1998 ACURA INTEGRA rear

)7.Carefully pull the glass out through the window slot.
NOTE:
a Take care not to drop the glass inside the door.
a Check the guide pin for damage, and replace it
it necessary.
NOTEr Scribe a line around the guide pin to show
the original location.
GUIDE PIN
GUIDE PINMOUNTING BOLT6 r 1.0 mm3 N.m lO.3 kgl m,2 tbf.trl
GUIDE PIN
GUIDE PIN
SEAL
20-11
Disconnect the connector, then remove the regula-
tor through the center hole in the door.
NOTE: Scribe a line around the rear roller guide bolt
to show the original adiustment.


: Bolt locations, 6
6x1.0mmI N.m {0.8 kgf m6lbt.ftl
REGULATOR
(cont d)

Outer Molding Replacement
CAUTION: Wear gloves to remove the outer molding.
1. Remove the power mirror (see page 20-49).
2. Lower the glass.
3. Starting at the rear, pry the outer molding up and
detach the clips, then remove the outer molding.
NOTE: Take care not to twist or scratch the outer
mold ing.
A : Clip locations, 6
OUTERMOLDING
CLIP
4. Installation is the reverse of the removal procedure.
NOTE:
a It necessary, replace any damaged clips.
a When installing, align the rear edge ot the outer
molding with the rear edge of the door.
OUTER MOLDING
i ---.-__ \.='''- c;,-1
i--,'
NOTE:
a Before installing the inner weatherstrip, apply clear
sealant to locations @ on the door as shown.
a It necessary, replace any damaged clips.
Sealant: Cemedine #8500, or equivalent
>: Clip locations, 21L l : Clip location, 1
.e
Inside
INNERWEATHERSTRIP
WEATHERSTRIP
DD
oo(,)
INNER WEATHERSTRIP

Replacement (cont'dl
L Grease all the sliding surJaces of the regulatof and
glass guide where shown.
V : Adjusting boltlocations.3
4\
A
or.,-6- thread
61SILICONE GREASE
tF ht\_:-Use liquidlock.
10.
't1.
12.
r 3.
Roll the glass up and down to see if it moves lreely
without binding. Also make sure that there is no
clearance between the glass and weatherstrip when
the glass is closed. Adjust the position ot the glass
as necessary (see page 20-40).
Attach the door harness to the door correctly (see
page 20 221.
Disconnect the power window switch from the door
harness, ihen inslall the power window switch on
the door panel (see page 20 41).
When reinstalling the plastic cover, apply adhesive
along the edge where neccessary to maintain a con-
tinuous seal and prevent water leaks (see page
20 22\.
'14. Install the door panel (see page 20'21).
Doors
Glass/RegulatoriGlass Guide
I
,l
20-28
L-
Outer Molding Replacement
\
\
NOTEr Lower the glass Jully.
1. Remove:
. Door panel lsee page 2O-2O)
. Power mirror (see page 20 49)
2.
3.
Peel the weatherstrip away from the door lsee page
20 29), then remove the screw.
Starting at the rear, pry the outer molding up and
detach the clips, then remove the outer molding.
NOTE: Take care not to twist or scratch the outer
mold ing.
>: Clip locations, 4>: Screw locations, 2
L@
NOTE: lf necessary,replace any damagedclrps,
4. Installation is the reverse of the removal procedure.

Doors
Rear Door Index
Sedan
HINGE
*/-
6,il % TuJo^'
w<
k@
eil%
WEATHERSTRIPReplacement, page 20-39
Replacement,page 20-32
I
Replacement, page 20 38
)'--
20-30

