1999 MITSUBISHI LANCER EVOLUTION VI voltage

REAR AXLE – Troubleshooting 27-28
CHECK AT AYC-ECU TERMINALS
TERMINAL VOLTAGE LISTING

The voltage is to be measured across each terminal and ground terminal.

Fig. below shows the arrangement of the terminals.
Terminal
No.Check itemCheck requirementNormally
1Lateral acceleration sensorIgnition switch: ON2.4 – 2.6 V
(horizontal position)
2Longitudinal acceleration
sensor ground
Lateral acceleration sensor
groundAt all times0 V
3Longitudinal acceleration
sensorIgnition switch: ON2.4 – 2.6 V
(horizontal position)
4Steer sensor (ST-2)Engine: Idle speed
Turn steering wheel slowly.0 V ↔ approx. 3 V
flashing
5Steer sensor (ST-1)Engine: Idle speed
Turn steering wheel slowly.0 V ↔ approx. 3 V
flashing
6*1FR wheel speedVehicle stationary1 V or less
Forward vehicle slowly.0 – 5 V
7*1FL wheel speedVehicle stationary1 V or less
Forward vehicle slowly.0 – 5 V
8*1RR wheel speedVehicle stationary1 V or less
Forward vehicle slowly.0 – 5 V
9*1FL wheel speedVehicle stationary1 V or less
Forward vehicle slowly.0 – 5 V
10Diagnosis selection inputWhen MUT-II is connected1 V or less
When MUT-II is disconnectedSystem voltage
11Stop lamp switchIgnition switch:
ON
Stop lamp switch: ONSystem voltage
ON
Stop lamp switch: OFF1 V or less
12*1ABS monitorWhen ABS monitor is activatedSystem voltage
When ABS monitor is deactivated1 V or less

REAR AXLE – Troubleshooting 27-29
Terminal
No.Normally Check requirement Check item
17Steer sensor (ST-N)Engine:
Idle speed
Steering wheel: Neutral position0.5 V or less
Idle speed
Steering wheel: Turned 90 from
neutral position2.5 – 3.5 V
18TPSIgnition switch:
ON
Accelerator pedal: Fully closed0.3 – 1.0 V
ON
Accelerator pedal: Fully open4.5 – 5.0 V
23Diagnosis data input/outputWhen MUT-II is connectedSerial communica-
tion with MUT-II
When MUT-II is disconnected1 V or less
24Idle position switchIgnition switch:
ON
Accelerator pedal: Fully closed2 V or less
ON
Accelerator pedal: Fully open4.5 – 5.0 V
25Accumulator pressure
switchIgnition switch:
ONAccumulator internal pressure:
Low2 V or less
Accumulator internal pressure:
HighSystem voltage
26ECU groundAt all times0 V
31AYC-ECU power supplyIgnition switch: ONSystem voltage
Ignition switch: OFF0 V
35AYC motor relayIgnition switch:
ON
When motor is energizedSystem voltage
ON
When motor is deenergized2 V or less
36AYC warning lampIgnition switch:
ON
When lamp is OFFSystem voltage
ON
When lamp is ON2 V or less
37Directional control valve
(right)
Ignition switch:
ON
Right clutch: ONSystem voltage
(right)ON
Right clutch: OFF0 V
38Proportioning valveIgnition switch:
ONAYC-ON0 V to system volt-
age
AYC-OFF0 V
39ECU backup power supplyAt all timesSystem voltage
45Directional control valve
(left)
Ignition switch:
ON
Left clutch: ONSystem voltage
(left)ON
Left clutch: OFF0 V
46ECU groundAt all times0 V
NOTE
*1: Indicates the vehicles with ABS.

REAR AXLE – On-vehicle Service 27-37
WHEEL SPEED SENSOR OUTPUT VOLTAGE
MEASUREMENT
1. Lift up the vehicle and release the parking brake.
2. Disconnect the AYC-ECU harness connector and take
measurements on the harness side connector.
Caution
Insert the probe from the harness side with the double
lock of the connector unlocked. Inserting it to the
terminal side could result in poor contact.
3. Turn the wheel to be tested at about 1/2 to one
revolution/sec. and check for the output voltage using
a circuit tester (AC mV range) or oscilloscope.
Terminal nos.
Front LHFront RHRear LHRear RH
7698
20192221
Output voltage:
When circuit tester is used: 70 mV or more
When oscilloscope is used: 200 mVp-p or more
(4) If the output voltage is lower than the above value, it
is probably attributable to the following faults. Check or
replace the wheel speed sensor as necessary.

