2000 MITSUBISHI MONTERO sport mode

MITSUBISHI SC-Troubleshooting13E-15
DATA LIST REFERENCE TABLE
The following ECU input data items can be read using the MUT-
II.
Item
No.Check itemInspection conditionsNormal condition
10Vehicle speedWhen vehicle is being drivenSpeedometer display and
MUT-IIdisplay are identical.
11AcceleratorIgnition switch:Release the accelerator pedal.0.9 - 1.1 V
pedal position
sensorONDepress the accelerator pedal gradually.Increases in response to
pedal depression stroke.
Depress the accelerator pedal fully4.0 V or more
18Power supply
voltageIgnition switch: ONSystem voltage
19Accelerator
pedal positionIgnition switch:
ONRelease the accelerator pedalON
pedal position
switch (Idle
switch)ON
Depress the accelerator pedal slightly.OFF
20Ignition switchIgnition switch: ONON
Ignition switch: OFFOFF
22Front-right
wheel speedWhen vehicle is being drivenSpeedometer display and
MUT-IIdisplay are identical.
28Engine typeVehicles with the 6G74 engine6G74
Vehicles with the 4M41 engine4M41
30Trace controlSC system control is activeON
SC system control is not activeOFF
31Engine specifi-Vehicles with the 6G74 engineDOHC
cation 1Vehicles with the 4M41 engine-
32Engine specifi-Vehicles with the 6G74 engineN/A
cation 2Vehicles with the 4M41 engine-
33Engine specifi-Vehicles with the 6G74 engineMIVEC/ETV
cation 3Vehicles with the 4M41 engine-
35Destination-EC
40Engine speedDepress the accelerator pedal gradually.Tachometer display and
MUT-IIdisplay are identical.
51Inhibitor switchIgnition switch:Selector lever position: PP
ONSelector lever position: RREngine:
stopped
Selector lever position: NN
Selector lever position: DD
52Shift positionSelector lever
position: sportsDriving at a constant speed of 10 km/h in
1st1st
modeDriving at a constant speed of 30 km/h in
2nd2nd
Driving at a constant speed of 50 km/h in
3rd3rd
Driving at a constant speed of 50 km/h in
4th4th
Driving at a constant speed of 70 km/h in
5th5th


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting AUTOMATIC TRANSMISSION -Troubleshooting 23-5
ROAD TEST
No.Pre-test/opera-
tion conditionsTest/operationJudgment valueCheck itemDiag-
nosis
code
No.Inspection pro-
cedure if there is
an abnormality
1Ignition switch:
OFFIgnition switch
(1) ONData List No. 54
(1) 10 - 12 VA/T control
relay54A/T control relay
system
2Ignition switch:
ON
Engine:Stop
Selector lever
position: PSelector lever posi-
tion
(1) P
(2) R
(3) N
(4) DData List No. 61
(1) P
(2) R
(3) N
(4) DInhibitor
switch-Inhibitor switch
system
Selector lever opera-
tion
(1) D (1st)
(2) Sports mode se-
lected (1st)
(3) Lever moved toData List
No.67 No.68 No.69
(1)OFF OFF OFF
(2)ON OFF OFF
(3)ON ON OFF
(4)ON OFF ON
Select switch
Upshift
switch
Downshift
switch-Sports mode
switch system
upshift position
and held (2nd)
(4) Lever moved to
downshift
position and held
(1st)Shift indicator lamp
(1) D and 1
illuminate
(2) Only 1
illuminates
(3) Only 2
illuminates
(4) Only 1
illuminates
Accelerator pedal
(1) Fully closed
(2) Depressed
(3) Fully openedData List No. 11
(1) 985 - 1,085 mV
(2) Gradually in-
creases from (1)
(3) 4,000 mV or
moreAPS11
12
14APS system
Data list No.25
(1) OFF
(2) ONWide open
throttle
switch25Wide open
throttle switch
