1998 JAGUAR X308 rear seat

Seating - Rear Seat Cushion Cover
Removal and Installation
Removal
1. Remove rear heel boards.
2. Remove rear seat cushion. Refer to 76.70.37.
3. Place seat cushion inverted on clean work surface.

4. Remove and discard the eight hog rings securing cover at each
seat belt anchor aperture.

5. Remove and discard hog rings se curing outer edges of cover
and cushion to frame.

6. Remove and discard two hog ri ngs securing centre panel
overlap plastic edge fastener and release fastener from frame.

7. Withdraw centre overlap thro ugh cushion for access.and
remove and discard hog rings secu ring horizontal seam of right
hand panel to cushion.

14.
Fit rear seat cushion to ve hicle. Refer to 76.70.37.
15. Fit rear heel boards.

Seating - Rear Seat Cushion Heater Mat
Removal and Installation
Removal
Installation

1.
Remove the rear seat cushion. Fo r additional information, refer
to the procedure in this section: Rear Seat Cushion
.

2. Remove the seat cushion cover.

3. Detach the seat cushion heater element electrical connectors.

4. Remove the seat cushion heater element.
1. To install, reverse the removal procedure.

Seating - Rear Seat Head Restraint
Removal and Installation
Removal
Installation

1.
Remove rear heel boards.
2. Remove rear seat cushion.
3. Remove rear seat belt escu tcheon. Refer to 76.73.18.
4. Fully lower headrests.
5. Remove rear seat squa b. Refer to 76.70.38.

6. Place seat squab inverted on clean work surface and remove
headrest retaining clips.
7. Withdraw headrest from seat squab.
1. Position headrest fully lowered on seat squab.
2. Fit and fully seat headrest retaining clips.
3. Fit rear seat squab asse mbly. Refer to 76.70.38.
4. Fit rear seat belt escutc heons. Refer to 76.73.18.
5. Fit rear seat cushion. refer to 76.70.37.
6. Fit rear heel boards.
7. Raise headrests to original positions.

Seating - Rear Seat Track
Removal and Installation
Removal
1. Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.

2. Slacken and remove the two seat cushion front securing bolts
and nuts.

3. Move the seat cushion forward to release it from the two frame
rear tangs.

4. Disconnect the cushion heater harness multiplug and remove
cushion from seat frame.

5. Remove and discard pl astic scrivet securing lower end of side
trim to inner wheela rch stud and withdraw trim from stud.

Installation


12. Disconnect seat motor and squab heater harness multiplugs.

13. Slacken and remove four bolts securing seat frame to floor
and remove seat from vehicle.
1. Position seat in vehi cle and fit but do not tighten four bolts
securing frame to floor.
2. Fit and fully tighten the two bolt s securing squab frame to rear
panel.
3. Fully tighten bolts securing frame to floor.
4. Connect seat motor and squab heater harness multiplugs.
5. Position side trim panel and carefully pass seat belt lower
anchor through escutcheon and trim aperture.
6. Fit and tighten seat belt anchor securing bolt.
7. Position side trim and push do wnwards to engage keyhole on
squab outer fixing.
8. Position trim lower end over st ud and fit and fully seat new
scrivet.
9. Position seat cushion for access and connect cushion heater
harness multiplug.
10. Push seat cushion rearwards to engage it in rear securing
lugs.

Installation



1. Install and fully seat switchpack in seat mounting.
2. Raise cushion pad for access to rear of switchpack and connect
harness multiplug.
3. Release cushion pad and secure cushion cover front elastic
retaining straps to seat frame.
4. Pull cushion cover over cushion pad and fully seat edge
retaining strip on seat frame.
5. Install seat in vehicle. Refer to 76.70.01.
6. Connect ground cable to battery terminal and fit battery cover.
Refer to 86.15.15.

Installation

1. Position motor/regulator assembly in door and fit onto glass.
2. Align motor with door holes and fit and tighten securing screws
and nuts.
3. Position glass lift guide and fi t but do not tighten securing
screws.
4. Align glass lift guide with marked screw positions and fully
tighten screws.
5. Remove tape securing glass to door frame.
6. Connect a 12volt supply to the motor multiplug and power the
glass fully down and up.

7. Draw lines on the glass exterior as follows:
Horizontally along the line of the door frame top.
Vertically along the line of the B post.
8. Power glass down and check that lines indicate it is seating
squarely in the seal.
9. If necessary adjust the glass position as follows:
Slacken the glass lift guid e rear securing screw.
• NOTE: If glass is inclin ed rearwards, move guide
downwards in slot. If glass is inclined forwards, move
guide upwards in slot.
Reposition the lift guide and tighten the securing screw.
Re-check glass alignment.
10. Clean lines from glass.
11. Power window to fully up position
12. Repeat steps 7 and 8.
13. When glass alignment is satisf actory, thoroughly clean off
lines.
14. Power window to fully closed po sition and disconnect 12volt