2000 CHRYSLER CARAVAN key

TEST SC-6ACHECKING CRUISE INDICATOR OPERATION
Perform TEST SC-1A Before Proceeding
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
NOTE: PERFORM TEST
START TEST SC-1A TO VERIFY
SC-6A. PROPER CRUISE
SWITCH OPERATION
BEFORE CONTINUING.
TURN IGNITION ON. MONITOR CRUISE DOES LAMP STATE CHECK CRUISE LAMP
WITH THE DRB SELECT LAMP STATE WHILE CHANGE FROM "ON" YES BULB, REPLACE AS
"BODY" "MIC" PRESSING CRUISE TO "OFF" WHEN NECESSARY. IF OK,
"MONITOR DISPLAY" ON/OFF BUTTON PRESSING THE REPLACE THE
THEN "CCD BUS INFO". SEVERAL TIMES. BUTTON? INSTRUMENT CLUSTER.*
NO
KEY OFF. KEY ON. CONNECT A
DISCONNECT THE ECM JUMPER WIRE BETWEEN IS THE SPEED YES REPLACE THE ENGINE
HARNESS ECM HARNESS CONTROL LAMP ON? CONTROL MODULE.*
CONNECTORS.** CONNECTOR CAVITY 30
AND GROUND. FIG.1
NO
KEY OFF. USING AN OHMMETER, REPAIR SHORT TO
DISCONNECT THE BCM MEASURE RESISTANCE IS THE RESISTANCE YES GROUND ON THE
HARNESS BETWEEN ECM HARNESS BELOW 5.0 OHMS? SPEED CONTROL LAMP
CONNECTORS.** CONNECTOR CAVITY 30 CONTROL CIRCUIT.*
AND GROUND. FIG.1
NO
USING AN OHMMETER
MEASURE THE SPEED IS THE RESISTANCE YES REPAIR OPEN SPEED
CONTROL LAMP ABOVE 5.0 OHMS? CONTROL LAMP
CONTROL CIRCUIT. CONTROL CIRCUIT.*
FIG.2
NO
REPLACE THE BODY
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
391
ProCarManuals.com

TEST NS-SELNO START SELECTION MENU
NOTE:The battery must be fully charged before performing any test in this manual.
NOTE:If the engine will not crank or cranks but will not run, be sure to check the Sentry Key
Immobilizer Module (SKIM) for proper communication and trouble codes.
NOTE:With the DRB, attempt to read ECM trouble codes. If the DRB is unable to communicate with
the ECM, perform test NS-2A. If there are any trouble codes present they must be repaired before
continuing with the No Start Symptom diagnostics.
Below you will find a recommended procedure to correct a No Start Problem by symptom. They
should be performed in the order that they are listed.
Repairing a No Crank Condition..............................................NS-1A
Repairing a No Response Condition...........................................NS-2A
Repairing a No Start Condition................................................NS-3A
Repairing a Start and Stall Condition...........................................NS-4A
Checking the Engine Mechanical Systems......................................NS-5A
NOTE:A failed engine coolant temperature (ECT) sensor can cause a cranks but will not run or an
extended cranking before starting condition. This occurs when the ECT sensor calibration fails
(sensor indicates engine temp is warmer than actual engine temp) and the ECM cannot command
proper fuel quantity to the injection pump.
NOTE:For all component locations seeGeneral Information Section 4.0 in this manual.
N
O
S
T
A
R
T
T
E
S
T
S
392
ProCarManuals.com

