Page 1635 of 1839
CHASSIS ELECTRICAL -Clock or Center Display54A-65
INSPECTION PROCEDURE 6
The display screen is dim.
NOMeasure at center display unit connec-
tor D-03.
DDisconnect the connector.
DVoltage between terminal 24 and
body earth.
OK:0 V (Lighting switch: off)
System voltage (Lighting
switch: ON)NGRepair the fuse and wiring harness.
Is the brightness of the center display
set correctly?NOAdjust the brightness of display on set-
ting mode.
OK
Replace the center display unit.
OK
Replace the center display unit.
YES
Measure at center display unit connec-
tor D-03.
DDisconnect the connector.
DRheostat: max
DVoltage between terminal 32 and
body earth.
OK:Low voltage (0 - 3 V)NGRepair the wiring harness.
Does the brightness of display change
when the lighting switch is on or off?
YES
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1636 of 1839
CHASSIS ELECTRICAL -Clock or Center Display54A-66
INSPECTION PROCEDURE 7
Air conditioning display is not available.
Measure at center display unit connec-
tor D-03.
DDisconnect the connector.
DVoltage between terminal 36 and
body earth.
OK:System voltage (Ignition
switch: ON)
0 - 1 V (Ignition switch:
OFF)NGCheck the wiring harness between the
center display unit and the junction
block, and repair if necessary.
OK
NO OK
Check theaudio unit.
NG
NG
Repair wiring harness.
OK
OK
Replace the center display unit.
YES
Replace the A/C-ECU.
YES
Refer to GROUP 55 - A/C troubleshoot-
ing.Check the reoccurrence of symptom.OKEND
NG
Replace the center display unit.
Measure at center display unit connec-
tor D-04.
DDisconnect the connector.
DVoltage between terminal 9 and
body earth.
DVoltage between terminal 10 and
body earth.
DVoltage between terminal 19 and
body earth.
OK:Hi:4–5V
Lo:0–1V
Check the the wiring harnesses:
DBetween the center display and
A/C-ECU D-04, D-49
DBetween the center display and
AUDIO D-04, D-49
Check the reoccurrence of symptom.Select “Check of units connected into
the center display” on the service mode.
Does the symbol “AU” appear?
MUT-
IISelf-Diag code
Is the diagnosis code for A/C set?NG
NO
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1678 of 1839
CHASSIS ELECTRICAL -RV Meter54A-17
Termi-Input/out-
t
Signal sym-
bl
Terminal
lt
Harness problemTrouble symptoms when there is a
hblnal No.
p
put
gy
bolvoltage
(V)Open
circuitshort-cir-
cuit
yp
harness problem
11 - 1 4––––––
15Input/out-
putK (engine
K-LINE
signal)Hi: Sys-
tem volt-
age
Lo:0 - 1ExistsExistsDWiring communication error
DCommunication between the
engine-A/T-ECU
hicles> is not possible.
DAbnormal driving information
numerical display
16––––––
17Input/out-
putM-BUSY
(AUDIO)Hi:System
voltage
Lo:0 - 1ExistsExistsDAudio information does not
appear on the screen.
18–SHIELD-
EARTH
(AUDIO)––––
19Input/out-
putM-BUSY
(A/C)Hi:System
voltage
Lo:0 - 1ExistsExistsDAir conditioner information does
not appear on the screen.
DAmbient temperature is not
displayed.
20–SHIELD-
EARTH––––
22 - 21––––––
23InputAmbient
temperature
sensor–ExistsExistsDAmbient temperature is not
displayed.
24InputILL + (Light-
ing switch)Hi:System
voltage
Lo:0 - 1ExistsExistsDoes not illuminate.
25InputACC (ACC
power sup-
l)
System
voltageExists–Screen does not appear. No
operations are possible.
pp
ply)
g
–ExistsBlown multi-purpose fuse
26Input+BSystem
voltageExists–Screen does not appear. No
operations are possible.
g
–ExistsBlown multi-purpose fuse
27InputVSS (Vehicle
speed pulse
signal)Hi:System
voltage
Lo:0 - 1ExistsExistsDAbnormal “Distance km after
replacement” display in mainte-
nance screen
DSwitches which are not
supposed to operate during
driving do operate.
