2000 CHRYSLER CARAVAN key

TEST TC-16ACONTINUED - REPAIRING - TURBOCHARGER BOOST SENSOR SIGNAL LOW
EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-16A KEY OFF.
CONTINUED FROM DISCONNECT THE
THE PREVIOUS BOOST PRESSURE
PAGE. SENSOR HARNESS
CONNECTOR.**
USING A VOLTMETER, REPAIR THE 5-VOLT
MEASURE THE 5-VOLT IS THE VOLTAGE NO SUPPLY CIRCUIT FOR
TURN IGNITION ON. SUPPLY CIRCUIT. ABOVE 4.9 VOLTS? AN OPEN OR SHORT
TO GROUND.*
FIG.1
YES
CONNECT A JUMPER READ THE BOOST IS THE BOOST
BETWEEN THE BOOST PRESSURE SENSOR PRESSURE SENSOR YES REPLACE THE BOOST
PRESSURE SENSOR VOLTAGE ON THE VOLTAGE ABOVE 4.5 PRESSURE SENSOR.*
SIGNAL CKT. AND THE DRB. VOLTS?
5-VOLT CKT. FIG.1
NO
TURN IGNITION OFF. USING AN OHMMETER, REPAIR THE BOOST
DISCONNECT THE ECM MEASURE THE BOOST IS THE RESISTANCE YES PRESSURE SENSOR
HARNESS PRESSURE SENSOR BELOW 5.0 OHMS? SIGNAL CIRCUIT FOR
CONNECTORS.** SIGNAL CKT TO GND. A SHORT TO
FIG.1 GROUND.*
NO
USE AN OHMMETER IN SENSOR SIGNAL REPAIR THE SENSOR
THE FOLLOWING STEP. CIRCUIT AND THE IS THE RESISTANCE YES SIGNAL CIRCUIT
TEST THE RESISTANCE SENSOR GROUND BELOW 5.0 OHMS? SHORTED TO THE
BETWEEN THE BOOST CIRCUIT. SENSOR GROUND
PRESSURE... FIG.1 CIRCUIT.*
NO
USING AN OHMMETER,
MEASURE THE BOOST IS THE RESISTANCE YES REPLACE THE ENGINE
PRESSURE SENSOR BELOW 5.0 OHMS? CONTROL MODULE.*
SIGNAL CIRCUIT.
FIG.2
NO
REPAIR THE OPEN
BOOST PRESSURE
SENSOR SIGNAL
CIRCUIT.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
73
ProCarManuals.com

TEST TC-19ACONTINUED - REPAIRING - TURBOCHARGER BOOST SENSOR PLAUSIBILITY
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-19
CONTINUED FROM
THE PREVIOUS TURN IGNITION OFF.
PAGE.
DISCONNECT THE
DISCONNECT THE ECM BOOST PRESSURE
HARNESS SENSOR HARNESS
CONNECTORS.** CONNECTOR.**
MEASURE THE BOOST REPAIR THE BOOST
USE AN OHMMETER IN PRESSURE SENSOR IS THE RESISTANCE NO PRESSURE SENSOR
THE FOLLOWING SIGNAL CIRCUIT. BELOW 5.0 OHMS? SIGNAL CIRCUIT FOR
STEPS. HIGH RESISTANCE .*
FIG.1
YES
MEASURE THE BOOST REPAIR THE BOOST
PRESSURE SENSOR IS THE RESISTANCE NO PRESSURE SENSOR
GROUND CIRCUIT. BELOW 5.0 OHMS? GROUND CIRCUIT FOR
HIGH RESISTANCE.*
FIG.1
YES
MEASURE THE BOOST REPAIR THE BOOST
PRESSURE SENSOR IS THE RESISTANCE NO PRESSURE SENSOR
5-VOLT SUPPLY BELOW 5.0 OHMS? 5-VOLT SUPPLY
CIRCUIT. CIRCUIT FOR HIGH
FIG.1 RESISTANCE.*
YES
REPLACE THE BOOST TEST DRIVE THE
PRESSURE SENSOR.* VEHICLE AND PERFORM DOES THE DRB YES REPLACE THE ENGINE
TURN IGNITION ON SEVERAL KEY CYCLES. DISPLAY THIS CODE? CONTROL MODULE.*
AND CLEAR CODES. USING THE DRB, READ
CODES.
NO
TEST COMPLETE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
85
ProCarManuals.com

