1999 TOYOTA AVENSIS light

RS0J2–01
H11591
Spiral Cable Combination Meter
(Warning Light)
Front Passenger Airbag Assembly
Side Airbag Assembly (RH)
Side and Curtain Shield Airbag
Sensor Assembly (RH)
Seat Belt Pretensioner (RH) Steering Wheel Pad
(with Airbag)
Side and Curtain Shield Airbag
Sensor Assembly (LH)Seat Belt
Pretensioner (LH)
Side Airbag Assembly (LH)
Airbag Sensor Assembly Front Airbag Sensor (RH)
Front Airbag
Sensor (LH)Curtain Shield Airbag Assembly (RH) Curtain Shield Airbag Assembly (LH)
– SUPPLEMENTAL RESTRAINT SYSTEMWIRE HARNESS AND CONNECTOR
RS–39
WIRE HARNESS AND CONNECTOR
LOCATION

BODY ELECTRICAL
FOG LIGHT SYSTEM BE–1. . . . . . . . . . . . . . . . . . . .
COMBINATION METER BE–2. . . . . . . . . . . . . . . . . .
REFER TO AVENSIS/CORONA REPAIR MANUAL FOR
CHASSIS AND BODY (Pub. No. RM599E)
NOTE: The above pages contain only the points which differ
from the above listed manual.

I12428
ON
OFF
10 11
16
BE196–02
I12429
ON
OFF
10
16
– BODY ELECTRICALFOG LIGHT SYSTEM
BE–1
FOG LIGHT SYSTEM
INSPECTION
1. INSPECT FRONT/REAR FOG LIGHT SWITCH CONTI-
NUITY
Switch positionTester connectionSpecified condition
OFF–No continuity
ON (FRONT)11 – 16Continuity
ON (FRONT/REAR)10 – 11 – 16Continuity
If continuity is not as specified, replace the switch.
2. INSPECT REAR FOG LIGHT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF–No continuity
ON10 – 16Continuity
If continuity is not as specified, replace the switch.

I04818
SPEEDOMETER
TACHOMETER
WATER TEMP.
FUEL
OIL LEVEL
ODO / TRIP
METER
OUTSIDE TEMP.
CLOCK
RHEOSTATLCD
DISPLAY
LCD
DISPLAY S
T
W
FA18
B7
B20 A5
A15
A3
A6
A7
A8
A12
A11
A19
A10
A9
B11
B24
B5
A22
B4
A23
B14
A23
A25
B16
B14
B21
A22
A14VOLTAGE
STABILIZER
B17
B22
B9
B26
A24 Brake Warning
Fuel filter Warning
Discharge Waring
Economy Indicator
Turbo / Glow Plug Indicator
Glow Plug Indicator
ABS Warning
Low Oil Pressure Warning
Check Engine Warning
O / D OFF Indicator
ECT SNOW Indicator
ECT PWR Indicator
Rear Fog Light Indicator
High Beam Indicator
Right Turn Indicator
Left Turn Indicator
Open Door Warning
SRS Warning
Front Fog light Indicator A1
B15
B18A26
B2
A17
B1
B13
B6
B3 B19
BE–4
– BODY ELECTRICALCOMBINATION METER

