1998 TOYOTA LAND CRUISER wheel torque

SR-66
- STEERINGPOWER STEERING GEAR
2275 Author
: Date
:
2004 LAND CRUISER (RM1071U)
10. INSTALL NO. 1 ENGINE UNDER COVER
Tighten the 7 bolts.
11. POSITION FRONT WHEELS FACING STRAIGHT
AHEAD
HINT:
Do it with the front of the vehicle jacked up.
12. CENTER SPIRAL CABLE (See page SR-24)
13. INSTALL STEERING WHEEL
(a) Align the matchmarks on the wheel and steering column
main shaft.
(b) Temporarily tighten the wheel set nut.
(c) Connect the connector.
14. BLEED POWER STEERING SYSTEM (See page
SR-4)
15. CHECK STEERING WHEEL CENTER POINT
16. TORQUE STEERING WHEEL SET NUT
Torque: 50 N´m (510 kgf´cm, 37 ft´lbf)
17. INSTALL STEERING WHEEL PAD (See page SR-24)
18. CHECK FRONT WHEEL ALIGNMENT (See page
SA-6)
19. PERFORM ZERO POINT CALIBRATION OF YAW RATE
AND DECELERATION SENSORS (See page DI-505)

F17184
Brass Bar
F17596
F05049
F17597
SST
Fulcrum
Length
SR-64
- STEERINGPOWER STEERING GEAR
2273 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(c) Using a brass bar and hammer, stake the washer.
NOTICE:
Avoid any impact to the rack.
(d) Employ the same manner described above to the other
side.
13. INSTALL RH AND LH RACK BOOTS, CLAMPS AND
CLIPS
(a) Ensure that the tube hole is not clogged with grease.
HINT:
If the tube hole is clogged, the pressure inside the boot will
change after it is assembled and the steering wheel is turned.
(b) Install the boot.
NOTICE:
Be careful not to damage or twist the boot.
(c) Using pliers tighten a new clamp, as shown in the illustra-
tion.
(d) Employ the same manner described above to the other
side.
14. INSTALL 2 TURN PRESSURE TUBES
Using SST, install the tube.
SST 09023-38200
Torque: 23 N´m (230 kgf´cm, 17 ft´lbf)
HINT:

Use a torque wrench with a fulcrum length of 300 mm
(11.81 in.).

This torque value is effective in case that SST is parallel
to a torque wrench.

SR0M7-04
F05613
Steering Wheel Pad
50 (510, 37)
Steering Wheel Lower
No. 2 Cover
Torx Screw
8.8 (90, 78 in.´lbf)
Combination Switch
(w/ Spiral Cable)
Steering Wheel
Torx Screw
8.8 (90, 78 in.´lbf)
Steering Wheel Lower
No. 3 Cover
Column Upper Cover
Column Lower Cover
Steering Column Assembly
25 (260, 19)
Thrust Stopper
Sliding Yoke
34 (350, 25)Hose Clamp
No. 2 Hole Cover
Hole Cover
No. 2 Intermediate
Shaft AssemblyCluster Finish Panel
Lower No. 1 Panel
34 (350, 25)
LH Lower Panel
Hood Lock Release Lever
Fuel Lid Release Lever
No. 2 Heater to Register
DuctClip
Cowl Trim
Scuff Plate
N´m (kgf´cm, ft´lbf) : Specified torque
- STEERINGPOWER TILT AND POWER TELESCOPIC STEERING
COLUMNSR-27
2236 Author
: Date
:
2004 LAND CRUISER (RM1071U)
POWER TILT AND POWER TELESCOPIC STEERING
COLUMN
COMPONENTS

R12473
SR0M0-06
F03748
- STEERINGSTEERING WHEEL
SR-9
2218 Author
: Date
:
2004 LAND CRUISER (RM1071U)
STEERING WHEEL
INSPECTION
1. CHECK STEERING WHEEL FREEPLAY
(a) Stop the vehicle and face the tires straight ahead.
(b) Rock the steering wheel gently up and down with a finger
lightly, check the steering wheel freeplay.
Maximum freeplay: 40 mm (1.58 in.)
2. CHECK STEERING EFFORT
(a) Center the steering wheel.
(b) Remove the steering wheel pad (See page SR-14).
(c) Start the engine and run it at idle.
(d) Measure the steering effort in both directions.
Steering effort (Reference):
4.9 N´m (50 kgf´cm, 43 in.´lbf)
HINT:
Be sure to consider the tire type, pressure and contact surface
before making your diagnosis.
(e) Torque the steering wheel set nut.
Torque: 50 N´m (510 kgf´cm, 37 ft´lbf)
(f) Install the steering wheel pad (See page SR-24).

