenoid valve DNo.3 2ND solenoid valve DNo.4 OD solenoid valve DNo.5 RED solenoid valve OK:The sound of operation should be heard.Replace the appropriate solenoid valve. L DCheck the harness between the input shaft speed sensor and the engine-A/T-ECU. <6G7> DCheck the harness between the input shaft speed sensor and the A/T-ECU.<4M4> Replace the input shaft speed sensor. LNG Check the trouble symptoms. Overhaul the A/T. L DReplace the reverse clutch retainer. Check the trouble symptoms. Eliminate the cause of the noise.To the nextpage Measure the output wave pattern of the input shaft speed sensor at engine-A/T-ECU connectors D-121 and D-122 <6G7>, or at A/T-ECU connector D-108<4M4>(using an oscilloscope). DVehicle speed: approx. 50 km/h DShift range: 4th <6G7> Voltage between No.81 (D-121) and No.103 (D-122) <4M4> Voltage between No.31(D-108) and No.43 (D-108) OK:A wave pattern such as the one shown on P.23-69 (Check Procedure Using an Oscilloscope) should be output, and the maximum value should be 4.8 V or more and the minimumvalue should be 0.8 V or less. There should be no noise in the output wave pattern. OKNG NG OK www.WorkshopManuals.co.uk Purchased from www.WorkshopManuals.co.uk
AUTOMATIC TRANSMISSION -Troubleshooting 23-37 NG Replace the valve body assembly. L Check the trouble symptoms. Replace the engine-A/T-ECU or A/T-ECU. Check the trouble symptoms. Repair OK NGDCheck the harness between the output shaft speed sensor and the engine-A/T-ECU. <6G7> DCheck the harness between the output shaft speed sensor and the A/T-ECU.<4M4> Replace the output shaft speed sensor. L OK Check the trouble symptoms. Overhaul the A/T. L DReplace the direct planetary carrier. Check the trouble symptoms. Eliminate the cause of the noise. To the nextpage Measure the output wave pattern of the output shaft speed sensor at engine-A/T-ECU connectors D-121 and D-122 <6G7>, or at A/T-ECU connector D-108<4M4>(using an oscilloscope). DVehicle speed: approx. 50 km/h DShift range: 4th <6G7>Voltage between No.81 (D-121) and No.104 (D-122) <4M4> Voltage between No.32(D-108) and No.43 (D-108) OK:A wave pattern such as the one shown on P.23-69 (Check Procedure Using an Oscilloscope) should be output, and with the maximum value should be 4.8 V or more and the minimumvalue should be 0.8 V or less. There should be no noise in the output wave pattern. OK NG Overhaul the A/T. L DReplace the UD clutch. (Code No. 41, 42 or No. 44 is output, or no other codes are output.) DReplace the OD clutch. (Code No. 44 or No. 45 is output, or no other codes are output.) DReplace the RED brake. (Code No. 41, 42 or No. 46 is output, or no other codes are output.) DReplace the one-way clutch (OWC-D). (Code No. 41 or No. 42 is output, or no other codes are output.)NG NG NG www.WorkshopManuals.co.uk Purchased from www.WorkshopManuals.co.uk
AUTOMATIC TRANSMISSION -Troubleshooting 23-38 Code No.44 4th without completion of shiftingProbable cause If the output shaft speed sensor output multiplied by the 4th gear ratio is not identical to the input shaft speed sensor output after shifting to 4th, code No. 44 is output. If code No. 44 is output 4 times, the transmission is fixed in 3rd and the N range lampflashes at a rate of 1 Hz.DMalfunction of input shaft speed sensor DMalfunction of output shaft speed sensor DMalfunction of harness or connector DMalfunction of solenoid valve DMalfunction of reverse clutch retainer DMalfunction of direct planetary carrier DMalfunction of UD clutch system DMalfunction of 2ND brake system DMalfunction of OD clutch system DMalfunction of DIR clutch system DMalfunction of engine-A/T-ECU <6G7> DMalfunction of A/T-ECU<4M4> DNoise is generated. LRefer to the Transmission Workshop Manual. Repair NO YES YES MUT- IISelf-Diag Code DIs code No. 22 output?Code No. 22 Input shaft speed sensor system check (Refer to P.23-20.) OK NO Code No. 23 Output shaft speed sensor system check (Refer to P.23-22.)MUT- IIActuator Test DIs code No. 23 output? NG NGMUT- IIActuator Test DNo.1 LR solenoid valve DNo.2 UD solenoid valve DNo.3 2ND solenoid valve DNo.4 OD solenoid valve DNo.5 RED solenoid valve OK:The sound of operation should be heard.Replace the appropriate solenoid valve. L DCheck the harness between the input shaft speed sensor and the engine-A/T-ECU. <6G7> DCheck the harness between the input shaft speed sensor and the A/T-ECU.