TEST NS-1AREPAIRING A NO CRANK CONDITION
Perform TEST NS-SEL Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
NOTE: BATTERY MUST
START TEST BE FULLY CHARGED
NS-1A. BEFORE DIAGNOSING
A NO-START
CONDITION.
NOTE: BEFORE VEHICLE THEFT DIAGNOSE
CONTINUING, BE (SKIM) SYSTEM FOR ARE ANY CODES YES TROUBLE CODE
SURE TO CHECK DIAGNOSTIC TROUBLE PRESENT? BEFORE
ENGINE SYSTEM CODES. CONTINUING.]
AND...
NO
INSPECT BATTERY
CABLES FOR IS THERE EVIDENCE YES REPAIR AS
TURN IGNITION OFF. CORROSION, OF PROBLEMS? NECESSARY.*
LOOSENESS OR OTHER
PROBLEMS.
NO
TURN IGNITION OFF. KEY ON. WITH A REPAIR THE STARTER
VOLTMETER, MEASURE IS THE VOLTAGE YES RELAY CONTROL
DISCONNECT THE ECM THE STARTER RELAY ABOVE 1.0 VOLT? CIRCUIT FOR A
HARNESS CONTROL CKT. SHORT TO VOLTAGE.*
CONNECTORS.** FIG.1
NO
KEY OFF. USING A FULLY DEPRESS THE
JUMPER WIRE CONNECT CLUTCH PEDAL. DID THE ENGINE YES REPLACE THE ENGINE
THE STARTER RELAY CRANK? CONTROL MODULE.*
CONTROL CKT TO ATTEMPT TO CRANK
GROUND. FIG.1 THE ENGINE.
NO
WITH A VOLTMETER,
DISCONNECT THE MEASURE THE FUSED IS THE VOLTAGE NO REPAIR OPEN FUSED
STARTER RELAY FROM B(+) CIRCUIT. ABOVE 11.6 VOLTS? BATTERY CIRCUIT.*
THE PDC.**
FIG.1
YES
WARNING: THE TRANS WARNING: THE ENGINE BRIEFLY CONNECT A
MUST BE IN NEUTRAL MAY BE CRANKED IN JUMPER WIRE BETWEEN CONTINUE TEST
AND THE PARKING THE NEXT STEP. KEEP THE STARTER RLY NS-1A ON THE
BRAKE MUST BE ON AWAY FROM MOVING OUTPUT AND FUSED NEXT PAGE.
FOR THE NEXT STEP. ENGINE PARTS. B(+) CKTS. FIG.1
N
O
S
T
A
R
T
T
E
S
T
S
395
ProCarManuals.com

TEST NS-1ACONTINUED - REPAIRING A NO CRANK CONDITION
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
TEST NS-1A KEY OFF. WITH AN IS THE RESISTANCE
CONTINUED FROM OHMMETER, MEASURE BETWEEN NO REPLACE THE
THE PREVIOUS THE STARTER RELAY 60.0 AND 90.0 STARTER RELAY.*
PAGE. TERMINALS 85 AND 86. OHMS?
FIG.1
YES
KEY ON. USING A AT THE ECM HARNESS REPAIR THE STARTER
VOLTMETER, MEASURE CONNECTOR. IS THE VOLTAGE YES RELAY CONTROL CKT
STARTER RELAY ABOVE 1.0 VOLT? FOR A SHORT TO
CONTROL CKT... VOLTAGE.*
FIG.2
NO
WITH AN OHMMETER, BETWEEN THE ECM
MEASURE RESISTANCE HARNESS CONNECTOR IS THE RESISTANCE YES REPAIR THE OPEN
OF THE STARTER AND THE PDC ABOVE 5.0 OHMS? STARTER RELAY
RELAY CONTROLCONTROL CIRCUIT.*
CIRCUIT... FIG.2
NO
KEY ON. USING A WITH THE CLUTCH
VOLTMETER, MEASURE WHILE DEPRESSING DEPRESSED, IS THE YES REPLACE THE
THE CLUTCH THE CLUTCH. VOLTAGE ABOVE 10.0 STARTER RELAY.*
INTERLOCK SWITCH VOLTS?
CKT AT THE PDC)...
NO
KEY OFF. DISCONNECT MEASURE CLUTCH
THE CLUTCH INTERLOCK INTERLOCK SWITCH IS THE VOLTAGE NO REPAIR OPEN CLUTCH
SWITCH HARNESS HARNESS CONNECTOR ABOVE 10.0 VOLTS? INTERLOCK SWITCH
CONNECTOR. KEY ON. CAVITY 1. BATTERY SUPPLY.*
USING A VOLTMETER... FIG.3
YES
CONNECT A JUMPER PROBE THE CLUTCH
WIRE ACROSS THE INTERLOCK SWITCH IS THE VOLTAGE YES ADJUST OR REPLACE
CLUTCH INTERLOCK OUTPUT CKT. IN THE ABOVE 10.0 VOLTS? THE CLUTCH
SWITCH HARNESS PDC. INTERLOCK SWITCH.*
CONNECTOR. FIG.2
NO
REPAIR OPEN
CIRCUIT BETWEEN
STARTER RELAY AND
CLUTCH INTERLOCK
SWITCH.*
N
O
S
T
A
R
T
T
E
S
T
S
399
ProCarManuals.com