Door
Glass/Regulator/CenterGlassGuide
Replacement (cont'd)
'12. Roll the glass up and down to see if it moves freely
without binding. Also make sure that there is no
clearance between the glass and weatherstrip when
the glass is closed. Adjust the position of the glass
as necessary (see page 20 40;.
Attach the door harness to the door correctly
page 2O-33).
Disconnect the power window switch from the
harness.
(see
14.door
When reinstalling the plastic cover, apply adhesive
along the edge where neccessary to maintain a con-
tinuous seal and prevent water leaks (see page
20 33).
16. lnstall the door panel {see page 2O-32).
Outer Molding Replacement
\NOTE: Lower the glass fully.
'1. Remove the door panel (see page 2O-32).
2. Peelthe weatherstrip away from the door (see page
2O-39i, then remove the screw.
3. Starting at the rear, pry the outer molding up and
detach the clips, then remove the outer molding.
NOTE: Take care not to twist or scratch the outer
molding.
>i Clip locations, 4 A > : Screw location, 1
>: Stabilizo. locstions, 2
.0s{0
\-
NOTEi lf necessary,replace any damagedclrps.
I ): Screw location. 1
_,f"\tjru{ 1i)
\__ -
OUTER
4. lnstallation is the reverse of the removal Drocedure.
20-38
l-
1

Doors
Glass Adjustment (cont'dl
9. Measure and record clearances "H" and "B" at the locations shown.
10. Adjust the clearance as described in steps (11) thru r4).
Measuring Points
RETAINER
"ll" Clearance'Clearance
"B" Clearsnce"B" Clearance
Section O
GLASS
Section @, Ql
RETAINEBRETAINER
20-42
"B" Clearance
"H" Clearance
socrion @
GLASSGLASS
(Standard Clearance)
a Permissible tolerance: t 0.1 mm (O.04 in)
Front: (111 and ( 121\
Rear: (13) and (141
Unit: mm iin)
Measuring
Pointo(r\\9
Clearancet-l0.8(o.03)3.O
1o.12)
10.3
(o.41)
B9.3(0.37 )
9.9
0.389
5.6
to.22l
Measuring
Point,6€)
Clearancen'to
(0.39 )
2.5
10.1)
6.O
\o.241
B5_l
to.2J
11.5(o.45)12.1
{o.48)
L---
{

12. Adjust clearance "8" as follows.
)^
d "8" {see pase 20-42}
(6
:\D \crnss
1 Lower the glass 1O mm (0.39 in).
2 Push the glass outward lO mm (0.39 in), thenpush the inside stabilizers against the glass light-
ly. Fasten the inside stabilizers.
NOTE: Check that the glass moves smoothly.
i
ilINSID€STAEILIZER
BOLT8 x 1.25 mm22 N.m 12.2 kgl.m,16 tbt ftl
3 Loosen the lo"knrt, "nd turn the adjusting bolt
until the clearance "B" is within the specilied
value.
Adiusting
Bolt
Clockwise
Top Edge
of Glass
Counter-
cloc kwise
LOCKNUT
ADJUSTING BOLT
20-44
Doors
Glass Adjustment (cont'd)
out
\
LOCKNUT
REGULATOR
ADJUSTING BOLT
NOTE: Turn the front and rear adjusting bolts the
same amount to keep the regulator parallel with the
seating sur{ace ot the door.
After tightening the adjusting bolts, make sure that
the ends of the adjusting bolts still project out of the
locknuts.
4 Align the front sash with the glass using the ad-justing bolt at the bottom of the lront sash.
5 Move the glass up and down to seat it, thenmeasure clearance "B" at the designated locations.
6 Measure clearance "H" again to make sure itis still within the specified limirs at the desig,nated locations.
NOTE: Repeat the above steps until the correct
clearances are obtained.
Top Edge
of Glass
GLASS
ADJUSTING BOLTS
I

Rear Door:
13. Adjust clearance "H" as lollows.
"H" {see page 20-42)
1 Loosen the nut securing the stopper plates.
2 Loosen the nut securing the roller guide, and
move the guide up or down to align the glass
with the body at the rear and center pillars.
GLASS
ROLLER GUIDE
LOCKNUT
3 Loosen the locknuts securing the center glass
guide, and adiust the glass Jore and aft by mov
ing the center glass gurde.
NOTE| Hold the adiLrsting bolts with a hex
wrench or flat tip screwdriver when loosening
the locknuts.
STOPPERPLATE
-4 Repeat steps 2 and 3 until clearance "H" is
within the specified limits, then fasten the center
glass guide and roller guide.
Press the stopper plates agarnst the glass stop
pers, then fasten the stopper plates.
NOTE: Check that the stopper plates contact
the glass stoppers evenlY.
STOPPEB PLATE{Front)
(cont'd )
20-45