2000 CHRYSLER CARAVAN key

TEST VER-1ANO START VERIFICATION
Important Note:
If the Engine Control Module, Sentry Key Immobilizer Module or Body Control Module have been
changed the Vehicle Identification Number (VIN) and Secret Key data must be updated to enable the
vehicle to start and run. Refer to GENERAL INFORMATION SECITON 8.0 for programming
procedures.
Inspect the vehicle to ensure that all engine components are connected. Reassemble and reconnect
components as necessary.
Inspect the engine oil for contamination. If it is contaminated, change the oil and filter.
Using the DRB, clear all diagnostic trouble codes (DTC's).
Turn the ignition off for 10 seconds.
Attempt to start the vehicle.
If the engine isunableto start, look for any Technical Service Bulletins that may relate to this
condition. Return toDTC TESTif necessary.
The repair is now complete.
V
E
R
I
F
I
C
A
T
I
O
N
T
E
S
T
422
ProCarManuals.com

8.0 MAINTENANCE AND SERVICE INFORMATION
Refer to the appropriate service manual for information about repair and replacement procedures
When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
The use of a fuse with a rating other than indicated may result in a dangerous electrical system
overload. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must
be corrected.
NOTE:If it is necessary to replace the body controller and the SKIM, perform the following steps
in order:
± program the new body controller
± program the new SKIM
± replace all ignition keys, program new ignition keys to new SKIM
NOTE:If it is necessary to replace the engine control module and the SKIM, perform the following
steps in order:
± program the new SKIM
± program the new engine control module
8.1 Programming the Engine Control Module
1. To program the VIN, connect the DRB and turn ignition on.
2. Select ªENGINEº from the main menu. The DRB will request the SKIS four-digit PIN.
3. Enter the PIN.
4. Select ªENTERº to update the VIN. The DRB will display the updated VIN.
5. If the engine is equipped with air conditioning, the ECM a/c function must be enabled.
± Using the DRB select ªENGINEº, ªMISCELLANEOUSº then ªENABLE/DISABLE A/Cº.
± Push 1 to enable A/C. DRB screen should display ªA/C Activatedº.
8.2 Programming the Body Control Module
The SKIS ªSecret Keyº is an I.D. code that is unique to each SKIM. This code is programmed and
stored in the SKIM, body controller and transponder chip (ignition keys). When replacing the BCM
it is necessary to program the secret key into the new BCM using the DRB. Perform the following
steps to program the secret key into the body controller.
1. Turn the ignition on (transmission in park/neutral).
2. Use the DRB and select ``THEFT ALARM'', ``SKIM'' then ``MISCELLANEOUS''.
3. Select ``GS DIESEL BCM REPLACED''.
4. SELECT ªENTERº to update BCM VIN.
5. Enter secured access mode by entering the vehicle four-digit PIN.
NOTE:If three attempts are made to enter secure access mode using an incorrect PIN, secured
access mode will be locked out for one hour. To exit this lockout mode, turn the ignition to the RUN
position for one hour then enter the correct PIN. (Ensure all accessories are turned off. Also
monitor the battery state and connect a battery charger if necessary).
6. Press ªENTERº to transfer the secret key (the SKIM will send the secret key to the BCM).
G
E
N
E
R
A
L
I
N
F
O
R
M
A
T
I
O
N
425
ProCarManuals.com

8.3 Programming the Sentry Key Immobilizer Module
1. Turn the ignition on (transmission in park/neutral).
2. Use the DRB and select ``THEFT ALARM'', ``SKIM'' then ``MISCELLANEOUS''.
3. Select ``SKIM REPLACED (DIESEL)''.
4. Program the vehicle four-digit PIN into SKIM.
5. Select ªCOUNTRY CODEº and enter the correct country.
NOTE:Be sure to enter the correct country code. If the incorrect country code is programmed into
SKIM, the SKIM must be replaced.
6. Select ªUPDATE VINº (the skim will learn the VIN from the BCM).
7. Press ªENTERº to transfer the secret key (the BCM will send the secret key to the SKIM).
8. Program ignition keys to SKIM (for programming procedure, refer toGENERAL INFORMA-
TION SECTION 8.3).
NOTE:If the BCM and the SKIM are replaced at the same time, all vehicle keys will need to be
replaced and programmed to the new SKIM.
8.4 Programming Ignition Keys to the Sentry Key Immobilizer Module
1. Turn the ignition on (transmission in park/neutral).
2. Use the DRB and select ªTHEFT ALARMº, ªSKIMº then ªMISCELLANEOUSº.
3. Select ªPROGRAM IGNITION KEY'Sº.
4. Enter secured access mode by entering the vehicle four-digit PIN.
NOTE:A maximum of eight keys can be learned to each SKIM. Once a key is learned to a SKIM
it (the key) cannot be transferred to another vehicle.
If ignition key programming is unsuccessful, the DRB will display one of the following messages:
Programming Not Attempted - The DRB attempts to read the programmed key status and there
are no keys programmed into SKIM memory.
Programming Key Failed (Possible Used Key From Wrong Vehicle) - SKIM is unable to program
key due to one of the following:
± faulty ignition key transponder
± ignition key is programmed to another vehicle.
8 Keys Already Learned, Programming Not Done - SKIM transponder ID memory is full.
1. Obtain ignition keys to be programmed from cluster (8 keys maximum)
2. Using the DRB, erase all ignition keys by selecting ªMISCELLANEOUSº and ªERASE ALL
CURRENT IGN. KEYSº
3. Program all ignition keys.
Learned Key In Ignition - Ignition key transponder ID is currently programmed in SKIM memory.
G
E
N
E
R
A
L
I
N
F
O
R
M
A
T
I
O
N
426
ProCarManuals.com

rough,
un-stable or
erratic idle
stallingThe engine runs unevenly at idle and causes the engine to shake if it is
severe enough. The engine idle rpm may vary (called ``hunting''). This
condition may cause stalling if it is severe enough.
SKIMSentry key immobilizer module
SKISSentry key immobilizer system
start and
stallThe engine starts but immediately dies.
surgeengine rpm fluctuation without corresponding change in throttle position
sensor
SRCsignal range check
VSSvehicle speed sensorG
E
N
E
R
A
L
I
N
F
O
R
M
A
T
I
O
N
429
ProCarManuals.com