(Example:clock adjustment
screen, maintenance settings,
etc.)
DAmbient temperature display is
abnormally high.
28–Earth–Exists–Screen does not appear.
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1679 of 1839
CHASSIS ELECTRICAL -RV MeterCHASSIS ELECTRICAL -RV MeterCHASSIS ELECTRICAL -RV Meter54A-18
Termi-Input/out-
t
Signal sym-
bl
Terminal
lt
Harness problemTrouble symptoms when there is a
hblnal No.
p
put
gy
bolvoltage
(V)Open
circuitshort-cir-
cuit
yp
harness problem
29 - 30––––––
31–EARTH
(TEMP)––––
32–ILL - (illumi-
nation lamp
adjustment
signal)–ExistsExistsUnable to adjust illumination lamp
33InputFUEL
GAUGE0-3ExistsExists–
34 - 36––––––
CHART CLASSIFIED BY TROUBLE SYMPTOMS
Related unitTrouble SymptomInspection
procedure
No.Refer-
ence
page
Malfunction of RV meterNo system operations can be carried out.154A-18
System voltage drop warning screen appears.254A-18
Ambient temperature does not display normally.354A-19
Compass does not display normally.454A-20
Altimeter does not display normally.554A-21
Air conditioner information does not display normally.654A-21
Audio information does not display normally.754A-22
INSPECTION PROCEDURES FOR EACH TROUBLE SYMPTOM
Inspection procedure 1
No system operations can be carried out.
NG
OK
Check the following connectors:
D-27, D-223, D-31, D-39
D - 27, D - 33, D - 39Repair
Check the trouble symptoms.NGReplace the RV meter.
Inspection procedure 2
System voltage abnormality screen appears.
NOEnd
OK YES
Replace the battery.
Replace the RV meter.
NG
Does the voltage abnormality screen appear immediately
after the ignition switch is turned to the ACC position?
Malfunction of RV meter voltage judgment circuitMeasure at RV meter connector D-39.
DConnector disconnected
DVoltage between terminal (25) and body earth
OK:System voltage
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1680 of 1839
CHASSIS ELECTRICAL -RV Meter54A-19
Inspection procedure 3
Ambient temperature does not display normally.
OK
Ambient temperature sensor check
(Refer to GROUP 55B.)
NG
MUT-II diagnosis code
Is A/C diagnosis code No. 13 or No.
14 output?
Repair
Replace the RV meter. NG
Check the harness between the
A/C-ECU and the RV meter, and
repair if necessary.
Carry out a service function wiring
check.
Is the M-BUS signal normal?
YESNO
Replace the RV meter. NGNO
OK
Measure at RV meter connector D-39.
DConnector disconnected
DVoltage between terminal (27) and
body earth
OK:Hi: System voltage
Lo: 0 - 1 V
YES
Check the harness between the RV
meter and the vehicle speed sensor,
and repair if necessary.
Check the following connec-
tors:D-40, D-131
Carry out a service function wiring
check.
Is the SWS signal normal?Check the harness between the RV
meter and the ETACS-ECU, and
repair if necessary.NGMeasure at RV meter connector D-40.
DConnector disconnected
DVoltage between terminal (9) and
body earth
DVoltage between terminal (10) and
body earth
DVoltage between terminal (19) and
body earth
OK:Hi: 4 - 5 V
Lo: 0 - 1 V
OK
OK
Ambient temperature sensor check
(Refer to GROUP 55A.)
NGReplaceCarry out a service function wiring
check.
Is the ambient temperature sensor
signal normal?
YESNO
Replace the RV meter. NGNO
OKMeasure at RV meter connector D-39.
DConnector disconnected
DVoltage between terminal (27) and
body earth
OK:Hi: System voltage
Lo: 0 - 1 V
YES
Check the harness between the RV
meter and the vehicle speed sensor,
and repair if necessary.