No.
AGround (Power)
Tacho Pick–UP Sensor
EFI ECU (3S–FE, 2C–TE Engine)
EGR (2C–T Engine)
Vehicle Speed Sensor
EFI ECU
Water Temperature Sender Gauge (2C–T Engine)
Ground (Engine)
Ground
Outside Temperature Sender Gauge
Ground (Fuel)
Fuel Sender Gauge
Ground (Power)
Ground (Speed)
Turn Signal Switch (Right)
Other Parts
Oil Level Warning Switch
O/D OFF Switch
ECT ECU (Gasoline Engine)
Fuel Filter Warning Switch (Diesel Engine)
Glow Plug Timer (Diesel Engine)
EFI ECU (Gasoline Engine)
ECT Pattern Select Switch
ABS ECU
Rear Fog Light Switch 1
3
5
6
7
8
9
10
11
12
14
15
17
18
19
21
22
23
24
25
26Wire Harness Side
1
2
3
4
5
6
7
9
11
13
14
15
16
17
18
19
20
22
24
26Turn Signal Switch (Left)
H–LP Fuse
Front Fog Light Switch
Alternator L Terminal
Brake Fluid Level Warning Switch
Parking Brake Switch
ECU+B Fuse
Taillight Relay
GAUGE Fuse
Ground (Signal)
DOOR Fuse
EFI ECU (Gasoline Engine)
EGR ECU (Diesel Engine)
Headlight Dimmer Switch
Low Oil Pressure Warning Switch
IGN Fuse
Door Courtesy Switch
Airbag ECU
Taillight Relay
GAUGE Fuse
Ground (Signal)
DOOR Fuse
B
– BODY ELECTRICALCOMBINATION METER
BE–5

I01275
Ignition
Switch
BatterySender
Gauge Receiver
Gauge
I01276
Ignition
Switch
BatteryReceiver
Gauge
Test Bulb
(3.4 W)
I01277
Battery Ignition
SwitchWarning Light
Wire Harness Side
1
– BODY ELECTRICALCOMBINATION METER
BE–7
(b) Compare the tester and tachometer indications.
DC 13.5 V 25
C at (77
F)
Standard indicationAllowable range
700630 – 770
1,000900 – 1,100
2,0001,850 – 2,150
3,0002,800 – 3,200
4,0003,800 – 4,200
5,0004,800 – 5,200
6,0005,750 – 6,250
7,0006,700 – 7,300
4. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON and check that the receiver
gauge needle indicates COOL.
(c) Ground terminal on the wire harness side connector
through a 3.4 W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights
up and the receiver gauge needle moves to the hot side.
If operation is as specified, replace the sender gauge.
Then recheck the system.
If operation is not as specified, measure the receiver gauge re-
sistance.
5. INSPECT LOW OIL PRESSURE WARNING LIGHT
(a) Disconnect the connector from the warning switch and
ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
If the warning light does not light up, test the bulb.

BO0IO–04
I12751
Roof Headlining
Sun Visor Opening Trim
Holder Front Pillar Garnish

Windshield
Outside Moulding
Front Pillar Garnish Windshield Wiper Arm
N·m (kgf·cm, ft·lbf) : Specified torque

Non–reusable partWiper Arm
Sun Visor
20 (205, 15)
20 (205, 15)

Dam Inner Rear View Mirror
Cowl Louver Map Light Assembly
Cap
Hood to Cowl Top seal
Stopper
w/ Curtain shield air bag:
Front Pillar Garnish
w/ Curtain shield air bag:
Front Pillar Garnish
– BODYWINDSHIELD
BO–3
WINDSHIELD
COMPONENTS

BO2J0–01
H03507
: Clip
H11626
Pillar Garniush
Cover
2 Clips
I12491
H03502
BO–4
– BODYWINDSHIELD
REMOVAL
1. REMOVE THESE PARS
(a) Remove the front wiper arms.
(b) Remove the weatherstrip.
(c) Remove the cowl louver.
(d) Remove the sun visors and holders.
(e) Remove the map light assembly.
(f) Remove the assist grip.
(g) Remove the upper part of front door opening trims.
(h) w/ Curtain Shield Airbag:
(1) Using a screwdriver, raise the pillar garnish cover.
(2) Remove the bolt, pillar garnish cover and front pillar
garnish.
(3) Remove the 2 bolts.
(4) Pack the airbag with protection cover.
NOTICE:
Protection range is from instrument panel to ceiling.
(i) Remove the front pillar garnishes.
(j) Remove the inner rear view mirror.
(k) Remove the upper back panel hole No.1 cover.
2. REMOVE WINDSHIELD OUTSIDE UPPER MOULDING
Using a knife, cut off the moulding, as shown.
NOTICE:
Do not damage the body with the knife.