1999 SUBARU FORESTER fuse

2.
No.1 Door
\(Door Disconnect
2 Door
\(Door a.
b.
side.Connect
Functionally
3 Door
handle
to a.
b.
adjustmentConnect
Remove
Adjust
is
4 Door
set
\(Keyless a.
b.
adjustedSame
Same
5 Child
b.Refer
6 Inner
mountingEliminate
upper
7
8 Auto
inner Auto
toSame
3.
Symptom
All
move. Driver
doesDriver
dow
move
down.Neither
side
move.
Battery
Fuse
Circuit
Main
Sub \(2\)
Motor
Motor \(3\)
Regulator \(4\)
Power
Ground
Harness \(
39
[K300]5-2DIAGNOSTICS
3.

2.
No.1 Door
\(Door Disconnect
2 Door
\(Door a.
b.
side.Connect
Functionally
3 Door
handle
to a.
b.
adjustmentConnect
Remove
Adjust
is
4 Door
set
\(Keyless a.
b.
adjustedSame
Same
5 Child
b.Refer
6 Inner
mountingEliminate
upper
7
8 Auto
inner Auto
toSame
3.
Symptom
All
move. Driver
doesDriver
dow
move
down.Neither
side
move.
Battery
Fuse
Circuit
Main
Sub \(2\)
Motor
Motor \(3\)
Regulator \(4\)
Power
Ground
Harness \(
39
[K300]5-2DIAGNOSTICS
3.

3. ADJUSTABLE SHOULDER ANCHOR
1) Remove shoulder anchor bolt. [W3A1].>
2) Remove center pillar cover. [W5A1].>
3) Remove center pillar upper trim. [W5A1].>
4) Remove adjustable shoulder anchor assembly.
S5M0235
5) Install in the reverse order of removal.
4. Rear Seat Belt
A: REMOVAL AND INSTALLATION
WARNING:
Replace rear seat belt worn by occupants of a
vehicle that has been in a serious accident. The
entire assembly should be replaced even if
damage is not obvious.
1. OUTER BELT (OUTSIDE)
1) Remove rear cushion.
2) Remove rear backrest.
3) Remove rear quarter upper trim and rear quar-
ter lower trim.
4) Remove anchor cover and then remove anchor
bolt.
5) Remove bolt and nut and then detach outer belt
assembly.
S5M0236
6) Install in the reverse order of removal.
NOTE:
Ensure that seat belt is properly reeled on and off
after installation of ELR.
CAUTION:
IBe extremely careful not to confuse center
seat anchor plate with outer seat anchor plate
during installation.
IEnsure that seat belts are free from twisting
after installation.
IEnsure that tongues, buckles and belts are
properly placed on seat.
11
[W4A1]5-3SERVICE PROCEDURE
4. Rear Seat Belt

3. ADJUSTABLE SHOULDER ANCHOR
1) Remove shoulder anchor bolt. [W3A1].>
2) Remove center pillar cover. [W5A1].>
3) Remove center pillar upper trim. [W5A1].>
4) Remove adjustable shoulder anchor assembly.
S5M0235
5) Install in the reverse order of removal.
4. Rear Seat Belt
A: REMOVAL AND INSTALLATION
WARNING:
Replace rear seat belt worn by occupants of a
vehicle that has been in a serious accident. The
entire assembly should be replaced even if
damage is not obvious.
1. OUTER BELT (OUTSIDE)
1) Remove rear cushion.
2) Remove rear backrest.
3) Remove rear quarter upper trim and rear quar-
ter lower trim.
4) Remove anchor cover and then remove anchor
bolt.
5) Remove bolt and nut and then detach outer belt
assembly.
S5M0236
6) Install in the reverse order of removal.
NOTE:
Ensure that seat belt is properly reeled on and off
after installation of ELR.
CAUTION:
IBe extremely careful not to confuse center
seat anchor plate with outer seat anchor plate
during installation.
IEnsure that seat belts are free from twisting
after installation.
IEnsure that tongues, buckles and belts are
properly placed on seat.
11
[W4A1]5-3SERVICE PROCEDURE
4. Rear Seat Belt