system
2Ignition switch:
ON
Engine: StopBrake pedal
(1) Depressed
(2) ReleasedData List No. 26
(1) ON
(2) OFFStop lamp
switch26Stop lamp
switch system
Selector lever
position: PTransfer shift lever
position
(1) Except for 4LLc
(2) 4LLcData List No. 75
(1) OFF
(2) ON4LLc switch-4LLc switch sys-
tem


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-7
No.Inspection pro-
cedure if there is
an abnormality Diag-
nosis
code
No. Check item Judgment value Test/operation Pre-test/opera-
tion conditions
6Selector lever
position:
Sports mode
(Must be done on
a level and
straight road.)Selector lever posi-
tion and engine
(1) Idling in 1st
(Vehicle
stopped)
(2) Driving at aData List No. 63
(2) 1st
(3) 2nd
(4) 3rd
(5) 4th
(6) 5thShift condi-
tion--
constant speed
of 10 km/h in 1st
(3) Driving at a
constant speed
of 30 km/h in 2nd
(4) Driving at a
constant speedData List No. 31
(2) 0%
(3) 100%
(4) 100%
(5) 100%
(6) 100%Low & re-
verse sole-
noid valve
(LR solenoid
valve)31LR solenoid
valve system
constant speed
of 50 km/h in 3rd
(5) Driving at a
constant speed
of 50 km/h in 4th
(6) Driving at a
constant speed
Data List No. 32
(2) 0%
(3) 0%
(4) 0%
(5) 0%
(6) 100%Underdrive
solenoid
valve (UD
solenoid
valve)32UD solenoid
valve system
of 70 km/h in 5th
(Each condition
should be main-
tained for 10 seconds
or more)
Data List No. 33
(2) 100%
(3) 0%
(4) 100%
(5) 100%
(6) 0%Second sole-
noid valve
(2ND sole-
noid valve)332nd solenoid
valve system
Data List No. 34
(2) 100% (5) 0%
(3) 100% (6) 0%
(4) 0%Overdrive
solenoid
valve (OD
solenoid
valve)34OD solenoid
valve system
Data List No. 35
(2) 0% (5) 100%
(3) 0% (6) 100%
(4) 0%Reduction
solenoid
valve (RED
solenoid
valve)35RED solenoid
valve system
Data List No. 29
(1) 0 km/h
(5) 50 km/hVehicle
speed sen-
sor-Vehicle speed
sensor system
Data List No. 22
(5) 1,300 - 1,600
r/minInput shaft
speed sen-
sor22Input shaft
speed sensor
system
Data List No. 23
(5) 1,300 - 1,600
r/minOutput shaft
speed sen-
sor23Output shaft
sensor system
Selector lever posi-
tion and engine
(1) Driving at 30
km/h in 2 range,Data List No. 36
(1) 70% - 90% to
0%
(2) 70% - 90%Damper
clutch con-
trol solenoid
valve (DCC36
52DCC solenoid
valve system
then fully close
the accelerator.
(2) Driving at a
constant speed
of 50 km/h in 4thData List No. 52
(1) - 300 - - 100
r/min or 100 -
300 r/min
(2) - 10 - 10 r/minsolenoid
valve)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-8
No.Inspection pro-
cedure if there is
an abnormality Diag-
nosis
code
No. Check item Judgment value Test/operation Pre-test/opera-
tion conditions
7Suspends the
INVECS-IIfunc-Use the MUT-IIto
monitor data list Nos.For (1), (2) and (3),
the output shaftProblem dur-
ing shifting-Shocks, engine
racing
tion using MUT-II11, 23 and 63.speed (vehicleIncorrect-All pointsSelector level
position:D(1) Accelerate to 5th
gear at an APSspeed) should be
identical, and thereshift points-Some points
(Must be done on
a level andgear at an APS
output of 1.5 V
(opening angleshould be no abnor-
mal shocks. For (4),No shifting-No diagnosis
codes
straight road.)30%).
(2) Slowly deceler-
ate and stop.(5) and (6), down-
shifting should occur
immediately after
22Input shaft speed
sensor system
ate and stop.
