2000 LEXUS GS400 Service Repair Manual

B01982
LEXUS
Hand±Held
Tester
B01879
Ohmmeter54
B01880
5
4 Battery
± SFI (2JZ±GE)FUEL PUMP
SF±7
1473 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(f) Connect a LEXUS hand±held tester to the DLC3.
(See step 1 in check fuel pump operation (a) to (e))
(g) Measure the fuel pressure.
Fuel pressure:
304 ± 343 kPa (3.1 ± 3.5 kgf/cm
2, 44 ± 50 psi)
If pressure is high, replace the fuel pressure regulator.
If pressure is low, check the fuel hoses and connections, fuel
pump, fuel filter and fuel pressure regulator.
(h) Disconnect the LEXUS hand±held tester from the DLC3.
(i) Start the engine.
(j) Measure the fuel pressure at idle.
Fuel pressure:
304 ± 343 kPa (3.1 ± 3.5 kgf/cm
2, 44 ± 50 psi)
(k) Stop the engine.
(l) Check that the fuel pressure remains as specified for 5
minutes after the engine has stopped.
Fuel pressure: 147 kPa (1.5 kgf/cm
2, 21 psi) or more
If pressure is not as specified, check the fuel pump, pressure
regulator and/or injectors.
(m) After checking fuel pressure, disconnect the negative (±)
terminal cable from the battery and carefully remove SST
to prevent gasoline from splashing.
SST 09268±45014
(n) Reconnect the fuel inlet hose to the fuel pipe support with
2 new gaskets and the union bolt.
Torque: 29 N´m (300 kgf´cm, 21 ft´lbf)
(o) Reconnect the negative (±) terminal cable to the battery.
(p) Check for fuel leaks.
3. INSPECT FUEL PUMP
(a) Remove the rear seat cushion.
(b) Remove the 3 cap nuts and floor service hole cover.
(c) Disconnect the fuel pump & sender gauge connector.
(d) Using an ohmmeter, measure the resistance between ter-
minals 4 and 5.
Resistance: 0.2 ± 3.0 W at 20°C (68°F)
If the resistance is not as specified, replace the fuel pump.
(e) Inspect the fuel pump operation.
Connect the positive (+) lead from the battery to terminal
4 of the connector, and the negative (±) lead to terminal
5. Check that the fuel pump operates.
NOTICE:

These tests must be done quickly (within 10 seconds)
to prevent the coil burning out.

Keep the fuel pump as far away from the battery as
possible.

Always do the switching at the battery side.

SF±8
± SFI (2JZ±GE)FUEL PUMP
1474 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
If operation is not as specified, replace the fuel pump.
(f) Reconnect the fuel pump & sender gauge connector.
(g) Reinstall the floor service hole cover with the cap nuts.
(h) Reinstall the rear seat cushion.

SF0ZQ±02
B07573
Vapor Pressure Sensor Connector
Vapor Pressure Sensor
Vacuum Hose
Charcoal Canister Assembly
SF±60
± SFI (2JZ±GE)VAPOR PRESSURE SENSOR
1526 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
VAPOR PRESSURE SENSOR
COMPONENTS

SF0O8±01
B07574
Voltmeter
Disconnect
E2VC
B07575
Disconnect
Pressure
Vacuum
PTNK
ECM
E2Voltmeter
± SFI (2JZ±GE)VAPOR PRESSURE SENSOR
SF±61
1527 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. INSPECT POWER SOURCE VOLTAGE OF VAPOR
PRESSURE SENSOR
(a) Disconnect the vapor pressure sensor connector.
(b) Turn the ignition switch ON.
(c) Using a voltmeter, measure the voltage between connec-
tor terminals VC and E2 of the wiring harness side.
Voltage: 4.5 ± 5.5 V
(d) Turn the ignition switch OFF.
(e) Reconnect the vapor pressure sensor connector.
2. INSPECT POWER OUTPUT OF VAPOR PRESSURE
SENSOR
(a) Turn the ignition switch ON.
(b) Disconnect the vacuum hose from the vapor pressure
sensor.
(c) Connect a voltmeter to terminals PTNK and E2 of the
ECM, and measure the output voltage under these condi-
tions:
(1) Apply vacuum (2.0 kPa (15 mmHg, 0.59 in.Hg)) to
the vapor pressure sensor.
Voltage: 1.3 ± 2.1 V
(2) Release the vacuum from the vapor pressure sen-
sor.
Voltage: 3.0 ± 3.6 V
(3) Apply pressure (1.5 kPa (15 gf/cm
2, 0.22 psi)) to the
vapor pressure sensor.
Voltage: 4.2 ± 4.8 V
(d) Turn the ignition switch OFF.
(e) Reconnect the vacuum hose to the vapor pressure sen-
sor.

