1998 JAGUAR X308 ECU

clip
.

5. With draw parkin
g brake cable th
rough equalizer (LH side cable
only).
6. Lower four-post lift.
7. Raise rear of vehicle to workin g height and support on stands.
Refer to section 100-02.
8. Remove rear wheel. Refer to section 204-04.

9. Posit i
on special tool (204-1
95) on hub studs and install
securing nuts.

10 . Slac
ken but do not remove hub to axle shaft securing nut.
11. Remove nuts and withdraw special tool (204-195) from hub.
12. Remove rear brake disc. Refer to 70.10.13.
13. Remove parking brake shoe s. Refer to 70.40.05.
14. Remove wheel speed sensor.

Disc
onnect wheel speed sensor harness connector.
R

emove sensor securing bolt
and withdraw sensor from
hub carrier.

15
.
Sever and discard wheel speed sensor harness tie strap and
position harness for access.

16
.
Remove hub nut and collar.
Re
move nut.
Re

move locating collar.

17
.
Install thread protec tor on axle shaft.
18. Release hub from axle shaft.
Position hu
b puller on hub studs. (204-011)
Inst

all securing nuts.
Progres

sively tighten
puller center bolt to release hub from
axle shaft splines.

19. Remove h
ub puller an
d thread protector.
Re
move securing nuts and
release puller from hub.
Re
move thread protecto
r from axle shaft.

20 . Relea
se parking brake cable
from suspension mounting
bracket.
Remove cable reta ining clip.

Draw c
a
ble through suspension mounting bracket
aperture.

21 . Remove parking brake cable to hu
b carrier grommet.

22 . Remove back plate.
Remove two bolts and two scre ws securing back plate
to
hub carrier.
With draw back plate
complete
with parking brake cable.
23. Mark wishbone at pivot pin eccentric flange marker to aid
installation.

14. Inst
all wheel speed sensor on hub carrier.
Posit
i
on sensor on hub carrier
and install and tighten bolt
to 7-10Nm.
Conne ct
wheel speed sensor harness to sensor.

15 . Using new ti
e strap, secure wh
eel speed sensor harness to
hub carrier.
16. Install handbrake shoes. Re fer to operation 70.40.05.
17. Install brake disc. Refer to operation 70.10.13.

18 . Posit
ion special tool (204-195)
on hub studs and install nuts.
19. Tighten hub nut to 304-336Nm.

20
.
Remove nuts and withdraw special tool (204-195) from hub.
21. Install rear wheel. Refer to Section 204-04.
22. Remove stands and lower vehi cle onto wheels. Refer to
section 100-02.
23. Raise vehicle on four-post lift.

24
.
Route parking brake cable through suspension mounting
bracket and secure with clip.

25
.
Route parking brake cable through equalizer (LH side cable
only).

26
.
Install parking brake cabl e in connecting clip.
27. Adjust parking brake cable. Refer to 70.35.10.
28. Lower four-post lift
29. Apply parking brake.
30. Carry out rear wheel alignm ent check and adjust as


necessary. Refer
t
o 204-02 Specification section.

cli
p.

5. With
draw parking brake cable th
rough equalizer (LH side cable
only).
6. Lower four-post lift.
7. Raise rear of vehicle to workin g height and support on stands.
Refer to section 100-02.
8. Remove rear wheel. Refer to section 204-04.

9. Posit
ion special tool (204-1
95) on hub studs and install
securing nuts.

10
.
Slacken but do not remove hub to axle shaft securing nut.
11. Remove securing nuts from stud s and withdraw special tool
(204-195) from hub.
12. Remove rear brake disc. Refer to 70.10.13.
13. Remove parking brake shoe s. Refer to 70.40.05.
14. Remove wheel speed sensor.

Disconne
ct wheel speed sensor harness connector.
Re

move sensor securing bolt
and withdraw sensor from
hub carrier.

15 . Re
move wheel speed sensor harness tie strap and position
harness for access.

16 . Mark wi
shbone at pivot pin eccentric flange marker to aid
installation.

17 . Remove n
ut and washer from pivot pin.
18. Remove hub securing nut and collar.
Remo
ve nut.
Remove l

ocating collar.

19
.
Install a thread protector on axle shaft.

20
.
Release hub from axle shaft.
Position hu
b puller on hub studs. (204-011)
Inst

all securing nuts.
Progres

sively tighten
puller center bolt to release hub from
axle shaft splines.
21. Remove nuts and release puller from hub.
22. Remove thread protec tor from axle shaft.

23
.
Release handbrake cable from suspension mounting bracket.
Remove cable reta
ining clip.
Draw c

able through suspension mounting bracket
aperture.
24. Remove parking brake cable to hub carrier grommet.