Excessive clearance between the pole piece and rotor
of the wheel speed sensor

Defective wheel speed sensor
Waveform Check Using Oscilloscope
Check the harness and connector of the wheel speed sensor
for connection. Then, use an oscilloscope to check for output
voltage waveform of each sensor as follows.
Start the engine and monitor the sensor by turning the wheel;
for a driving wheel, let it turn by shifting into the 1st gear
and for a driven wheel turn it manually at a constant speed.
NOTE
(1) Waveform may be observed by actually running the
vehicle.
(2) The output voltage is low when the wheel speed remains
low and builds up as the wheel speed increases.
AYC-ECU connector harness side
When turned manually
At idle (5 to 6 km/h)
1st gear

REAR AXLE – On-vehicle Service 27-38
Waveform Observation Points
SymptomProbable causeAction
Waveform amplitude is too small, or no
waveform.Defective wheel speed sensorReplace sensor.
Waveform amplitude varies greatly. (No
problem ifthe smallest amplitude is 100
Excessive axle hub lateral and radial runoutReplace hub.
problem if the smallest amplitude is 100
mV or more)Poor AYC-ECU groundingRepair.
Noise on waveform or disturbed
waveform
Open-circuited sensorReplace sensor.
waveform
Open-circuited harnessRepair harness.
Improperly mounted wheel speed sensorCorrect sensor installation.
Missing or collapsed ABS rotor toothReplace ABS rotor.
Caution
Since the wheel speed sensor cable follows the movement of the front or rear suspension, it
may be open-circuited only when the vehicle is run on rough roads and not on ordinary road.
The wheel speed sensor output voltage waveform should therefore be checked also by rocking
the sensor harness so that driving on rough roads may be simulated.
ACTION WHEN BATTERY RUNS OUT
When the engine is started using a booster cable where the
battery has completely run down and you attempt to start
the vehicle without waiting for the battery to recover a certain
charge, the engine can misfire and you just cannot start to
move it. In such cases, charge the battery sufficiently; or,
remove the AYC fusible link from the engine compartment
relay box to make AYC inactive before attempting to start
the vehicle. When the fusible link is removed, the AYC warning
lamp lights up. After the battery has been recharged, fit the
fusible link back again and start the engine to ensure that
the AYC warning lamp is off.AYC fusible link

REAR AXLE – Sensor Relay / AYC-ECU27-42
INSPECTION
1. LONGITUDINAL AND LATERAL ACCELERATION
SENSOR CHECK
Refer to GROUP 35B – Acceleration Sensor.
2. AYC RELAY CONTINUITY CHECK
Battery voltageTerminal No.
1345
When not energized
When energized
AYC-ECU
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation

Front Floor Console Removal and Installation
5 Nm
AYC-ECU
5 Nm

BODY – Keyless Entry System42-3
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between receiver and earth
NG
Repair
OK
Replace the ETACS-
ECU.
NG
Repair
OK
Replace the transmitter.NGReplace the receiver.
NG
Check the harness wire.

Between key reminder switch and receiver

Between key reminder switch and earthNG
Repair
OK
Check trouble symptoms.
OK
Check the following connectors:
B-50, B-84, D-01NG
Repair
OK
Key reminder switch continuity check (Refer to GROUP 54 – Ignition
Switch.)NG
Replace
NG
Check the harness wire.

Between receiver and door switchNG
Repair
OK
Check trouble symptoms.
OK
Check the following connectors:
D-01, D-03, D-06, D-17, F-12, F-26NG
Repair
NG
Check the harness wire.

Between ETACS-ECU and receiver
OK
Door switch continuity checkNG
Replace
OK
Check trouble symptoms.
OK
Measure at the receiver connector D-01.

Disconnect the connector, and measure at harness side.

Voltage between 12 and body earth

Voltage between 14 and body earth
OK:System voltageNGCheck the connectors:
B-77, D-01
OK
Check trouble symptoms.
OK
Measure at the receiver connector D-01.

