1999 SUBARU LEGACY rear

C: MT VEHICLES (OUTBACK)
B2M1765A
(1) Pitching stopper
(2) Spacer
(3) Cushion C
(4) Front plate
(5) Damper (LTD model)
(6) Rear cushion rubber
(7) Rear crossmember(8) Cushion D
(9) Center crossmember
(10) Rear plate
(11) Front crossmemberTightening torque: N´m (kg-m, ft-lb)
T1:
7.4±2.0 (0.75±0.2, 5.4±1.4)
T2:33±5 (3.4±0.5, 24.6±3.6)
T3:37±10 (3.8±1.0, 27±7)
T4:49±5 (5.0±0.5, 36.2±3.6)
T5:57±10 (5.8±1.0, 42±7)
T6:69±15 (7.0±1.5, 51±11 )
T7:137±20 (14±2, 101±14)
5
[C2C0]2-11COMPONENT PARTS
2. Transmission Mounting

D: AT VEHICLES (OUTBACK)
S2M0197A
(1) Pitching stopper
(2) Rear cushion rubber
(3) Crossmember
(4) StopperTightening torque: N´m (kg-m, ft-lb)
T1:
37±10 (3.8±1.0, 27±7)
T2:38±15 (3.9±1.5, 28±11 )
T3:49±5 (5.0±0.5, 36.2±3.6)
T4:57±10 (5.8±1.0, 42±7)
T5:69±15 (7.0±1.5, 51±11 )
6
2-11[C2D0]COMPONENT PARTS
2. Transmission Mounting

(1) Disconnect the following connectors.
H2M2433A
(1) Front oxygen sensor connector
(2) Rear oxygen sensor connector
(California spec. vehicles)
(3) Engine harness connectors
(4) Engine ground terminal
(5) Alternator connector and termi-
nal
(6) A/C compressor connectors
(With A/C)
10
2-11[W1B0]SERVICE PROCEDURE
1. Engine

B2M2776AS2M0204A
12) Remove power steering pump from bracket.
(1) Loosen lock bolt and slider bolt, and remove
front side V-belt.
G2M0286
(2) Remove pipe with bracket from intake mani-
fold.
B2M2309
(3) Remove bolts which install power steering
pump from bracket.
S2M0086
(4) Place power steering pump on the right side
wheel apron.
S2M0087
13) Remove front exhaust pipe and center
exhaust pipe.
(1) Lift-up the vehicle.
(2) Disconnect connector from rear oxygen
sensor. (Except 2500cc California spec.
vehicles)
B2M0335
14
2-11[W1B0]SERVICE PROCEDURE
1. Engine

(3) Remove nuts which install front exhaust
pipe onto engine.
G2M0290
(4) Separate center exhaust pipe from rear
exhaust pipe.
S2M0052
(5) Remove bolt which installs center exhaust
pipe on hunger bracket.
B2M0313
(6) Take off front and center exhaust pipes.
CAUTION:
Exhaust pipe will drop when all bolts are
removed. So, hold it when removing the last
bolt.14) Remove nuts which hold lower side of trans-
mission to engine.
B2M2790
15) Remove nuts which install front cushion rub-
ber onto front crossmember.
G2M0293
16) Separate torque converter from drive plate.
(AT vehicles)
(1) Lower the vehicle.
(2) Remove service hole plug.
(3) Remove bolts which hold torque converter
to drive plate.
S2M0207
(4) Remove other bolts while rotating the
engine using ST.
2200 cc vehicles:
ST 499977300 CRANK PULLEY WRENCH
2500 cc vehicles:
ST 499977100 CRANK PULLEY WRENCH
15
[W1B0]2-11SERVICE PROCEDURE
1. Engine

7) Install canister and bracket.
(1) Install power stering pump on bracket, and
tighten bolts.
Tightening torque:
39
±10 N´m (4.0±1.0 kg-m, 29±7 ft-lb)
S2M0086
(2) Install power steering pipe bracket on right
side intake manifold, and install spark plug
codes.
B2M2309
(3) Install front side V-belt, and adjust it.

G2M0286
8) Tighten nuts which hold lower side of transmis-
sion to engine.
Tightening torque:
50
±4 N´m (5.1±0.4 kg-m, 36.9±2.9 ft-lb)
B2M2790
9) Tighten nuts which install front cushion rubber
onto crossmember.
Tightening torque:
69
±15 N´m (7.0±1.5 kg-m, 51±11 ft-lb)
CAUTION:
Be sure to tighten front cushion rubber mount-
ing bolts in the innermost elliptical hole in the
front crossmember.
G2M0303
10) Install front exhaust pipe and center exhaust
pipe.
11) Connect the following hoses.
(1) Fuel delivery hose, return hose and evapo-
ration hose
(2) Heater inlet and outlet hoses
(3) Brake booster vacuum hose
12) Connect the following connectors.
(1) Engine ground terminal
(2) Engine harness connectors
(3) Front oxygen sensor connector
(4) Rear oxygen sensor connector (California
spec. vehicles)
(5) Alternator connector and terminal
(6) A/C compressor connectors (With A/C)
13) Connect the following cables.
(1) Accelerator cable
(2) Cruise control cables (With cruise control)
(3) Clutch cable (2200 cc MT vehicles)
18
2-11[W1C0]SERVICE PROCEDURE
1. Engine

2. Transmission
A: GENERAL PRECAUTION
(1) Remove or install transmission in an area
where chain hoists, lifting devices, etc. are avail-
able for ready use.
(2) Be sure not to damage coated surfaces of
body panels with tools or stain seats and windows
with coolant or oil. Place a cover over fenders, as
required, for protection.
(3) Prior to starting work, prepare the following:
Service tools, clean cloth, containers to catch cool-
ant and oil, wire ropes, chain hoist, transmission
jacks, etc.
(4) Lift-up or lower the vehicle when necessary.
Make sure to support the correct positions. to 1-3 [G700].>
B: REMOVAL
1) Open front hood fully, and support with stay.
2) Disconnect battery ground terminal.
3) Remove air intake duct and chamber. (Except
2200 cc California spec. vehicles) [W1A0].>
4) Install air intake duct with air cleaner case.
(2200 cc California spec. vehicles) [W1A0].> and
5) Remove chamber stay.
IMT vehicles
S2M0210
IAT vehicles
S6M0023
6) Disconnect the following connectors.
(1) Oxygen sensor connector
S2M0200A
(1) Front oxygen sensor connector
(2) Rear oxygen sensor connector (California spec.
vehicles)
(2) Transmission harness connector (AT
vehicles)
S2M0212A
(3) Transmission ground terminal
(4) Neutral position switch connector (MT
vehicles)
(5) Back-up light switch connector (MT
vehicles)
B2M0337
21
[W2B0]2-11SERVICE PROCEDURE
2. Transmission

13) Set ST.
ST 41099AA020 ENGINE SUPPORT ASSY
NOTE:
Also is available Part No. 927670000.
G2M0313
14) Remove bolt which holds right upper side of
transmission to engine.
B2M2791
15) Remove exhaust system.
(1) Lift-up the vehicle.
(2) Remove under cover.
(3) Disconnect connector from rear oxygen
sensor. (Except California spec. vehicles)
B2M0335
(4) Remove nuts which install front exhaust
pipe onto engine.
G2M0290
(5) Separate rear exhaust pipe from center
exhaust pipe.
B2M0055
(6) Remove bolt which installs center exhaust
pipe to hanger bracket.
S2M0206
(7) Take off front and center exhaust pipes.
23
[W2B0]2-11SERVICE PROCEDURE
2. Transmission