1998 TOYOTA LAND CRUISER wheel torque

SA15Z-04
F04386
SST
F05217
F05080
Matchmarks
- SUSPENSION AND AXLEREAR DIFFERENTIAL CARRIER (w/ LSD)
SA-141
2091 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE 2 REAR WHEELS
Torque: 131 N´m (1,340 kgf´cm, 97 ft´lbf)
2. DRAIN HYPOID GEAR OIL
Torque: 49 N´m (500 kgf´cm, 36 ft´lbf)
3. DISCONNECT BRAKE LINES
(a) Using SST, disconnect the brake line and remove the clip.
SST 09023-00100
Torque: 15 N´m (150 kgf´cm, 11 ft´lbf)
(b) Employ the same manner described above to the other
side.
4. DISCONNECT PARKING BRAKE CABLES
(a) Remove the 2 clips, pin and disconnect the parking brake
cable from the bellcrank.
(b) Employ the same manner described above to the other
side.
5. REMOVE AXLE SHAFTS
(a) Remove the 4 nuts.
Torque: 123 N´m (1,250 kgf´cm, 90 ft´lbf)
(b) Pull out the axle shaft assembly and remove the O-ring.
NOTICE:
Be careful not to damage the oil seal.
(c) Employ the same manner described above to the other
side.
6. DISCONNECT REAR PROPELLER SHAFT
(a) Place matchmarks on the propeller shaft and differential
flange.
(b) Remove the 4 nuts, bolts, washers and disconnect the
propeller shaft.
Torque: 106 N´m (1,080 kgf´cm, 78 ft´lbf)
(c) Support the propeller shaft securely.

SA16M-02
F04393
F04400
- SUSPENSION AND AXLEREAR STABILIZER BAR
SA-185
2135 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE REAR WHEELS
Torque: 131 N´m (1,340 kgf´cm, 97 ft´lbf)
2. SUPPORT REAR AXLE HOUSING WITH JACK
3. DISCONNECT LH AND RH STABILIZER BAR BRACK-
ETS
Remove the 4 bolts and disconnect the LH and RH stabilizer bar
brackets.
Torque: 18 N´m (185 kgf´cm, 13 ft´lbf)
4. REMOVE STABILIZER BAR
(a) Remove the 4 bolts and stabilizer bar with the bushings
and brackets.
Torque: 18 N´m (185 kgf´cm, 13 ft´lbf)
(b) Remove the 2 brackets and 2 bushings from the stabilizer
bar.
5. REMOVE BOTH STABILIZER BAR LINKS FROM STA-
BILIZER BAR
(a) Remove the nut, 3 retainers, 2 cushions and disconnect
the stabilizer bar link from the bracket.
Torque: 15 N´m (150 kgf´cm, 11 ft´lbf)
(b) Employ the same manner described above to the other
side.
(c) Remove the 2 nuts, bolts and stabilizer bar links.
Torque: 26 N´m (270 kgf´cm, 19 ft´lbf)
(d) Remove the 2 collars and cushions.

SA16J-02
F04397
F04398
SA-182
- SUSPENSION AND AXLEREAR UPPER AND LOWER CONTROL ARM
2132 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 131 N´m (1,340 kgf´cm, 97 ft´lbf)
2. SUPPORT REAR AXLE HOUSING WITH JACK
3. REMOVE UPPER CONTROL ARM
(a) Disconnect the ABS speed sensor wire harness.
(b) RH side:
Remove the bolt and heat insulator.
Torque: 18 N´m (185 kgf´cm, 13 ft´lbf)
(c) Remove the 2 nuts, washers, bolts and upper control arm.
Torque: 150 N´m (1,530 kgf´cm, 111 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nuts.
4. REMOVE LOWER CONTROL ARM
Remove the 2 nuts, washers, bolts and lower control arm.
Torque: 150 N´m (1,530 kgf´cm, 111 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nuts.

SA15J-02
F04387
F04389
F04390
- SUSPENSION AND AXLEREAR WHEEL HUB BOLT
SA-93
2043 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REAR WHEEL HUB BOLT
REPLACEMENT
1. REMOVE REAR WHEEL
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the 2 bolts, brake caliper and disc.
(b) Support the brake caliper securely.
3. REMOVE HUB BOLT
Using a brass bar and hammer, remove the hub bolt.
4. INSTALL HUB BOLT
Install a washer and nut to a new hub bolt, as shown in the il-
lustration, and install the hub bolt by torquing the nut.
5. INSTALL DISC AND BRAKE CALIPER
Install the disc and brake caliper with the 2 bolts.
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
6. INSTALL REAR WHEEL
Torque: 131 N´m (1,340 kgf´cm, 97 ft´lbf)