<4M4> Replace the input shaft speed sensor. LNG Check the trouble symptoms. Overhaul the A/T. L DReplace the reverse clutch retainer. Check the trouble symptoms. Eliminate the cause of the noise.To the nextpage Measure the output wave pattern of the input shaft speed sensor at engine-A/T-ECU connectors D-121 and D-122 <6G7>, or at A/T-ECU connector D-108<4M4>(using an oscilloscope). DVehicle speed: approx. 50 km/h DShift range: 4th <6G7> Voltage between No.81 (D-121) and No.103 (D-122) <4M4> Voltage between No.31(D-108) and No.43 (D-108) OK:A wave pattern such as the one shown on P.23-69 (Check Procedure Using an Oscilloscope) should be output, and the maximum value should be 4.8 V or more and the minimumvalue should be 0.8 V or less. There should be no noise in the output wave pattern. OKOK NG NG www.WorkshopManuals.co.uk Purchased from www.WorkshopManuals.co.uk
AUTOMATIC TRANSMISSION -Troubleshooting 23-40 Code No.45 5th without completion of shiftingProbable cause If the output shaft speed sensor output multiplied by the 5th gear ratio is not identical to the input shaft speed sensor output after shifting to 5th, code No. 45 is output. If code No. 45 is output 4 times, the transmission is fixed in 3rd and the N range lampflashes at a rate of 1 Hz.DMalfunction of input shaft speed sensor DMalfunction of output shaft speed sensor DMalfunction of harness or connector DMalfunction of solenoid valve DMalfunction of reverse clutch retainer DMalfunction of direct planetary carrier DMalfunction of 2ND brake system DMalfunction of OD clutch system DMalfunction of DIR clutch system DMalfunction of engine-A/T-ECU <6G7> DMalfunction of A/T-ECU.<4M4> DNoise is generated. LRefer to the Transmission Workshop Manual. Repair NO YES YES MUT- IISelf-Diag Code DIs code No. 22 output?Code No. 22 Input shaft speed sensor system check (Refer to P.23-20.) OK NO Code No. 23 Output shaft speed sensor system check (Refer to P.23-22.)MUT- IIActuator Test DIs code No. 23 output? NG NGMUT- IIActuator Test DNo.1 LR solenoid valve DNo.2 UD solenoid valve DNo.3 2ND solenoid valve DNo.4 OD solenoid valve DNo.5 RED solenoid valve OK:The sound of operation should be heard.Replace the appropriate solenoid valve. L DCheck the harness between the input shaft speed sensor and the engine-A/T-ECU. <6G7> DCheck the harness between the input shaft speed sensor and the A/T-ECU.<4M4> Replace the input shaft speed sensor. LNG Check the trouble symptoms. Overhaul the A/T. L DReplace the reverse clutch retainer. Check the trouble symptoms. Eliminate the cause of the noise.To the nextpage Measure the output wave pattern of the input shaft speed sensor at engine-A/T-ECU connectors D-121 and D-122 <6G7>, or at A/T-ECU connector D-108<4M4>(using an oscilloscope). DVehicle speed: approx. 50 km/h DShift range: 4th <6G7> Voltage between No.81 (D-121) and No.103 (D-122) <4M4> Voltage between No.31(D-108) and No.43 (D-108) OK:A wave pattern such as the one shown on P.23-69 (Check Procedure Using an Oscilloscope) should be output, and the maximum value should be 4.8 V or more and the minimumvalue should be 0.8 V or less. There should be no noise in the output wave pattern. OKNG NG OK www.WorkshopManuals.co.uk Purchased from www.WorkshopManuals.co.uk