Disconnect the connector, and measure at the harness side.

Continuity between 20 and body earth
OK:ContinuityNGCheck the following connectors:
B-50, D-01
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between ignition switch and receiver

Between fusible link No.1 and receiver
OK
Check trouble symptoms.
Measure at the receiver connector D-01.

Disconnect the connector, and measure at the harness side.

Voltage between 9 and body earth

Voltage between 10 and body earth
OK:System voltageNGCheck the following connectors:
B-49, B-73, B-75, B-76
From previous page

BODY – Keyless Entry System42-4
INSPECTION PROCEDURE 2
All of the doors can be locked and unlocked using the
transmitter, but the room lamp does not flash or
illuminate. (However, the room lamp operates normally
when the doors are opened and closed.)
Probable cause
If the room lamp operates normally when the doors are opened and closed, the cause
of the problem may be a malfunction of the receiver or a malfunction of the harness
between the room lamp the receiver.
Malfunction of receiver

Malfunction of connector or wiring harness
NG
Repair
NG
Check the harness wire between room lamp and receiver, and
repair if necessary.
OK
Replace the receiver.
OK
Check trouble symptoms.
Measure at the receiver connector D-01.

Disconnect the connector, and measure at the harness side.

Voltage between 11 and body earth
OK:System voltageNGCheck the following connectors:
B-80, D-01
INSPECTION PROCEDURE 3
Secret codes cannot be registered.
Probable cause
The cause may be a malfunction of the diagnosis connector, a malfunction of the
power supply or earth circuit of the receiver, a malfunction of the earth circuit or
a malfunction of the diagnosis output circuit.
Malfunction of receiver

Malfunction of MUT-II

Malfunction of connector or wiring harness
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between receiver and diagnosis connector
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between fusible link No.1 and diagnosis connector
OK
Check trouble symptoms.NGCheck the harness wire, and repair if necessary.

Between diagnosis connector and earth
Ye s
To next page
NG
Check the following
connectors:
B-22, B-50NG
Repair
OK
Measure at the diagnosis
connector B-22.

Continuity between 4
and body earth

Continuity between 5
and body earth
OK:ContinuityOKReplace MUT-II.
OK
Check trouble symptoms.
No
Measure at the diagnosis
connector B-22

Voltage between 16
and body earth
OK:System voltageNGCheck the following connectors:
B-22, B-49, B-75
OK
Can the MUT-II communicate with other systems?
OK
Check trouble symptoms.
Measure at the diagnosis connector B-22 and the receiver connector
D-01.

Disconnect the connector, and measure at harness side.

Continuity between following terminals:
OK:Continuity
7 – 1 NGCheck the following connectors:
B-22, D-01

BODY – Keyless Entry System42-5
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between fusible link No.1 and receiver

Between ignition switch and receiver
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between receiver and earth
OK
Replace the receiver.
OK
Check trouble symptoms.
OK
Measure at the receiver connector D-01.

Disconnect the connector, and measure at the harness side.

Between 20 and body earth
OK:ContinuityNGCheck the following connectors:
B-50, D-01
OK
Check trouble symptoms.
Measure at the receiver connector D-01.

Disconnect the connector, and measure at the harness side.

Voltage between 9 and body earth

Voltage between 10 and body earth
OK:System voltageNGCheck the following connectors:
B-49, B-75, D-01
From previous page
INSPECTION OF RECEIVER TERMINAL VOLTAGE
TerminalSignal nameConditionsTerminal voltage
2Door switchOne or more doors are open (Door switch: ON)0 V
All doors are closed (Door switch: OFF)System voltage
6Door lock actuator
switch (driver’s side)
LOCK5 V and pulse output*
switch (driver’s side)
UNLOCK0 V
7Diagnosis changeover
input
When MUT-II is connected0 V
input
When MUT-II is disconnectedSystem voltage
8Key reminder switchOFF (When ignition key is inserted)5 V and pulse output*
ON (When ignition key is removed)0 V
9Ignition switchIgnition switch: ACC or ONSystem voltage
Ignition switch: OFF0 V
10Receiver power supplyAt all timesSystem voltage
11Room lamp outputOne or more door are open (Door switch: ON)0 V
All doors are closed (Door switch: OFF)System voltage