(3) Accelerate to 5th
gear at an APSthe operation is car-
ried out.23Output shaft sen-
sor system
output of 2.5 V
(opening angle
50%).No shifting
from 1st to31LR solenoid
valve system
50%).
(4) At 60 km/h in 5th,
select Sports2nd, or no
shifting from332nd solenoid
valve system
mode and shift
down to 4th.
(5) At 40 km/h in 4th,
select Sports2nd to 1st411st without
completion of
shifting
select Sports
mode and shift
down to 3rd.
(6) At 20 km/h in 3rd,
422nd without
completion of
shifting
shift down to 2nd.
(7) At 20 km/h in
2nd, shift downNo shifting
from 2nd to332nd solenoid
valve system
2nd, shift down
to 1st.3rd, or no
shifting from34OD solenoid
valve system
3rd to 2nd422nd without
completion of
shifting
433rd without
completion of
shifting
No shifting
from 3rd to31LR solenoid
valve system
4th, or no
shifting from35RED solenoid
valve system
4th to 3rd433rd without
completion of
shifting
444th without
completion of
shifting
No shifting
from 4th to32UD solenoid
valve system
5th, or no
shifting from332nd solenoid
valve system
5th to 4th444th without
completion of
shifting
455th without
completion of
shifting


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-20
Code No. 22 Input shaft speed sensor systemProbable cause
If no output pulse from the input shaft speed sensor is detected for 1 second or
more while the vehicle is driving at 30 km/h or more in 4th, it isjudged that
there is a short-circuit oropencircuit in the input shaft speed sensor, and code
No. 22 is output.
If code No. 22 is output 4 times, the transmission is locked at 3rd gear (D) or
2nd gear (downshift operation in Sports mode) as a fail-safe measure, and the N
range indicator lampflashes at 1 Hz.DMalfunction of input shaft speed sensor
DMalfunction of reverse clutch retainer
DMalfunction of harness or connector
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
Transient malfunction
(Refer to GROUP 00 - Points to
Note for Transient Malfunctions.)
OK NG
Check the following connectors:
<6G7> D-121,<4M4>D-108
To the nextpage
NG
OKNG
NG
RepairCheck the following connectors:
<6G7> D-122,<4M4>D-108
Replace the engine-A/T-ECU or
A/T-ECU.
OKMUT-
IIData List
DNo. 22 Input shaft speed sensor
OK:Refer to P.23-61 (Data List
Chart).
Repair
OK
NG
NG
Check the trouble symptoms.
OK
Measure at engine-A/T-ECU
connector D-121 <6G7>, or at
A/T-ECU connector D-107 <4M4>.
DMeasure at the ECU terminals
DIgnition switch: ON
D<6G7> Voltage between terminal
81 and earth
D<4M4> Voltage between terminal
43 and earth
OK:0.5 V or less
Replace the engine-A/T-ECU or
A/T-ECU. NGCheck the trouble symptoms.
NG
Check the trouble symptoms.
Check the following connectors:
<6G7> D-121, D-122,<4M4>D-108
Replace the engine-A/T-ECU or
A/T-ECU.
OK
OK
Measure at engine-A/T-ECU
connector D-122 <6G7>, or at
A/T-ECU connector D-108 <4M4>.
DMeasure at the ECU terminals
DDisconnect C-23
DIgnition switch: ON
D<6G7> Voltage between terminal
103 and earth
D<4M4> Voltage between terminal
31 and earth
OK:4.8 - 5.2 V
Measure the output wave pattern of
the input shaft speed sensor at
engine-A/T-ECU connectors D-121
and D-122 <6G7>, or at A/T-ECU
connector D-108<4M4>(using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 4th
D<6G7> Voltage between terminal
81 of D-121 and terminal 103 of
D-122
D<4M4> Voltage between terminal
31 of D-108 and terminal 43 of
D-108
OK:A wave pattern such as the
one shown on P.23-69
(Check Procedure Using an
Oscilloscope) should be
output, and the maximum
value should be 4.8 V or
more and the minimumval-
ue should be 0.8 V or less.