TEST TC-20ACONTINUED - REPAIRING - BRAKE SWITCH PLAUSIBILITY WITH REDUNDANT
CONTACT
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-20A KEY OFF.
CONTINUED FROM DISCONNECT THE
THE PREVIOUS BRAKE LAMP SWITCH
PAGE. HARNESS
CONNECTOR.**
USING A VOLTMETER,
PROBE BRAKE SWITCH IS THE VOLTAGE NO REPAIR OPEN FUSED
HARNESS CONNECTOR ABOVE 9.0 VOLTS? BATTERY SUPPLY
CAVITY 6. CIRCUIT.*
FIG.1
YES
CONNECT A JUMPER
WIRE ACROSS THE DID THE DRB CHANGE YES ADJUST OR REPLACE
BRAKE LAMP FROM "RELEASED" TO THE BRAKE LAMP
HARNESS CONNECTOR "PRESSED"? SWITCH.*
CAV 5 AND 6. FIG.1
NO
KEY ON. USING A AT THE BRAKE LAMP REPAIR THE PRIMARY
VOLTMETER, MEASURE SWITCH HARNESS IS THE VOLTAGE YES BRAKE LAMP SWITCH
THE PRIMARY SWITCH CONNECTOR CAVITY 5. ABOVE 1.0 VOLT? SIGNAL CIRCUIT FOR
SIGNAL VOLTAGE... A SHORT TO
FIG.1 VOLTAGE.*
NO
KEY OFF. USING AN OHMMETER, REPAIR THE OPEN
DISCONNECT THE ECM MEASURE RESISTANCE IS THE RESISTANCE NO PRIMARY BRAKE LAMP
HARNESS OF THE PRIMARY BRAKE BELOW 5.0 OHMS? SWITCH SIGNAL
CONNECTORS.** LAMP SWITCH SIGNAL CIRCUIT.*
CIRCUIT. FIG.2
YES
REPLACE THE ENGINE
CONTROL MODULE.* SW
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
89
ProCarManuals.com

TEST TC-20BREPAIRING - BRAKE SWITCH PLAUSIBILITY WITH REDUNDANT CONTACT
Perform TEST TC-20A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST
TC-20B. TURN IGNITION OFF.
DISCONNECT THE KEY ON. USING A
BRAKE LAMP SWITCH VOLTMETER, MEASURE IS THE VOLTAGE NO CONTINUE TEST
HARNESS HARNESS CONNECTOR ABOVE 9.0 VOLTS? TC-20B ON THE
CONNECTOR.** CAVITY 1. NEXT PAGE.
FIG.1
YES
CONNECT A FUSEDREPAIR THE
JUMPER WIRE (5 AMP),YES SECONDARY BRAKE SW
ACROSS BRAKE LAMP CHECK THE FUSE. DID FUSE OPEN? SENSE CIRCUIT FOR
SWITCH HARNESS CONN A SHORT TO
CAVITIES 1 AND 2. VOLTAGE.*
NO
DID THE DRB
DISPLAY CHANGE YES ADJUST OR REPLACE
FROM "PRESSED" TO THE BRAKE LAMP
"RELEASED"? SWITCH.*
NO
KEY OFF. BRAKE LAMP SWITCH REPAIR THE OPEN
USING AN OHMMETER, HARNESS CONNECTOR IS THE RESISTANCE NO SECONDARY BRAKE
MEASURE THE CAVITY 2 AND GROUND. BELOW 5.0 OHMS? LAMP SWITCH GROUND
RESISTANCE CIRCUIT.*
BETWEEN... FIG.1
YES
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
91
ProCarManuals.com

