1998 VOLKSWAGEN JETTA Service Manual

Downloaded from www.Manualslib.com manuals search engine 01-321


Switch to measuring range:
Resistance measurement (200 /20 M )
Test
step V.A.G
1598
sockets Item
tested Test conditions
- Additional operationsSpecification
Measures for
deviations from
specification
20 11 or 15 Data
bus
wiring
Ignition switched
off

Measuring set
range to 200
- Disconnect multi-pin
connection from a
control module which
is connected via data
bus wiring:
- Connect test box
V.A.G 1598/36

- Check data bus
wiring for open circuit Max. 1.5
Electrical Wiring
Diagrams,
Troubleshooting &
Component Locations
binder - Check wiring using
wiring diagram
Test step 20: Continued on next page
Стр. 34из 38 Electrical check of Mark 60

Downloaded from www.Manualslib.com manuals search engine 01-322


Continuation of test step 20

Test
step V.A.G
1598
sockets Item
tested
Test conditions
- Additional
operations Specification
Measures for deviations
from specification

- Set measuring
range to 20 M
- Remove fuse S9

- Check wiring for
short circuit to
positive or Ground




Electrical Wiring
Diagrams,
Troubleshooting &
Component Locations
binder - Check wiring using
wiring diagram
Стр. 35из 38 Electrical check of Mark 60

Downloaded from www.Manualslib.com manuals search engine 01-323


Switch to measuring range:
Voltage measurement (20 V =)
Test
step V.A.G
1598
sockets Item tested
Test conditions
- Additional
operations Specification
Measures for
deviations from
specification
21 - Voltage
supply for
V.A.G 1551,
connector
T16
1)
Ignition
switched off
- Connect hand
multimeter V.A.G
1526 to connector
T16
1) using adapter
set V.A.G 1594 10.0 -14.5 V

Electrical Wiring
Diagrams,
Troubleshooting &
Component
Locations binder - Check wiring using
wiring diagram
1) Diagnosis connector contact assignment Page 01-292
Стр. 36из 38 Electrical check of Mark 60

Downloaded from www.Manualslib.com manuals search engine 01-324


Switch to measuring range:
Resistance measurement 200
Test
step V.A.G
1598
sockets Item tested Test conditions
- Additional
operations Specification
Measures for
deviations from
specification
22 - Resistance
of K wire for
V.A.G 1551,
connector
T16
1)
Ignition switched
off
- Disconnect multi-pin
connector from ABS
control module
(w/EDL) -J104
- Connect test box
V.A.G 1598/36
- Connect hand
multimeter V.A.G
1526 to contacts
T16/7
1) and T47/2 of
multi-pin connector of
ABS control module
(w/EDL) -J104- using
cables from adapter
set V.A.G 1594 Max. 1.5
Electrical Wiring
Diagrams,
Troubleshooting &
Component
Locations binder - Check wiring
using wiring
diagram
1) Diagnosis connector contact assignment Page 01-292
Стр. 37из 38 Electrical check of Mark 60

Downloaded from www.Manualslib.com manuals search engine 01-325


Switch to measuring range:
Resistance measurement (200 )
Test
step V.A.G
1598
sockets Item tested Test
conditions
- Additional
operations Specification
Measures for
deviations from
specification
23 14 + 38 Coding bridge for
ABS and
ABS/EDL/ASR
front wheel drive
Ignition
switched
off 0.0 -1.0
12 + 38 Coding bridge for
ABS/EDL/ASR/ESP
front wheel drive
12 + 9 Coding bridge for
ABS/EDL/ASR/ESP
4MOTION

Electrical Wiring
Diagrams,
Troubleshooting &
Component
Locations binder - Check wiring
using wiring
diagram
Стр. 38из 38 Electrical check of Mark 60

Downloaded from www.Manualslib.com manuals search engine 01-326


Definitions
These explanations refer only to this assembly
group: ABS On Board Diagnostic (OBD). These
definitions are not necessarily generally valid.

ABS
Anti-locking brake system. Further information
on the ABS can be found in the relevant self-
study programs.

Display group number Read measured
value block

ASR
Traction Control System

Data bus
Transportation of data. To do this the electrical
signals are brought into a certain format (BUS).
Further information can be found in Self-study
programs. Also called CAN Bus.

Data bus low (high)
The voltage used to transport the data is low
(high). Further information can be found in Self-
study programs.

Speed sensor
Sends speed signals to control module.
Стр. 1из 6 Definitions

Downloaded from www.Manualslib.com manuals search engine 01-327



EBD
Electronic brake pressure distribution

EDL
Electronic differential lock

On Board Diagnostic (OBD)
The capability of the control module:

Recognize Diagnostic Trouble Codes
(DTCs)

React to DTCs

Store DTCs
and make them available in the Measured
value block. Further information on this can be
found in Self-study programs and test unit
instruction manual.

Performing On Board Diagnostic (OBD)
Connecting the Scan Tool to be able to check
the DTC memory. Further information on this
can be found in Self-study programs and test
unit instruction manual.

Performing electrical check
A targeted check of the electronic components
by performing certain measurements.
Стр. 2из 6 Definitions

Downloaded from www.Manualslib.com manuals search engine 01-328



ESP
Electronic Stabilization program

ESP-Sensor unit -G419-, vehicles from
02.02
The sensor for transverse acceleration -G200-,
the sender for rotation rate -G202- and the
sensor for longitudinal acceleration sensor -
G251- (4MOTION vehicles) are assembled
together in a housing.

No communication
There is no connection for exchanging
information between the control modules.

Sender for rotation rate -G202-
Recognizes the rotational movement of the
vehicle along its vertical axis in relation to
vehicle speed.

Longitudinal acceleration sensor -G251-
Determines the correct speed for 4MOTION
vehicles

Steering angle sensor -G85-
Determines the angle and direction of steering
lock (driver's wish). Data is transferred to
control module via data bus wiring.

Short to Ground
Current flows incorrectly to Ground without
supplying a consumer.
Стр. 3из 6 Definitions