F16017
Steering Column
Upper Cover
New Marked
Line
Steering Wheel
R00429
Marked Line
F16018
- STEERINGSTEERING WHEEL
SR-1 1
2220 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(d) Turn the steering wheel to its straight position.
HINT:
Refer to the upper surface of the steering wheel, steering spoke
and SRS airbag line for the straight position.
(e) Draw a new line on the masking tape of the steering wheel
as shown in the illustraion.
(f) Measure the distance between the 2 lines on the masking
tape of the steering wheel.
(g) Convert the measured distance to steering angle.
Measured distance 1 mm (0.04 in.) = Steering angle
approximately 1 deg.
HINT:
Make a note of the steering angle.
2. ADJUST STEERING ANGLE
(a) Draw a line on the RH and LH tie rod and rack ends where
it can easily be seen.
(b) Using a paper gauge, measure the distance from RH and
LH tie rod ends to the rack end screws.
HINT:

Measure the RH side and LH side.

Make a note of the measured values.
(c) Remove the RH and LH boot clips from the rack boots.
(d) Loosen the RH and LH lock nuts.
(e) Turn the RH and LH rack end by the same amount (but
in different directions) according to the steering angle.
1 turn 360 deg. of rack end (1.5 mm (0.059 in.) horizon-
tal movement) = 12 deg. of steering angle
(f) Tighten the RH and LH lock nuts.
Torque: 55 N´m (560 kgf´cm, 41 ft´lbf)
NOTICE:
Make sure that the difference in length between RH and LH
tie rod ends and rack end screws are within 1.5 mm (0.059
in.).
(g) Install the RH and LH boot clips.
(h) Perform the zero point calibration of yaw rate and decel-
eration sensors (See page DI-505).

SR0M1-04
F05612
Steering Wheel Lower
No. 2 Cover
50 (510, 37)Steering Wheel PadColumn Upper Cover
Column Lower Cover
Steering Column Assembly
Steering Wheel Lower
No. 3 Cover
Torx Screw
8.8 (90, 78 in.´lbf)
Steering Wheel
Combination Switch
(w/ Spiral Cable)
Thrust Stopper Sliding Yoke
34 (350, 25)
25 (260, 19)
Hose Clamp
No. 2 Hole Cover
Hole Cover
13 (130, 9)
No. 2 Intermediate Shaft
AssemblyCluster Finish Panel
34 (350, 25)
LH Lower Panel
Lower No. 1 Panel
Hood Lock Release Lever
Fuel Lid Release Lever
No. 2 Heater to Register
Duct
Clip
Cowl Trim
Scuff Plate
N´m (kgf´cm, ft´lbf) : Specified torque
Torx Screw
8.8 (90, 78 in.´lbf)
SR-12
- STEERINGTILT STEERING COLUMN
2221 Author
: Date
:
2004 LAND CRUISER (RM1071U)
TILT STEERING COLUMN
COMPONENTS

F17248
Mark
- STEERINGTILT STEERING COLUMN
SR-25
2234 Author
: Date
:
2004 LAND CRUISER (RM1071U)
12. INSTALL COWL TRIM
Install the cowl trim with the clip.
13. INSTALL SCUFF PLATE
14. INSTALL SPIRAL CABLE (See page BE-31)
15. INSTALL COMBINATION SWITCH WITH SPIRAL
CABLE
(a) Install the combination switch with the 3 screws.
(b) Connect the airbag connector.
(c) Tilt steering column:
Connect the 3 connectors.
(d) w/ Power tilt and power telescopic steering column:
Connect the 5 connectors.
16. INSTALL UPPER AND LOWER COLUMN COVERS
Install the upper and lower column covers with the 3 screws.
17. CENTER SPIRAL CABLE
(a) Check that the front wheels are facing straight ahead.
(b) Turn the cable counterclockwise by hand until it becomes
harder to turn the cable.
(c) Then rotate the cable clockwise about 2.5 turns to align
the mark.
HINT:
The cable will rotate about 2.5 turns to either left or right of the
center.
18. INSTALL STEERING WHEEL
(a) Align the matchmarks on the steering wheel and main
shaft.
(b) Install the steering wheel set nut.
Torque: 50 N´m (510 kgf´cm, 37 ft´lbf)
(c) Connect the connector.
19. INSTALL STEERING WHEEL PAD
NOTICE:

Never use airbag parts from another vehicle. When
replacing parts, replace with new ones.

Make sure the wheel pad is installed to the specified
torque.

If the wheel pad has been dropped, or there are
cracks, dents or other defects in the case or connec-
tor, replace the wheel pad with a new one.

When installing the wheel pad, take care that the wir-
ings do not interfere with other parts and are not
pinched between other parts.

F04780
Torx
ScrewScrew
Case SR-26
- STEERINGTILT STEERING COLUMN
2235 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(a) Connect the connector.
(b) Connect the airbag connector.
(c) Install the pad after confirming that the circumference
groove of the torx screw is caught on the screws case.
(d) Using a torx socket wrench, torque the 2 screws.
Torque: 8.8 N´m (90 kgf´cm, 78 in.´lbf)
(e) Install the steering wheel lower No. 2 and No. 3 covers.
20. CHECK STEERING WHEEL CENTER POINT