1998 VOLKSWAGEN JETTA Service Manual

Downloaded from www.Manualslib.com manuals search engine 01-126


Switch to measuring range:
Resistance measurement (200 /20 M )
Test
step V.A.G
1598
sockets Item
tested Test conditions
- Additional operationsSpecification
Measures for
deviations from
specification
19 11 +10 Data
bus
wiring
Ignition switched
off

Set to measuring
range 200


- Disconnect multi-pin
connection from a
control module which
is connected via data
bus wiring:

- Connect test box
V.A.G 1598/21

- Check data bus
wiring for open circuit max. 1.5
Electrical Wiring
Diagrams,
Troubleshooting &
Component Locations
binder - Check wiring using
wiring diagram
Test step 19: Continued on next page
Стр. 25из 31 ABS, ABS/EDL and ABS/EDL/ASR ITT Mark 20 IE, electrical check

Downloaded from www.Manualslib.com manuals search engine 01-127


Continuation of test step 19
Test
step V.A.G
1598
sockets Item
tested
Test conditions
- Additional
operations Specification
Measures for deviations
from specification
19

Set to
measuring
range 20 M

- Remove fuse S9

- Check wiring for
short circuit to
positive or earth




Electrical Wiring
Diagrams,
Troubleshooting &
Component Locations
binder - Check wiring using
wiring diagram
Стр. 26из 31 ABS, ABS/EDL and ABS/EDL/ASR ITT Mark 20 IE, electrical check

Downloaded from www.Manualslib.com manuals search engine 01-128


Switch to measuring range:
Resistance measurement (200 /20 M )
Test
step V.A.G
1598
sockets Item tested Test conditions
- Additional
operations Specification
Measures for
deviations from
specification
20 -
Longitudinal
acceleration
sensor -
G251- wiring
Ignition switched
off
Select 200
measuring range
- Disconnect
connector for
longitudinal
acceleration sensor -
G251-
- Disconnect multi-pin
connector T25 from
ABS control module
(w/EDL) -J104-
- Connect test box
V.A.G 1598/21

- Check wiring
between multi-pin
connector for
longitudinal
acceleration sensor -
G251- and multi-pin
connector for ABS
control module
(w/EDL) -J104- for
open circuit max. 1.5
Electrical Wiring
Diagrams,
Troubleshooting &
Component
Locations binder - Check wiring
using wiring
diagram
Test step 20: Continued on next
page.
Стр. 27из 31 ABS, ABS/EDL and ABS/EDL/ASR ITT Mark 20 IE, electrical check

Downloaded from www.Manualslib.com manuals search engine 01-129


Continuation of test step 20
Test
step V.A.G
1598
sockets Item
tested
Test conditions
- Additional
operations Specification
Measures for deviations
from specification


Set to
measuring
range 20 M

- Remove fuse S9

- Check wiring for
short circuit to
positive or Ground




Electrical Wiring
Diagrams,
Troubleshooting &
Component Locations
binder - Check wiring using
wiring diagram
Стр. 28из 31 ABS, ABS/EDL and ABS/EDL/ASR ITT Mark 20 IE, electrical check

Downloaded from www.Manualslib.com manuals search engine 01-130


Functional check: ESP Control lamp -K155
Test
step V.A.G
1598
sockets Item
tested
Test
conditions
- Additional
operations Specification
Measures for
deviations from
specification
21 - Function of
ESP
Control
lamp -
K155-
Switch
ignition on ESP Control lamp -
K155- lights up for 2
seconds and goes
out again

Electrical Wiring
Diagrams,
Troubleshooting &
Component Locations
binder
Repair Manual,
Body Interior,Repair
Group 70 - Check wiring using
wiring diagram
- Malfunction in
instrument cluster
Стр. 29из 31 ABS, ABS/EDL and ABS/EDL/ASR ITT Mark 20 IE, electrical check

Downloaded from www.Manualslib.com manuals search engine 01-131


Brake light switch, adjusting

Vehicle up to my 02.00
Repair Manual, Brake System, Repair
Group 46; Installing brake light switch
Remove brake light switch to adjust.

- Disconnect connector from brake light
switch.
- Remove brake light switch by turning to
left through 90 .
- Pull brake light switch plunger fully out.
- Press brake pedal down as far as
possible by hand.
- Guide brake light switch through
assembly opening and reinstall by
turning 90 to right.
- Release brake pedal.
- Connect brake light switch connector.
- Install driver's side stowage tray if
necessary.
- Operate brake pedal.
Brake lights light up.
- Take foot off brake pedal.
Brake lights do not light up.
Стр. 30из 31 ABS, ABS/EDL and ABS/EDL/ASR ITT Mark 20 IE, electrical check

Downloaded from www.Manualslib.com manuals search engine 01-132



Vehicle from my 03.00

- Pull out brake light switch plunger to full
extension.

- Keep brake pedal in up position (IMPORTANT!
hold pedal up if necessary while installing
switch).

- Guide switch through mounting hole (only fits in
one position).

- Seat switch fully into opening (pressing plunger
against pedal to adjust.

-
Seat switch by turning it 45 clockwise. This
action also turns the plunger shoe into the
correct orientation to make electrical contracts in
switch operate as well as locks in plunger
adjustment.

- Connect brake light switch connector.

- Operate brake pedal to verify proper function.

- Reinstall lower cover panel.
Стр. 31из 31 ABS, ABS/EDL and ABS/EDL/ASR ITT Mark 20 IE, electrical check

Downloaded from www.Manualslib.com manuals search engine 01-133


ABS Mark 60 On Board
Diagnostic (OBD), vehicles
from my 10.00
There are four versions of the ABS Mark 60.

ABS

ABS/EDL/ASR

ABS/EDL/ASR/ESP with front wheel drive

ABS/EDL/ASR/ESP with 4MOTION
Each version has its own control module. The
control modules can be coded accordingly
through coding bridges via tester VAS 5051 or
V.A.G 1551.
The ESP (Electronic Stabilization Program) is
an electronic dynamics Program (EDP). It
stabilizes the vehicle when oversteering or
understeering. The ESP works over the whole
speed range. If the ESP is regulating the
system the ESP warning lamp will flash 3 times
per second.

The ESP is a further extension of the
familiar vehicle safety systems.
ESP increases control over the vehicle in
critical situations. It reduces the danger of
skidding and increases the steering control
when compared with familiar vehicle safety
systems.
Стр. 1из 10 ABS Mark 60 On Board Diagnostic (OBD), vehicles from my 10.00