Page 1712 of 1807
SA0QB-02
W02905
Bushing
Shock Absorber
Stabilizer
Bar Link
Adjusting Cam Washer
Lower Suspension
Arm No. 2
Brake
Caliper Drive ShaftABS Speed
Sensor
Lower Suspension
Arm No. 1
Bushing
Upper Suspension
Arm
Cotter Pin Lock Cap
Exhaust Pipe Support O-Ring Nut
Strut Rod Lower Suspension
Arm BraceAdjusting
Cam
Parking Brake Cable
Bushing
Exhaust Pipe Support Ring
Exhaust Pipe
Non-reusable part
SA-96
- SUSPENSION AND AXLEREAR UPPER SUSPENSION ARM
1786 Author: Date:
1997 SUPRA (RM502U)
REAR UPPER SUSPENSION ARM
COMPONENTS
Page 1713 of 1807
SA0QC-01
R07029
SST
R05881
- SUSPENSION AND AXLEREAR UPPER SUSPENSION ARM
SA-97
1787 Author: Date:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE DRIVE SHAFT (See page SA-51)
3. REMOVE BRAKE CALIPER
(a) Remove the 2 bolts and brake caliper from the rear axle
carrier.
Torque: 104 N´m (1,065 kgf´cm, 77 ft´lbf)
(b) Support the brake caliper securely.
4. DISCONNECT ABS SPEED SENSOR AND WIRE HAR-
NESS
(a) Remove the bolt and disconnect the speed sensor from
the axle carrier.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
(b) Disconnect the speed sensor wire harness clamp from
the upper suspension arm.
5. REMOVE UPPER SUSPENSION ARM
(a) Remove the nut from the upper suspension arm.
Torque: 108 N´m (1,100 kgf´cm, 80 ft´lbf)
(b) Using SST, disconnect the upper suspension arm from
the axle carrier.
SST 09628-6201 1
NOTICE:
Be careful not to damage the dust cover.
(c) Remove the nuts, washers, bolts and upper suspension
arm.
Torque: 164 N´m (1,670 kgf´cm, 121 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the bolt and nut.
If replacing the front nut, assemble the nut and E-ring to
the washer with lock protrusion before installing.
Page 1716 of 1807
SA0QG-02
W02905
Bushing
Shock Absorber
Stabilizer
Bar Link
Adjusting Cam Washer
Lower Suspension
Arm No. 2
Brake
Caliper Drive ShaftABS Speed
Sensor
Lower Suspension
Arm No. 1
Bushing
Upper Suspension
Arm
Cotter Pin Lock Cap
Exhaust Pipe Support O-Ring Nut
Strut Rod Lower Suspension
Arm BraceAdjusting
Cam
Parking Brake Cable
Bushing
Exhaust Pipe Support Ring
Exhaust Pipe
Non-reusable part
- SUSPENSION AND AXLEREAR LOWER SUSPENSION ARM AND STRUT ROD
SA-101
1791 Author: Date:
1997 SUPRA (RM502U)
REAR LOWER SUSPENSION ARM AND STRUT ROD
COMPONENTS
Page 1717 of 1807
SA0QH-01
R07312
R07045
SST
R07038
Matchmarks SA-102
- SUSPENSION AND AXLEREAR LOWER SUSPENSION ARM AND STRUT ROD
1792 Author: Date:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE REAR DRIVE SHAFT (See page SA-51)
3. REMOVE BRAKE CALIPER
(a) Remove the 2 bolts and brake caliper from the rear axle
carrier.
Torque: 104 N´m (1,065 kgf´cm, 77 ft´lbf)
(b) Support the brake caliper securely.
4. REMOVE STRUT ROD
Remove the 2 nuts, washer, bolts and strut rod.
Torque: 184 N´m (1,880 kgf´cm, 136 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the bolts.
5. REMOVE LOWER SUSPENSION ARM NO.1
(a) Remove the nut.