TEST TC-20BCONTINUED - REPAIRING - BRAKE SWITCH PLAUSIBILITY WITH REDUNDANT
CONTACT
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-20B KEY OFF.
CONTINUED FROM DISCONNECT THE ECM
THE PREVIOUS HARNESS
PAGE. CONNECTORS.**
OF THE SECONDARY REPAIR OPEN IN THE
USING AN OHMMETER, BRAKE LAMP SWITCH IS THE RESISTANCE NO SECONDARY BRAKE
MEASURE THE SIGNAL CIRCUIT. BELOW 5.0 OHMS? LAMP SWITCH SIGNAL
RESISTANCE...CIRCUIT.*
FIG.1
YES
USING AN OHMMETER, THE BRAKE LAMP REPAIR SHORT TO
MEASURE THE SWITCH HARNESS IS THE RESISTANCE YES GROUND IN THE
RESISTANCE CONNECTOR CAVITY 1 BELOW 5.0 OHMS? SECONDARY BRAKE
BETWEEN... AND GROUND. LAMP SWITCH SIGNAL
FIG.2 CIRCUIT.*
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
93
ProCarManuals.com

TEST TC-25AREPAIRING - CRUISE STATUS INDICATOR LAMP SHORT CIRCUIT
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TURN IGNITION ON.
START TEST USING THE DRB,
TC-25A. CLEAR TROUBLE
CODES.
TURN IGNITION ON.
TURN IGNITION OFF. PRESS THE SPEED DID TROUBLE CODE YES CONTINUE TEST
WAIT 30 SECONDS. CONTROL ON/OFF RESET? TC-25A ON NEXT
BUTTON SEVERAL PAGE.
TIMES.
NO
THE CONDITION TO SET USING THE SCHEMATIC
THE TROUBLE CODE IS AS A GUIDE, INSPECT WERE ANY PROBLEMS YES REPAIR AS
NOT PRESENT. THE WIRING AND FOUND? NECESSARY.*
CONNECTORS.
FIG.1 FIG.2
NO
KEY ON. WIGGLE THEREPAIR AS
WIRING FROM THE BODY CONTROL DOES DRB DISPLAY YES NECESSARY WHERE
ENGINE CONTROL MODULE. TROUBLE CODE? WIGGLING CAUSED
MODULE TO THE ...FAULT.*
NO
REFER TO GENERAL
INFORMATION 3.3.2
FOR ADDITIONAL TEST COMPLETED.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
107
ProCarManuals.com

TEST TC-25ACONTINUED - REPAIRING - CRUISE STATUS INDICATOR LAMP SHORT CIRCUIT
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
KEY ON. USING A
VOLTMETER, MEASURE
ECM HARNESS CONNEC-
TOR CAVITY 30.
FIG. 2
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
109
ProCarManuals.com

TEST TC-26ACONTINUED - REPAIRING - DIAGNOSTIC LAMP OPEN CIRCUIT
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-26A
CONTINUED FROM
THE PREVIOUS TURN IGNITION OFF.
PAGE.
DISCONNECT THE ECM USING AN OHMMETER, REPAIR OPEN
AND MESSAGE CENTER MEASURE RESISTANCE IS THE RESISTANCE YES DIAG/GLOW PLUG
HARNESS OF THE DIAG/GLOW ABOVE 5.0 OHMS? LAMP CONTROL
CONNECTORS.** PLUG LAMP CONTROL CIRCUIT.*
CIRCUIT. FIG.1
NO
USING AN OHMMETER,REPAIR THE
MEASURE ECM HARNESS IS THE RESISTANCE YES DIAG/GLOW PLUG
CONNECTOR CAVITY 24 BELOW 5.0 OHMS? LAMP CONTROL
TO GROUND.CIRCUIT FOR A
FIG.2SHORT TO GROUND.
NO
KEY ON. CONNECT A
RECONNECT THE JUMPER WIRE BETWEEN DID THE DIAG/GLOW YES REPLACE THE ENGINE
MESSAGE CENTER ECM HARNESS PLUG LAMP CONTROL MODULE.*
HARNESS CONNECTOR. CONNECTOR CAVITY 34 ILLUMINATE.
AND GROUND. FIG.2
NO
INSPECT DIAG/GLOWNO REPLACE THE BULB
PLUG LAMP BULB. IS THE BULB OK? AND RETEST.*
YES
REPLACE THE
MESSAGE CENTER.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
11 3
ProCarManuals.com