AUTOMATIC TRANSMISSION -Troubleshooting 23-41 NG Replace the valve body assembly. L Check the trouble symptoms. Replace the engine-A/T-ECU or A/T-ECU. Check the trouble symptoms. Repair OK NGDCheck the harness between the output shaft speed sensor and the engine-A/T-ECU. <6G7> DCheck the harness between the output shaft speed sensor and the A/T-ECU.<4M4> Replace the output shaft speed sensor. L OK Check the trouble symptoms. Overhaul the A/T. L DReplace the direct planetary carrier. Check the trouble symptoms. Eliminate the cause of the noise. From the previouspage Measure the output wave pattern of the output shaft speed sensor at engine-A/T-ECU connectors D-121 and D-122 <6G7>, or at A/T-ECU connector D-108<4M4>(using an oscilloscope). DVehicle speed: approx. 50 km/h DShift range: 4th <6G7> Voltage between No.81 (D-121) and No.104 (D-122) <4M4> Voltage between No.32(D-108) and No.43 (D-108) OK:A wave pattern such as the one shown on P.23-69 (Check Procedure Using an Oscilloscope) should be output, and the maximum value should be 4.8 V or more and the minimumvalue should be 0.8 V or less. There should be no noise in the output wave pattern. OK NG Overhaul the A/T. L DReplace the OD clutch. (Code No. 43 or No. 44 is output, or no other codes are output.) DReplace the 2ND brake. (Code No. 42 is output, or no other codes are output.) DReplace the DIR clutch. (Code No. 44 is output, or no other codes are output.)NG NG NG www.WorkshopManuals.co.uk Purchased from www.WorkshopManuals.co.uk
AUTOMATIC TRANSMISSION -Troubleshooting 23-42 Code No. 46 Reverse without completion of shiftingProbable cause If the output shaft speed sensor output multiplied by the reverse gear ratio is not identical to the input shaft speed sensor output after shifting to reverse, code No. 46 is output. If code No. 46 is output 4 times, the transmission is fixed in 3rd and the N range lampflashes at a rate of 1 Hz.DMalfunction of input shaft speed sensor DMalfunction of output shaft speed sensor DMalfunction of harness or connector DMalfunction of solenoid valve DMalfunction of reverse clutch retainer DMalfunction of direct planetary carrier DMalfunction of LR brake system DMalfunction of REV clutch system DMalfunction of RED clutch system DMalfunction of engine-A/T-ECU <6G7> DMalfunction of A/T-ECU<4M4> DNoise is generated. LRefer to the Transmission Workshop Manual. Repair NO YES YES MUT- IISelf-Diag Code DIs code No. 22 output?Code No. 22 Input shaft speed sensor system check (Refer to P.23-20.) OK NO Code No. 23 Output shaft speed sensor system check (Refer to P.23-22.)MUT- IIActuator Test DIs code No. 23 output? NG NGMUT- IIActuator Test DNo.1 LR solenoid valve DNo.2 UD solenoid valve DNo.3 2ND solenoid valve DNo.4 OD solenoid valve DNo.5 RED solenoid valve OK:The sound of operation should be heard.Replace the appropriate solenoid valve. L DCheck the harness between the input shaft speed sensor and the engine-A/T-ECU. <6G7> DCheck the harness between the input shaft speed sensor and the A/T-ECU.<4M4> Replace the input shaft speed sensor. LNG Check the trouble symptoms. Overhaul the A/T. L DReplace the reverse clutch retainer. Check the trouble symptoms. Eliminate the cause of the noise.To the nextpage Measure the output wave pattern of the input shaft speed sensor at engine-A/T-ECU connectors D-121 and D-122 <6G7>, or at A/T-ECU connector D-108<4M4>(using an oscilloscope). DVehicle speed: approx. 50 km/h DShift range: 4th <6G7> Voltage between No.81 (D-121) and No.103 (D-122) <4M4> Voltage between No.31(D-108) and No.43 (D-108) OK:A wave pattern such as the one shown on P.23-69 (Check Procedure Using an Oscilloscope) should be output, and the maximum value should be 4.8 V or more and the minimumvalue should be 0.8 V or less. There should be no noise in the output wave pattern. OKOK NG NG www.WorkshopManuals.co.uk Purchased from www.WorkshopManuals.co.uk
