1999 TOYOTA AVENSIS differential

IN044–07
IN–34
– INTRODUCTIONTERMS
TERMS
ABBREVIATIONS USED IN THIS MANUAL
AbbreviationsMeaning
ABSAnti–Lock Brake System
A/CAir Conditioner
ACAlternating Current
ACCAccessory
ACISAcoustic Control Induction System
ACSDAutomatic Cold Start Device
A.D.D.Automatic Disconnecting Differential
AHCActive Height Control Suspension
ALRAutomatic Locking Retractor
ALTAlternator
AMPAmplifier
ANTAntenna
APPROX.Approximately
A/TAutomatic Transmission (Transaxle)
AT FAutomatic Transmission Fluid
AUTOAutomatic
BACSBoost Altitude Compensation System
BATBattery
B/LBi–Level
BVSVBimetallic Vacuum Switching Valve
CBCircuit Breaker
CDCompact Disc
CHChannel
CKDComplete Knock Down
COMB.Combination
CPECoupe
CRSChild Restraint System
CTRCenter
DCDirect Current
DIFF.Differential
DIFF. LOCKDifferential Lock
DLCData Link Connector
DSPDigital Signal Processor
DTCDiagnostic Trouble Code
ECTElectronic Control Transmission
ECUElectronic Control Unit
EDUElectronic Driving Unit
EFIElectronic Fuel Injection
E/GEngine
EGRExhaust Gas Recirculation
ELREmergency Locking Retractor
E–VRVElectronic Vacuum Regulating Valve

– INTRODUCTIONTERMS
IN–35
FFFront–Engine Front–Wheel–Drive
FIPGFormed In Place Gasket
FLFusible Link
FrFront
FRFront–Engine Rear–Wheel–Drive
FWDFront–Wheel–Drive
GNDGround
H/BHatchback
HIHigh
HIDHigh Intensity Discharge (Head Lamp)
HTHard Top
HWSHeated Windshield System
IACIdle Air Control
IFSIndependent Front Suspension
IGIgnition
INTIntermittent
I/PInstrument Panel
IRSIndependent Rear Suspension
J/BJunction Block
J/CJunction Connector
LANLocal Area Network
LBLiftback
LCDLiquid Crystal Display
LEDLight Emitting Diode
LHLeft–Hand
LHDLeft–Hand Drive
LOLow
LSDLimited Slip Differential
LSP & PVLoad Sensing Proportioning And Bypass Valve
LSPVLoad Sensing Proportioning Valve
MAPManifold Absolute Pressure
MAX.Maximum
MICMicrophone
MILMalfunction Indicator Lamp
MIN.Minimum
MPMultipurpose
MPIMultipoint Electronic Fuel Injection
MPXMultiplex Communication System
M/TManual Transmission
NNeutral
No.Number
O2SOxygen Sensor
O/DOverdrive
OPTOption
P & BVProportioning And Bypass Valve
PCSPower Control System

PP27T–01
– PREPARATIONMANUAL TRANSAXLE (E251)
PP–1
MANUAL TRANSAXLE (E251)
SST (Special Service Tools)
09223–15020Oil Seal & Bearing ReplacerDifferential case oil seal
09308–00010Oil Seal PullerOutput shaft front bearing outer
race
09316–20011Transfer Bearing ReplacerDifferential case tapered roller
bearing
09316–60011Transmission & Transfer Bearing
Replacer
(09316–00011)Replacer Pipe
(09316–00021)Replacer ”A”
(09316–00041)Replacer ”C”1st gear
No.1 hub sleeve
Differential case tapered roller
bearing outer race
(09316–00071)Replacer ”F”Output shaft front bearing
09506–30012Differential Drive Pinion Rear
Bearing Cone ReplacerOutput shaft rear bearing
09506–35010Differential Drive Pinion Rear
Bearing ReplacerNo.2 hub sleeve
3rd gear
Input shaft rear bearing
1st gear bearing inner race
09608–00081Differential Side Bearing Cone
ReplacerInput shaft oil seal
09612–65014Steering Worm Bearing PullerInput shaft bearing
Differential case tapered roller
bearing outer race