SF0O9±04
B08975
N´m (kgf´cm, ft´lbf) : Specified torque

Non±reusable part
Knock Sensor 1
44 (450, 33)
Knock Sensor Connector
44 (450, 33)
Knock Sensor 2
Knock Sensor Connector
Engine Wire Clamp

O±Ring
Oil Dipstick and Guide for A/TPS Pump Rear Stay
Starter
Starter ConnectorClamp Bracket
Starter Wire
Engine Cover
SF±62
± SFI (2JZ±GE)KNOCK SENSOR
1528 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
KNOCK SENSOR
COMPONENTS

SF0OA±04
B09503
SST
P01630
OhmmeterNo Continuity
± SFI (2JZ±GE)KNOCK SENSOR
SF±63
1529 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. REMOVE ENGINE COVER
Remove the 4 nuts and engine cover.
2. REMOVE PS PUMP REAR STAY
3. REMOVE KNOCK SENSOR 1
(a) Disconnect the knock sensor connector.
(b) Using SST, remove the knock sensor.
SST 09816±30010
4. REMOVE OIL DIPSTICK AND GUIDE FOR A/T
(See page EM±62)
5. REMOVE STARTER (See page ST±4)
6. REMOVE KNOCK SENSOR 2 (See step 2)
7. INSPECT KNOCK SENSORS
Using an ohmmeter, check that there is no continuity between
the terminal and body.
If there is continuity, replace the sensor.
8. REINSTALL KNOCK SENSORS
(a) Using SST, install the knock sensor.
SST 09816±30010
Torque: 44 N´m (450 kgf´cm, 33 ft´lbf)
(b) Connect the knock sensor connector.
9. REINSTALL STARTER (See page ST±16)
10. REINSTALL OIL DIPSTICK AND GUIDE FOR A/T
HINT:
Use a new O±ring.
11. REINSTALL PS PUMP REAR STAY
Torque: 39.2 N´m (400 kgf´cm, 29 ft´lbf)
12. REINSTALL ENGINE COVER
Reinstall the engine cover with the 4 nuts.

SF0OB±03
B08325
Bank 1 Sensor 1
N´m (kgf´cm, ft´lbf): Specified torque
Heated Oxygen Sensor Connector
(On Water Pump)
Clamp
45 (450, 33)Heated Oxygen Sensor
B08326
Bank 1 Sensor 2
N´m (kgf´cm, ft´lbf) : Specified torque
Heated Oxygen Sensor Connector
Case Clamp
Front Suspension Member Brace
45 (450, 33)Heated Oxygen Sensor
SF±64
± SFI (2JZ±GE)HEATED OXYGEN SENSOR
1530 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
HEATED OXYGEN SENSOR
COMPONENTS

B08327
Bank 2 Sensor 1
N´m (kgf´cm, ft´lbf) : Specified torquePCV Hose
PS Air Hose
Air Cleaner Inlet
Wire Grommet EVAP Hose
Heated Oxygen Sensor
(Bank 2 Sensor 1)

Gasket Air Cleaner,
MAF Meter and
Intake Air Resonator
Assembly
MAF Meter Connector
Front Exhaust
Pipe

Gasket Engine Wire Clamp
Heated Oxygen Sensor
Connector
Case Clamp

Clamp
Pipe Support Bracket
Heated Oxygen Sensor Connector

Non±reusable part
44 (440, 32)
40 (408, 30)
44 (440, 32)
Exhaust Manifold
x 8
Engine Cover
± SFI (2JZ±GE)HEATED OXYGEN SENSOR
SF±65
1531 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)