1999 TOYOTA AVENSIS headrest

RS0IL–01
H11625
: Specified torque
 Non–reusable partHeadrest
Headrest Support
Lumber Support Adjusting Knob
Seatback Pad
Seatback CoverSeatback
Frame
25 (255, 18)
25 (255, 18)
Side Airbag
Assembly
Front Seat Cushion
Assembly
37 (375, 27)
37 (375, 27)
Front Seat Belt Lap Outer Anchor
42 (430, 31)
Front Seat Cushion Outer Shield
Reclining Adjuster Knob Front Seat Cushion
Inner ShieldHog Ring
N·m (kgf·cm, ft·lbf)Seat Track Cover
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY
RS–9
SIDE AIRBAG ASSEMBLY
COMPONENTS

RS0IM–01
H03408
H03411
H03409
RS–10
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY
REMOVAL
NOTICE:

If the wiring connector of the SRS is disconnected
and the ignition switch is at ON or ACC position, DTCs
will be recorded.

Never use the airbag parts from another vehicle.
When replacing parts, replace them with new parts.
1. REMOVE FRONT SEAT
(a) Remove the reclining adjuster knob and front seat cush-
ion outer shield.
(b) Remove the front seat belt lap outer anchor.
(c) Remove the 2 seat track covers and 4 bolts.
(d) Disconnect the side airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(e) Remove the front seat.
2. REMOVE THESE PARTS FROM FRONT SEAT AS-
SEMBLY
(a) Remove the headrest.
(b) Remove the 2 headrest supports.
(c) Remove the lumber support adjusting knob.
(d) Remove the front seat inner shield.
3. REMOVE SEATBACK FROM SEAT CUSHION AS-
SEMBLY
Using a torx wrench, remove the 4 screws and seatback assem-
bly.
Torx wrench: T40 (Part No.09042–00020 or locally
manufactured tool)
4. REMOVE THESE PARTS FROM SEATBACK FRAME
(a) Disengage the hook of the seatback cover.
(b) Remove the hog rings and seatback cover.
(c) Remove the seatback pad.

RS0IQ–01
H03410
H03411
H03408
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY
RS–19
INSTALLATION
NOTICE:
Never use airbag parts from another vehicle. When replac-
ing parts, replace them with new parts.
1. INSTALL THESE PARTS TO SEATBACK FRAME
(a) Install the seatback pad.
(b) Install the hog rings and seatback cover.
(c) Hang the hook of the seatback cover.
2. INSTALL SEATBACK TO SEAT CUSHION ASSEMBLY
Using a torx wrench, install the 4 screws and seatback assem-
bly.
Torx wrench: T40 (Part No.09042–00020 or locally
manufactured tool)
Torque: 25 N·m (255 kgf·cm, 18 ft·lbf)
3. INSTALL THESE PARTS TO FRONT SEAT ASSEMBLY
(a) Install the 2 headrest supports.
(b) Install the headrest.
(c) Install the lumber support adjusting knob.
(d) Install the front seat inner shield.
4. INSTALL FRONT SEAT
(a) Mount the seat to the vehicle.
(b) Connect the side airbag connector.
(c) Install the outer bolt and inner bolt on the front side after
sliding the seat to the rearmost position.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(d) Tighten the bolts on the rear side temporarily, tighten
them completely starting from the bolt on the inner side.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(e) Install the front seat belt lap outer anchor.
Torque: 42 N·m (430 kgf·cm, 31 ft·lbf)
(f) Install the front seat cushion outer shield and reclining ad-
juster knob.
(g) Install the 2 seat track covers.