Check the following connectors:
A - 30, D-27, D - 39
Carry out a service function wiring
check.
Is the SWS signal normal?Check the harness between the RV
meter and the ETACS-ECU, and repair if
necessary.
OK
NO
Repair
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1681 of 1839
CHASSIS ELECTRICAL -RV Meter54A-20
Inspection procedure 4
Compass does not display normally.
NO
NO
NG
Replace the RV meter.
Is a carrier antenna with a magnet
installed to the vehicle, or is there a
magnet or other metal near the RV
meter?YES
YES
YESEnd (NO abnormality)
NO
YESEnd (NO abnormality)Does operation return to normal
when the magnet or metal is
removed?
NO
Carry out a geomagnetic sensor
mode check in service mode. Does
operation return to normal if
degaussing or calibration is carried
out?OKEnd (NO abnormality)
Does the location have stable
geomagnetism?Is operation normal when the vehicle
is moved to a location with stable
geomagnetism?
OKEnd (NO abnormality)Carry out a geomagnetic sensor
mode check in service mode.
NG
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1682 of 1839
CHASSIS ELECTRICAL -RV Meter54A-21
Inspection procedure 5
Altimeter does not display normally.
NG
Replace the RV meter.
OKEnd (No abnormality)Carry out an altitude calibration mode check in service
mode.
Inspection procedure 6
Air conditioner information does not display normally.
NG
Replace the RV meter.
NG
Replace the RV meter.
(1)
Check the trouble symptoms. NO
MUT-II Self-diag code
Is A/C diagnosis code output?
Carry out a service function
communication and wiring check. One
of the following M-BUS outputs will
appear.
(1) E1 (Communication error)
(2) E2 (Open circuit or short-circuit)
(3) OKMeasure the wave pattern at RV meter
connector D-40.
DConnector disconnected
DVoltage between terminal (9) and
body earth
DVoltage between terminal (10) and
body earth
DVoltage between terminal (19) and
body earth
OK:Hi: 4 - 5 V
Lo: 0 - 1 V
Malfunction of A/C-ECU OKMeasure the wave pattern at A/C-ECU
connector D-131.
DConnector disconnected
DVoltage between terminal (6) and
body earth
DVoltage between terminal (16) and
body earth
DVoltage between terminal (17) and
body earth
OK:Hi: 4 - 5 V
Lo: 0 - 1 V (2)Check the following
connectors:D-40, D-131
NG
OK
Check the harness between
the RV meter and the
A/C-ECU, and repair if
necessary. (3)
Refer to GROUP 55B - A/C
Troubleshooting.YES
OK
Repair
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
Page 1683 of 1839
CHASSIS ELECTRICAL -RV Meter54A-22
Inspection procedure 7
Audio information does not display normally.
Replace the RV meter.
NG
Replace the radio and tape, CD
player
(1)
Check the trouble symptoms.
Carry out a service function
communication and wiring check. One
of the following M-BUS outputs will
appear.
(1) E1 (Communication error)
(2) E2 (Open circuit or short-circuit)
(3) OKMeasure the wave pattern at RV meter
connector D-40.
DConnector disconnected
DVoltage between terminal (7) and
body earth
DVoltage between terminal (8) and
body earth
DVoltage between terminal (17) and
body earth
OK:Hi: 4 - 5 V
Lo: 0 - 1 V
Malfunction of radio and tape, CD
player OK
(2)
Check the harness between the RV
meter and the radio and tape, CD player,
and repair if necessary. (3)
YESOK
NG
Is error message “004” shown?NOReplace the RV meter.
NOTE:
The contents of error messages shown in the audio display screen are as follows:
Error messageLocation and cause of malfunction
EJECTA magazine for CD changeris not inserted.
NO DISCCD is not inserted.
ERROR 001Program error in audio
ERROR 002Error in CD disk
ERROR 003Mechanical error in audio system
ERROR 004Communication error in audio systemand RV meter,power supply error in audio
system, and other errors
ERROR HOTHeat protection for audio system
www.WorkshopManuals.co.uk
Purchased from www.WorkshopManuals.co.uk