There should be no noise
in the output wave pattern.NG
NG
Repair


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-22
Code No. 23 Output shaft speed sensor systemProbable cause
If the output from the output shaft speed sensor is 50% or less continuously for
1 second or more while the vehicle is driving at 30 km/h or more in 4th, it is
judged that there is ashort-circuit oropencircuit in the output shaft speed
sensor, and code No. 23 is output.
If code No. 23 is output 4 times, the transmission is locked at 3rd gear (D) or
2nd gear (downshift operation in Sports mode) as a fail-safe measure, and the N
range indicator lampflashes at 1 Hz.DMalfunction of output shaft speed sensor
DMalfunction of direct planetary carrier
DMalfunction of harness or connector
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
NG
Repair
NG
Transient malfunction
(Refer to GROUP 00 - Points to
Note for Transient Malfunctions.)
OK NG
Check the following connectors:
<6G7> D-122,<4M4>D-108
To the nextpage
NG
OK
NG
RepairCheck the following connectors:
<6G7> D-122,<4M4>D-108
Replace the engine-A/T-ECU or
A/T-ECU.
OKMUT-
IIData List
DNo. 23 Output shaft speed
sensor system
OK:Refer to P.23-61 (Data List
Chart).
Repair
OK
OK
NG
Check the trouble symptoms.
OK
Measure at engine-A/T-ECU
connector D-121 <6G7>, or at
A/T-ECU connector D-107 <4M4>.
DMeasure at the ECU terminals
DIgnition switch: ON
D<6G7>Voltage between terminals
81 and earth
D<4M4> Voltage between terminal
43 and earth
OK:0.5 V or less
Replace the engine-A/T-ECU or
A/T-ECU. NGCheck the trouble symptoms.
NG
Check the trouble symptoms.
Check the following connectors:
<6G7> D-121, D-122,<4M4>D-108
Replace the engine-A/T-ECU or
A/T-ECU.
OK
Measure at engine-A/T-ECU
connector D-122 <6G7>, or at
A/T-ECU connector D-108 <4M4>.
DMeasure at the ECU terminals
DDisconnect C-02
DIgnition switch: ON
D<6G7>Voltage between terminals
104 and earth
D<4M4> Voltage between terminal
32 and earth
OK:4.8 - 5.2 VNG
Measure the output wave pattern of
the output shaft speed sensor at
engine-A/T-ECU connectors D-121
and D-122 <6G7>, or at A/T-ECU
connector D-108<4M4>(using an
oscilloscope).
DVehicle speed: approx. 50 km/h
DShift range: 4th
D<6G7> Voltage between terminal
81 of D-121 and terminal 104 of
D-122
D<4M4> Voltage between terminal
32 of D-108 and terminal 43 of
D-108
OK:A wave pattern such as the
one shown on P.23-69
(Check Procedure Using an
Oscilloscope) should be
output, and the maximum
value should be 4.8 V or
more and the minimumval-
ue should be 0.8 V or less.
There should be no noise
in the output wave pattern.NG
Repair
NG


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-49
Inspection procedure 2
Starting not possible
Probable cause
If the enginewill not start when the selector lever is at the P or N position, the
cause is probably a malfunction of the inhibitor switch system, the transmission
control cable assembly, theenginesystem, the torque converter or the oil pump.DMalfunction of inhibitor switch system
DMalfunction of transmission control cable assembly
DMalfunction of enginesystem
DMalfunction of torque converter
DMalfunction of oil pump
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
NG
Inspection Procedure 16: Inhibitor switch system check (Refer
to P.23-58.)NG
Repair or replace
OK
Torque converter check
DCheck for incorrect installation (inserted at an angle, etc.)
or damagedsplines.NGIf repair is possible, repair the damaged part.
If repair is not possible because the splines aredamaged,
replace the torque converter assembly.
OK
Replace the oil pumpassembly.