PP–2
– PREPARATIONMANUAL TRANSAXLE (E251)
09950–00020Bearing Remover
09950–00030Bearing Remover AttachmentOutput shaft front bearing
09950–30011Puller A Set5th driven gear
No.3 clutch hub
09950–40011Puller B SetDifferential case tapered roller bearing
09950–60010Replacer Set
(09951–00580)Replacer 58Input shaft bearing
09950–60020Replacer Set No.2
09950–70010Handle Set
(09951–07150)Handle 150

PP0VD–02
– PREPARATIONMANUAL TRANSAXLE (E251)
PP–3
RECOMMENDED TOOLS
09025–00010Torque Wrench (30 kgf–cm)Differential preload
09031–00030Pin Punch .
09040–00011Hexagon Wrench Set .
09042–00040Torx Socket T50 .
09042–00050Torx Socket T45 .
09082–00040TOYOTA Electrical Tester.
09258–00030Hose Plug Set .
09905–00012Snap Ring No.1 Expander .
09905–00013Snap Ring Pliers .

PP0VF–02
– PREPARATIONMANUAL TRANSAXLE (E251)
PP–5
LUBRICANT
ItemCapacityClassification
Manual transaxle oil (w/ Differential oil)3.9 liters (4.1 US qts, 3.4 Imp. qts)API GL–4 or GL–5
SAE 75W–90

PP27U–01
PP–6
– PREPARATIONSUSPENSION AND AXLE
SUSPENSION AND AXLE
SST (Special Service Tools)
09240–00020Wire Gauge Set
09316–60011Transmission & Transfer Bearing
Replacer
(09316–00041)Replacer ”C”
09520–01010Drive Shaft Remover Attachment
09520–24010Differential Side Gear Shaft
Puller
(09520–32040)Shocker Set
09521–24010Drive Shaft Boot Clamping Tool
09608–16042Front Hub Bearing Adjusting Tool
(09608–02021)Bolt & Nut
(09608–02041)Retainer
09710–30021Suspension Bushing Tool Set
(09710–03121)Bushing Remover Base

– SERVICE SPECIFICATIONSMANUAL TRANSAXLE (E251)
SS–5
Input shaft snap ring thickness Mark
No.3 clutch hub a
b
c
d
e
f
g
h
j
Ball bearing 1
2
3
4
5
6
7
8
1.75 mm (0.0689 in.)
1.80 mm (0.0709 in.)
1.85 mm (0.0729 in.)
1.90 mm (0.0748 in.)
1.95 mm (0.0768 in.)
2.00 mm (0.0787 in.)
2.05 mm (0.0807 in.)
2.10 mm (0.0827 in.)
2.15 mm (0.0847 in.)
2.35 mm (0.0925 in.)
2.40 mm (0.0945 in.)
2.45 mm (0.0965 in.)
2.50 mm (0.0984 in.)
2.55 mm (0.1004 in.)
2.60 mm (0.1024 in.)
2.65 mm (0.1043 in.)
2.70 mm (0.1063 in.)
Differential pinion to side gear backlash STD0.05 – 0.20 mm (0.0020 – 0.0079 in.)
Differential side gear thrust washer thickness
0.80 mm (0.0315 in.)
0.90 mm (0.0354 in.)
1.00 mm (0.0394 in.)
1.10 mm (0.0433 in.)
1.20 mm (0.0472 in.)
1.30 mm (0.0512 in.)
1.40 mm (0.0551 in.)
Differential case side bearing preload (at starting)
New bearing (Output shaft preload plus)
Reused bearing (Output shaft preload plus)
0.2 – 0.3 N·m (1.8 – 3.5 kgf·cm, 1.6 – 3.0 in.·lbf)
0.1 – 0.2 N·m (1.1 – 2.2 kgf·cm, 1.0 – 1.9 in.·lbf)
Differential side bearing adjusting shim thickness Mark
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
G
H
2.00 mm (0.0787 in.)
2.05 mm (0.0807 in.)
2.10 mm (0.0827 in.)
2.15 mm (0.0846 in.)
2.20 mm (0.0866 in.)
2.25 mm (0.0886 in.)
2.30 mm (0.0906 in.)
2.35 mm (0.0925 in.)
2.40 mm (0.0945 in.)
2.45 mm (0.0965 in.)
2.50 mm (0.0984 in.)
2.55 mm (0.1004 in.)
2.60 mm (0.1024 in.)
2.65 mm (0.1043 in.)
2.70 mm (0.1063 in.)
2.75 mm (0.1083 in.)
2.80 mm (0.1102 in.)
2.85 mm (0.1122 in.)