TEST NS-2AREPAIRING A NO RESPONSE CONDITION
Perform TEST NS-SEL Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
START TEST DOES THE VEHICLE YES PERFORM TEST
NS-2A. START? NS-2B.
NO
KEY OFF. WITH AN OHMMETER, IS THE RESISTANCE
MEASURE RESISTANCE ABOVE 5.0 OHMS FOR YES REPAIR THE OPEN
DISCONNECT THE ECM OF THE PCM GND CKTS ANY OF THE ECM GROUND.*
HARNESS AT HARNESS CAVITIES MEASUREMENTS?
CONNECTORS.** 1 AND 27. FIG.1
NO
KEY ON. USING A AT ECM HARNESS REPAIR OPEN OR
VOLTMETER, MEASURE CONNECTOR CAVITY 47. IS THE VOLTAGE NO SHORT TO GROUND IN
THE FUSED IGNITION ABOVE 10.0 VOLTS? THE FUSED IGNITION
SWITCH OUTPUT SWITCH OUTPUT
CIRCUIT... FIG.1 CIRCUIT.*
YES
KEY OFF. USING A VOLTMETER REPAIR OPEN FUSE
REMOVE THE DIESEL PROBE DIESEL POWER IS THE VOLTAGE NO OR FUSED BATTERY
POWER RELAY. RELAY CONNECTOR ABOVE 10.0 VOLTS? CIRCUIT TO DIESEL
CAVITY 30 (IN PDC). POWER RELAY.*
KEY ON. FIG.2
YES
KEY OFF. CONNECT A MEASURE VOLTAGE AT IS THE VOLTAGE
JUMPER WIRE ACROSS ECM HARNESS ABOVE 10.0 VOLTS NO REPAIR OPEN DIESEL
RELAY CONNECTOR CONNECTOR CAVITIES FOR EACH POWER RELAY OUTPUT
CAVATIES 30 AND 87. 2 AND 28. MEASUREMENT? CIRCUIT(S).*
FIG. 1 AND 2
YES
KEY OFF. RECONNECT WITH JUMPER WIRE
THE ENGINE CONTROL STILL CONNECTED, DOES THE VEHICLE NO REPLACE THE ENGINE
MODULE HARNESS ATTEMPT TO START START? CONTROL MODULE.*
CONNECTORS. VEHICLE.
YES
CONTINUE TEST
NS-2A ON THE
NEXT PAGE.
N
O
R
E
S
P
O
N
S
E
T
E
S
T
401
ProCarManuals.com