L
(The oilpump cannot be disassembled.)
Engine system check
DControl system, ignition system, fuel system, vehicle bodyNG
Repair
OK
Transmission control cable assembly checkNG
Repair OK
Check the trouble symptoms.Replace the engine-A/T-ECU or A/T-ECU.
Inspection procedure 3
Does not move forward
Probable cause
If the vehicle does not move forward when theengine is idling and theselector
lever is moved from N to D, 3, 2 or L, or if it is shifted to 1st or 2nd in Sports
mode, the cause is probably a problem with line pressure, or a malfunction of
the UD clutch or valve body.DAbnormal line pressure
DMalfunction of UD solenoid valve
DMalfunction of UD clutch system
DMalfunction of valve body
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
MUT-
IIActuator Test
DNo.2 UD solenoid valve
OK:Sound of operation can be heardNGReplace the solenoid valve.
L
OK
Fluid pressure test (Refer to P.23-106.)
DMeasure the fluid pressure at each element in 1st in
Sportsmode
Standard value:Refer to P.23-106.NGDisassemble, clean and re-assemble the valve body.
L
DMake sure that the mounting bolts are not loose and that
the O-ring and valve body are notdamaged or positioned
incorrectly.
DIf the extent of thedamagelooks too bad for repairs to be
carried out, replace the valve body assembly.
OK
UD clutch system check
DRemove the transmission assembly, the valve body cover
and the valve body.
DBlow air through the UD clutch oilhole in the transmission
case, and check that the piston operates to maintain
pressure.
UD clutch check
L
DCheck for a problem such as burnt facing, poor piston
sealing or interference with the retainer.OKCheck the trouble symptoms. NG
Replace the engine-A/T-ECU or A/T-ECU.NG


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-61
DATA LIST REFERENCE TABLE
Data
list No.Check itemInspection conditionsNormal condition
11APSIgnition switch: ON
Engine: StoppedAccelerator pedal:
Fully closed985 - 1085 mV
Engine: Stopped
Selector lever posi-
tion: P
Accelerator pedal:
DepressedGradually increases from the above
value.
Accelerator pedal:
Fully open4000 mV or higher
15A/T fluid tempera-
ture sensorDriving after en-
gine has warmed
upDrive for 15 minutes
or more until the ATF
temperature reaches
70 - 80°C.Gradually increases to 70 - 80°C.
21Crank angle sen-
sor <6G7>Engine: Idling
Selector lever posi-Compare the engine
speeds displayed onIdentical
sor <6G7>
Engine speed sen-
sor <4M4>Selector lever posi-
tion: Pspeeds displayed on
the tachometer and
the MUT-II.
22Input shaft speed
sensorShift range: 4thDriving at a constant
speed of 50 km/h in
4th1300 - 1600 r/min
23Output shaft speed
sensorShift range: 4thDriving at a constant
speed of 50 km/h in
4th1300 - 1600 r/min
25Wide open throttleAccelerator pedalReleasedOFF
switchpositionDepressedON
26Stop lamp switchIgnition switch: ON
Engine: StoppedBrake pedal: De-
pressedON
Engine: Stopped
Brake pedal: Re-
leasedOFF
29Vehicle speed sen-
sorSelector lever posi-
tion: Sports modeIdling in 1st
(Vehicle stopped)0 km/h
Driving at a constant
speed of 50 km/h in
3rd50 km/h
31LR solenoid valve
duty ratioSelector lever posi-
tion: Sports modeData List No.No. 31No. 32No. 33No. 34No.35
32UD solenoid valve
duty ratioDriving at a constant
speed in 1st0%0%100%100%0%
332nd solenoid valve
duty ratioDriving at a constant
speed in 2nd100%0%0%100%0%
34OD solenoid valve
duty ratioDriving at a constant
speed in 3rd100%0%100%0%0%
35RED solenoid
valve duty ratioDriving at a constant
speed in 4th0%0%100%0%100%
Driving at a constant
speed in 5th100%100%0%0%100%


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk