1999 TOYOTA CAMRY coolant

DI07B±07
± DIAGNOSTICSENGINE (1MZ±FE)
DI±211
446 Author: Date:
DIAGNOSTIC TROUBLE CODE CHART
1. SAE CONTROLLED
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, check the circuit for that code listed
in the table below. For details of each code, turn to the page referred to under the ''See page '' for the respec-
tive ''DTC No.'' in the DTC chart.
DTC No.
(See Page)Detection ItemTrouble AreaMIL*1Memory
P0100
(DI±222)Mass Air Flow Circuit
MalfunctionOpen or short in mass air flow meter circuit
Mass air flow meter
ECM

P0101
(DI±227)Mass Air Flow Circuit
Range/Performance
Problem
Mass air flow meter
P0110
(DI±228)Intake Air Temp. Circuit
MalfunctionOpen or short in intake air temp. sensor circuit
Intake air temp. sensor (built into mass air flow meter)
ECM

P0115
(DI±233)Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
Engine coolant temp. sensor
ECM

P0116
(DI±237)Engine Coolant Temp. Circuit
Range/Performance ProblemEngine coolant temp. sensor
Cooling system
P0120
(DI±239)Throttle/Pedal Position
Sensor/Switch ºAº Circuit
MalfunctionOpen or short in throttle position sensor circuit
Throttle position sensor
ECM

P0121
(DI±243)Throttle/Pedal Position
Sensor/Switch ºAº Circuit
Range/Performance Problem
Throttle position sensor
*2
P0125
(DI±244)
Insufficient Coolant Temp. for
Closed Loop Fuel Control
(Except California Spec.)
Fuel system
Injector
Ignition system
Gas leakage on exhaust system
Open or short in heated oxygen sensor circuit
(bank 1, 2 sensor 1)
Heated oxygen sensor (bank 1, 2 sensor 1)
ECM

*3
P0125
(DI±249)
Insufficient Coolant Temp. for
Closed Loop Fuel Control
(Only for California Spec.)
Fuel system
Injector
Ignition system
Gas leakage on exhaust system
Open or short in A/F sensor circuit (bank 1, 2 sensor 1)
A/F sensor (bank 1, 2 sensor 1)
ECM

*2
P0130
(DI±255)Heated Oxygen Sensor Circuit
Malfunction (Bank 1 Sensor 1)Heated oxygen sensor
Fuel trim malfunction
*1: 


MIL lights up
*
2: Except California specification vehicles
*
3: Only for California specification vehicle

DI±212
± DIAGNOSTICSENGINE (1MZ±FE)
447 Author: Date:
DTC No.
(See Page)Detection ItemTrouble AreaMILMemory
*2
P0133
(DI±259)
Heated Oxygen Sensor Circuit
Slow Response
(Bank 1 Sensor 1)Heated oxygen sensor
Fuel trim malfunction
*2
P0135
(DI±263)
Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 1)Open or short in heater circuit of heated oxygen sensor
Heated oxygen sensor heater
ECM

P0136
(DI±265)Heated Oxygen Sensor Circuit
Malfunction
(Bank 1 Sensor 2)
Heated oxygen sensor
P0141
(DI±263)Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 2)
Same as DTC No. P0135*1
*3
P0150
(DI±255)
Heated Oxygen Sensor
Circuit Malfunction
(Bank 2 Sensor 1)
Same as DTC No. P0130*1
*3
P0153
(DI±259)
Heated Oxygen Sensor
Circuit Slow Response
(Bank 2 Sensor 1)Same as DTC No. P0133
Fuel trim malfunction*1
*3
P0155
(DI±263)Heated Oxygen Sensor
Circuit Malfunction
(Bank 2 Sensor 1)
Same as DTC No. P0135*1
*3
P0171
(DI±272)System too Lean
(Fuel Trim)
(Except California Spec.)
Air intake (hose loose)
Fuel line pressure
Injector blockage
Heated oxygen sensor (bank 1, 2 sensor 1) malfunction
Mass air flow meter
Engine coolant temp. sensor
Gas leakage on exhaust system
*1
*3
P0172
(DI±272)System too Rich
(Fuel Trim)
(Except California Spec.)
Fuel line pressure
Injector leak, blockage
Heated oxygen sensor (bank 1, 2 sensor 1) malfunction
Mass air flow meter
Engine coolant temp. sensor
Gas leakage on exhaust system
*1
*4
P0171
(DI±267)System too Lean
(Fuel Trim)
(Only for California Spec.)
Air intake (hose loose)
Fuel line pressure
Injector blockage
Mass air flow meter
Engine coolant temp. sensor
A/F sensor (bank 1, 2 sensor 1)
Gas leakage on exhaust system
*1
*4
P0172
(DI±267)System too rich
(Fuel Trim)
(Only for California Spec.)
Fuel line pressure
Injector leak, blockage
Heated oxygen sensor malfunction
Mass air flow meter
Engine coolant temp. sensor
A/F sensor (bank 1, 2 sensor 1)
Gas leakage on exhaust system
*1
*1: MIL lights up
*2: MIL light up or blinking
*3: Except California specification vehicles
*4: Only for California specification vehicle

± DIAGNOSTICSENGINE (1MZ±FE)
DI±213
448 Author: Date:
DTC No.
(See Page)Detection ItemTrouble AreaMILMemory
P0300
(DI±276)Random/Multiple Cylinder
Misfire DetectedIgnition system
Injector
Fuel line pressure
EGR
P0301
P0302
P0303
P0304
P0305
P0306
(DI±276)Misfire Detected
± Cylinder 1
± Cylinder 2
± Cylinder 3
± Cylinder 4
± Cylinder 5
± Cylinder 6
EGR
Compression pressure
Valve clearance not to specification
Valve timing
Mass air flow meter
Engine coolant temp. sensor
Open or short engine wire
Connector connection
ECM
*2
P0325
(DI±283)Knock Sensor 1 Circuit
MalfunctionOpen or short in knock sensor 1 circuit
Knock sensor 1 (looseness)
ECM
*1
P0330
(DI±283)Knock Sensor 2 Circuit
MalfunctionOpen or short in knock sensor 2 circuit
Knock sensor 2 (looseness)
ECM
*1
P0335
(DI±287)Crankshaft Position Sensor
ºAº Circuit Malfunction
Open or short in crankshaft position sensor circuit
Crankshaft position sensor
Starter
ECM
*1
P0340
(DI±290)Camshaft Position Sensor
Circuit Malfunction
Open or short in camshaft position sensor circuit
Camshaft position sensor
Starter
ECM
*1
P0401
(DI±292)Exhaust Gas Recirculation
Flow Insufficient Detected
EGR valve (stuck closed)
Open or short in EGR gas temp. sensor circuit
EGR gas temp. sensor
Open in VSV circuit for EGR
VSV for EGR
Vacuum control valve
Vacuum hose disconnected or blocked
ECM
*1
P0402
(DI±302)Exhaust Gas Recirculation
Flow Excessive Detected
EGR valve stuck open
VSV for EGR open malfunction
Short in VSV circuit for EGR
Open or short in EGR valve position sensor circuit
EGR valve position sensor
ECM
*1
*3
P0420
(DI±305)Catalyst System Efficiency
Below Threshold
(Except California Spec.)Three±way catalytic converter
Open or short in heated oxygen sensor circuit
Heated oxygen sensor
*2
*4
P0420
(DI±308)Catalyst System Efficiency
Below Threshold
(Only for California Spec.)
Three±way catalytic converter
Open or short in heated oxygen sensor (bank 1, sensor 2)
circuit
Heated oxygen sensor (bank 1, sensor 2)
Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
A/F sensor (bank 1, 2 sensor 1)
*2
*1: MIL lights up
*2: MIL lights up on U.S.A and Canadian specification vehicles
*3: Except California specification vehicles
*4: Only for California specification vehicle

DI07C±06
A07469
Engine Coolant
Temp. Sensor
Heated Oxygen Sensor
(Bank 1 Sensor 2) VSV for EVAP VSV for ACIS
Crankshaft Position
Sensor
Camshaft Position
Sensor
Heated Oxygen Sensor *1
(Bank 1 Sensor 1)
A/F Sensor*2
(Bank 1 Sensor 1)Park/Neutral Position Switch
Knock Sensor 1 Knock Sensor 2
EGR Gas Temp. Sensor InjectorDLC1ECMVSV for EGR
IAC ValveMass Air Flow MeterIgniter
*1 : Except California Specification vehicles
*2 : Only for California Specification vehiclesVapor Pressure
Sensor
DLC3
Heated Oxygen Sensor *1
(Bank 2 Sensor 1)
A/F Sensor*2
(Bank 2 Sensor 1)
Canister
EGR Valve
Position Sensor
± DIAGNOSTICSENGINE (1MZ±FE)
DI±217
452 Author: Date:
PARTS LOCATION

DI4DP±01
A02508
E11E10
E9E8
313029
2827 17
18 19 20 21
2223 24
25 26 11 1 2 13 14 15
161 2
3 4
5 6 7
8 9
101 2 3 4
5 6 7
8 9 10 11 12 13
14 15
16 17 18
19 20 21 22 23 241 2
3 4 5 6 7
89
10
11 12 13 14 15 16 1
2 3 4 5 6
78
9 10 11 12
13 14 15 16
1718
19
20 21 22
ECM Terminals
E7
141
2 3
4 5 6 8
7 9
10 12 13 15 16
17 18 19 20 21
22 11
23 24
25 26 27
2817
DI±218
± DIAGNOSTICSENGINE (1MZ±FE)
453 Author: Date:
TERMINALS OF ECM
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
BATT (E7 ± 1) ± E1 (E10 ± 17)B±Y eBRAlways9 ~ 14
+B (E7 ± 16) ± E1 (E10 ± 17)R e BRIG switch ON9 ~ 14
VC (E10 ± 2) ± E2 (E10 ± 18)Y e BRIG switch ON4.5 ~ 5.5
VTA1 (E10 ± 23) LBR
IG switch ON
Throttle valve fully closed0.3 ~ 1.0VTA1 (E10 23)
± E2 (E10 ± 18)Le BRIG switch ON
Throttle valve fully open3.2 ~ 4.9
VG (E10 ± 10)
± E2G (E10 ± 19)P eR±BIdling , A/C switch OFF1.1 ~ 1.5
THA (E10 ± 22) ± E2 (E10 ± 18)L±Y eBRIdling, Intake air temp. 20°C (68°F)0.5 ~ 3.4
THW (E10 ±14) ± E2 (E10 ± 18)G±B eBRIdling, Engine coolant temp. 80°C (176°F) 0.2 ~ 1.0
STA (E7 ± 7) ± E1 (E10 ± 17)GR e BRCranking6.0 or more
#10 (E10 5)IG switch ON9 ~ 14#10 (E10 ± 5)
± E01 (E11 ± 21)L eBRIdlingPulse generation
(See page DI±276)
#20 (E10 6)IG switch ON9 ~ 14#20 (E10 ± 6)
± E01 (E11 ± 21)R eBRIdlingPulse generation
(See page DI±276)
#30 (E11 1)IG switch ON9 ~ 14#30 (E11 ± 1)
± E01 (E11 ± 21)Y eBRIdlingPulse generation
(See page DI±276)
#40 (E11 2)IG switch ON9 ~ 14#40 (E11 ± 2)
± E01 (E11 ± 21)W eBRIdlingPulse generation
(See page DI±276)
#50 (E11 3)IG switch ON9 ~ 14#50 (E11 ± 3)
± E01 (E11 ± 21)R±L eBRIdlingPulse generation
(See page DI±276)
#60 (E11 4)IG switch ON9 ~ 14#60 (E11 ± 4)
± E01 (E11 ± 21)G eBRIdlingPulse generation
(See page DI±276)
IGT1 (E11 ± 11)
± E1 (E10± 17)GR eBRIdlingPulse generation
(See page DI±351)
IGT2 (E11 ± 12)
± E1 (E10 ± 17)BR±Y eBRIdlingPulse generation
(See page DI±351)
IGT3 (E11 ± 13)
± E1 (E10 ± 17)LG±B eBRIdlingPulse generation
(See page DI±351)

FI6448
Intake Air Temp. Sensor
(Inside the Mass Air Flow Meter)ECM
5 V
THA
E2
E1 1
2R
L±Y
BR
E10E1022
18
± DIAGNOSTICSENGINE (1MZ±FE)
DI±229
464 Author: Date:
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTCs P0110 (Intake Air Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunc-
tion), P0120 (Throttle/Pedal Position Sensor/Switch ºAº Circuit Malfunction) and P1410 (EGR Valve
Position Sensor Circuit Malfunction) are output simultaneously, E2 (Sensor Ground) may be open.

Read freeze frame data using TOYOTA hand±held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected, when troubleshooting it is useful for
determining whether the vehicle was running or stopped, the engine warmed up or not, the air±fuel
ratio lean or rich, etc. at the time of the malfunction.

FI6448
Engine Coolant Temp. SensorECM
5V
THW
E2
E1 2
1G±B
BR
E10
14
18
E10
± DIAGNOSTICSENGINE (1MZ±FE)
DI±233
468 Author: Date:
DTC P0115 Engine Coolant Temp. Circuit Malfunction

CIRCUIT DESCRIPTION
A thermistor built into the engine coolant temp. sensor changes the resistance value according to the engine
coolant temp.
The structure of the sensor and connection to the ECM is the same as in the intake air temp. circuit malfunc-
tion shown on page DI±228.
If the ECM detects the DTC P0115, it operates fail±safe function in which the engine coolant temperature
is assumed to be 80°C (176°F).
DTC No.Detection ItemTrouble Area
P0115Open or short in engine coolant temp. sensor circuit

Open or short in engine coolant temp. sensor circuit

Engine coolant temp. sensor

ECM
HINT:
After confirming DTC P0115, use the OBD II scan tool or TOYOTA hand±held tester to confirm the engine
coolant temp. from CURRENT DATA.
Temperature DisplayedMalfunction
±40°C (±40°F)Open circuit
140°C (284°F) or moreShort circuit
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTCs P0110 (Intake Air Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunc-
tion), P0120 (Throttle/Pedal/Position Sensor/Switch ºAº Circuit Malfunction) and P1410 (EGR Valve
Position Sensor Circuit Malfunction) are output simultaneously, E2 (Sensor Ground) may be open.

Read freeze frame data using TOYOTA hand±held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected, when troubleshooting it is useful for
determining whether the vehicle was running or stopped, the engine warmed up or not, the air±fuel
ratio lean or rich, etc. at the time of the malfunction.
DI07I±06

A00214
ON
Engine Coolant
Temp. Sensor
ECM
5 V
E2
2
1
THWE10
E101814
DI±234
± DIAGNOSTICSENGINE (1MZ±FE)
469 Author: Date:
1 Connect OBD II scan tool or TOYOTA hand±held tester, and read value of engine
coolant temperature.
PREPARATION:
(a) Connect the OBD II scan tool or TOYOTA hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the OBD II scan tool or TOYOTA hand±held tester main switch
ON.
CHECK:
Read temperature value on the OBD II scan tool or TOYOTA hand±held tester.
OK:
Same as actual engine coolant temperature.
HINT:

If there is open circuit, OBD II scan tool or TOYOTA hand±held tester indicates ±40°C (±40°F).

If there is open circuit, OBD II scan tool or TOYOTA hand-held tester indicates 140°C (284°F) or more.
NG ±40°C (±40°F) ... Go to step 2.
140°C (284°F) or more ... Go to step 4.
OK
Check for intermittent problems
(See page DI±197).
2 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect the engine coolant temp. sensor connector.
(b) Connect the sensor wire harness terminals together.
(c) Turn the ignition switch ON.
CHECK:
Read temp. value on the OBD II scan tool or TOYOTA
hand±held tester.
OK:
Temperature value: 1405C (2845F) or more
OK Confirm good connection at sensor.
If OK, replace engine coolant temp. sensor.
NG