1998 JAGUAR X308 ECU

Installation


7. Position trim finisher for a ccess and withdraw and discard
release button harness grommet from trunk lid.
8. Remove trim finisher from trunk lid.

9. Carefully remove seal from trim finisher.

10. Slacken and remove screws securing release button assembly
to trim finisher and remove release button from finisher.
1. Fit and fully seat release button in trim finisher and fit and
tighten securing screws.
2. Apply suitable adhesive to contac t area of trim finisher and fit
and align seal to finisher.
3. Position trim finisher and pass release button harness through
trunk lid aperture.

4.
Fit and fully seat a new harn ess grommet in trunk lid.
5. NOTE: Fit new pressed steel fasteners on Jaguar models.
Align and fully seat trim finisher on trunk lid and fit and fully
tighten securing nuts/fasteners.
6. Connect release button harness multiplug and position harness
in retaining clip.
7. Position and fully seat trunk li d trim pad and secure with new
fir tree fasteners.
8. Fit finisher over trunk latch, fi t and tighten securing bolts and
fit bolt covers..
9. Fit trunk lamp assemblies. Refer to 86.45.16.
10. Connect ground cable to batt ery terminal and fit battery
cover. Refer to 86.15.15.

Exterior Trim and Ornamentation - Radiator Grille
Removal and Installation
Removal
Installation



1. Slacken and remove the two scre ws securing top of grill to
surround.

2. Lift grill to withdraw retainin g lugs from slots and remove
grill from vehicle.
3. Remove and discard the two ny lon screw inserts from top of
surround (adapters for su percharged models).
4. Repeat above steps to remove grill on opposite side.
1. Fit new screw inserts/adapters to top of grill surround.
2. Fit grill lower lugs into suurround slots.
3. Fit and tighten the two screws securing top of grill to surround.

4. Repeat above steps to instal l grill on opposite side.

Exterior Trim and Ornamentation - Radiator Grille Bezel
Removal and Installation
Removal
Installation

1.
Remove radiator grills for access. Refer to 76.55.03.

2. Slacken and remove the two screws securing each end of
surround to BIW and remove surround from vehicle.
3. Remove and discard the two nylon screw inserts from each
side of BIW.
1. Fit new screw inserts to BIW locations.
2. Position grill surround on BIW and fit and tighten securing
screws.
3. Fit radiator grills. Refer to 76.55.03.

Rear View Mirrors - Auto-Dimming Interior Mirror
Removal and Installation
Removal
Installation

1.
Remove roof console for access and disconnect interior mirror
harness multiplugs. Refer to 76.13.69.90.

2. Remove upper cover from mirror stem.
3. Remove rain sensor unit. Refer to Section 501.16.

4. CAUTION: When removing mirror from base, care must
be exercised to ensure that base is not detached from windshield.
Applying firm downward pre ssure, remove mirror assembly
from base.
1. Position mirror at bottom of base and apply firm upward
pressure to fully seat and secure in position.
2. Install upper cover to mirror stem.
3. Position roof console at head er and connect mirror harness
multiplugs.
4. Install rain sensor unit. Refer to Section 501.16.
5. Install roof console. Refer to 76.13.69.

Rear View Mirrors - Exterior Mirror
Removal and Installation
Removal
Installation

1.
Fully open door glass and ease top of door casing away from
door Refer to 76.34.01.
2. Remove door frame cheater trim and memory foam for access.

3. Remove mirror assembly from door.
1. Disconnect mirror harness multiplug.
2. Supporting mirror, slacken and remove securing screw and remove mirror assembly from door.

1. Fit exterior mirror assembly to door.
1. Pass harness and multiplu g through cheater aperture
and position mirror foot on cheater, locating the two
dowels correctly and ensuring correct seating on seal.

Fit and tighten the mirror assembly securing screw.
Connect mirror assembly harness multiplug, position in
door and reposition door foam.
2. Fit memory foam and door frame cheater trim.
3. Close door glass.
4. Fit top of door casing. Refer to 76.34.01.

Rear View Mirrors - Exterior Mirror Cover
Removal and Installation
Removal
Installation

1.
Remove exterior mirror glass. Refer to 76.10.53.

2. Remove exterior mirror cap.
1. From housing interior, pr ess out the three cap dowels
complete with securing clips.
Remove mirror cap from casing.
Remove and discard the securing clips.

1. Fit cap to mirror housing.
1. Fit and fully seat new cap securing clips in mirror base.
2. Align mirror cap dowels with the securing clips and press firmly into place.
2. Fit mirror glass. Refer to 76.10.53.

Rear View Mirrors - Exterior Mirror Motor
Removal and Installation
Removal
Installation

1.
Remove exterior mirror glass. Refer to 76.10.53.

2. Remove movement moto r pack from housing.
1. Slacken and remove the three self tapping screws
securing motor pack to housing.
2. Partially withdraw motor pack, disconnect multiplug and remove motor pack from mirror housing.

1. Fit glass movement motor pack to housing.
1. Connect multiplug and posi tion motor pack in housing
ensuring that harness is correctly routed and not
trapped.
2. Fit and tighten the three se lf tapping screws securing
motor pack to housing and fold-back mounting.
2. Fit exterior mirror glas s. Refer to 76.10.53.