TEST NS-2BREPAIRING A NO RESPONSE CONDITION
Perform TEST NS-2A Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
WAS THE IGNITION TURN IGNITION ON
START TEST ON WHEN THE "NO NO TO GET A RESPONSE.
NS-2B. RESPONSE" MESSAGE
WAS DISPLAYED? TEST COMPLETE.
YES
KEY ON. PROBE THE
ISO K-LINE CIRCUIT IS THE TEST LIGHT YES REPAIR THE ISO
USE A TEST LIGHT AT THE DLC. ON? K-LINE FOR A SHORT
IN THE FOLLOWINGTO VOLTAGE.*
STEP. FIG.1
NO
KEY OFF.
DISCONNECT DRB
DISCONNECT THE ECM FROM THE DATA LINK
HARNESS CONNECTOR.
CONNECTORS.**
MEASURE THE
USE AN OHMMETER IN RESISTANCE OF THE IS THE RESISTANCE YES REPAIR THE ISO
THE FOLLOWING ISO K-LINE AT THE BELOW 5.0 OHMS? K-LINE CIRCUIT FOR
STEPS. DLC CONNECTOR TO A SHORT TO GROUND.
GROUND FIG.1
NO
MEASURE THE
RESISTANCE OF THE IS THE RESISTANCE NO REPAIR THE OPEN
ISO K-LINE AT THE BELOW 5.0 OHMS? ISO K-LINE
DLC CONN. TO THE CIRCUIT.
ECM CONN. FIG.2
YES
MEASURE BETWEEN THE DLC CAVITIES REPAIR THE GROUND
CHASSIS GROUND AND 4 AND 5. IS THE RESISTANCE NO CIRCUIT(S) THAT
THE GROUND BELOW 5.0 OHMS FOR MEASURED ABOVE 5.0
CIRCUITS AT... EACH MEASUREMENT? OHMS FOR AN OPEN.*
FIG.1
YES
CONTINUE TEST
NS-2B ON THE
NEXT PAGE.
N
O
R
E
S
P
O
N
S
E
T
E
S
T
407
ProCarManuals.com

TEST NS-3BCONTINUED - REPAIRING - NO START
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
TEST NS-3B TURN IGNITION OFF.
CONTINUED FROM RECONNECT THE
THE PREVIOUS ENGINE CONTROL
PAGE. MODULE HARNESS
CONNECTORS.
KEY ON. MEASURE
USE AN AMMETER IN AMPERAGE FROM BCM IS THE AMPERAGE NO REPLACE THE ENGINE
THE FOLLOWING HARNESS CONNECTOR BETWEEN 1.0 AND CONTROL MODULE.*
STEP. CAVITY 72 TO GROUND. 1.4 MA?
FIG.1
YES
RECONNECT THE BODY USING THE DRB
CONTROL MODULE OSCILLOSCOPE
HARNESS FUNCTION, SELECT
CONNECTORS. "LAB SCOPE".
SET VOLTAGE RANGE TO KEY ON. USING
+20.0V. SET TIME OSCILLOSCOPE LEAD,
RANGE TO 0.1S/DIV. BACKPROBE ECM
SET PROBE TO X10. HARNESS CONNECTOR
FIG.2 CAVITY 38. FIG.1
NOTE: AN IMMOBILIZER DOES THE DRB DISPLAY
SIGNAL WILL CYCLE HI SHOW THE 12 VOLT YES REPLACE THE ENGINE
TO LO SIMILAR TO THE IMMOBILIZER SIGNAL CONTROL MODULE.*
PATTERN SHOWN IN CYCLING HI AND LO?
FIG.2 FIG.2
NO
REPLACE THE BODY
CONTROL MODULE.*
N
O
S
T
A
R
T
T
E
S
T
S
417
ProCarManuals.com

TEST NS-5ACHECKING THE ENGINE MECHANICAL SYSTEMS
Perform TEST NS-SEL Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
KEY OFF. USING
START TEST SERVICE MANUAL IS THE VALVE NO REPAIR VALVE
NS-5A. PROCEDURES, CHECK TIMING WITHIN TIMING AS
ENGINE VALVE SPECIFICATIONS? NECESSARY.
TIMING.
YES
USING SERVICE
MANUAL PROCEDURES, IS ENGINE NO REPAIR THE ENGINE
CHECK ENGINE COMPRESSION WITHIN AS NECESSARY.
COMPRESSION. SPECIFICATIONS?
YES
USING SERVICE
MANUAL IS INJECTION PUMP NO REPAIR INJECTION
PROCEEDURES, CHECK TIMING WITHIN PUMP TIMING AS
INJECTION PUMP SPECIFICATIONS? NECESSARY.
TIMING.
YES
TEST COMPLETED.
N
O
S
T
A
R
T
T
E
S
T
S
421
ProCarManuals.com