Torque: 59 N´m (600 kgf´cm, 43 ft´lbf)
(b) Using SST, disconnect the lower suspension arm No.1
from the rear axle carrier.
SST 09610-20012
NOTICE:
Be careful not to damage the dust boot.
(c) Remove the bolt and disconnect the parking brake cable
bracket.
Torque: 19 N´m (190 kgf´cm, 14 ft´lbf)
(d) Place matchmarks on the adjusting cam No.1 and sub-
frame.
(e) Remove the nut, washer, adjusting cam plate No.1 and
adjusting cam No.1.
Torque: 184 N´m (1,880 kgf´cm, 136 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nut.
(f) Remove the lower suspension arm No.1.
Page 1769 of 1807
SS0DE-02
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS-57
214 Author: Date:
1997 SUPRA (RM502U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Front
Hub nut1031,05076
Lower suspension arm x Suspension crossmember2262,300166
Lower suspension arm bracket stay Bolt
Nut44
59450
60032
43
Tie rod end lock nut5657041
Axle hub lock nut1992,030147
Upper suspension arm x Sub-frame1641,670121
Lower suspension arm x Shock absorber bracket5253038
Tie rod end x Steering knuckle4950036
Steering knuckle x Upper suspension arm1031,05076
Steering knuckle x Lower suspension arm1251,27092
Brake caliper x Steering knuckle11 81,20087
ABS speed sensor x Steering knuckle7.88069 in.´lbf
Upper suspension arm x ABS speed sensor wire harness clamp5.45548 in.´lbf
Front shock absorber x Body3536026
Front shock absorber x Lower suspension arm1431,460106
Front shock absorber x Suspension support2930022
Stabilizer bar link x Shock absorber bracket7475054
Stabilizer bar link x Stabilizer bar7475054
Stabilizer bar bracket x Body1818013
Steering knuckle x Brake dust cover8.08574 in.´lbf
Page 1770 of 1807
SS-58
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
215 Author: Date:
1997 SUPRA (RM502U)Part tightened
N´mkgf´cmft´lbf
Rear
Hub nut1031,05076
Rear shock absorber x Lower suspension arm No.21371,400101
Upper suspension arm x Suspension crossmember1641,670121
Rear axle carrier x Brake caliper1041,06577
Lower suspension arm No.1 x Rear axle carrier5960043
Lower suspension arm No.1 x Subframe1841,880136
Lower suspension arm No.2 x Rear axle carrier1501,52511 0
Lower suspension arm No.2 x suspension crossmember1841,880136
Lower suspension arm brace x Subframe1818013
ABS speed sensor x Rear axle carrier7.88069 in.´lbf
Parking brake cable set bolt8.08069 in.´lbf
Strut rod x Rear axle carrier1841,880136
Strut rod x Body1841,880136
Rear drive shaft x Axle hub2892,950213
Upper suspension arm x Rear axle carrier1081,10080
Backing plate x Rear axle carrier2626019
Shoe guide plate set bolt1818513
Parking brake cable clamp set bolt1919014
Rear axle carrier x Backing plate Hexagon bolt1801,825132
Rear drive shaft x Differential 2JZ-GE
2JZ-GTE65
83660
85048
61
Heat insulator set nut5.45548 in.´lbf
Center floor crossmember brace set nut131309
Center support bearing set bolt4950036
Rear differential x Propeller shaft7980558
Propeller shaft x Transmission 2JZ-GTE5657041
Oxygen sensor 2JZ-GE4445034
Front exhaust pipe x Center exhaust pipe 2JZ-GE
2JZ-GTE44
58450
59033
43
Oxygen sensor set nut 2JZ-GTE2020014
Differential mounting boltFront
Rear147
1421,500
1,450108
105
Ring gear x Differential caseSee page SA-74
Drive pinion x Companion flange2JZ-GTE M/T (Maximam)
Except 2JZ-GTE M/T (Maximam)510
4905,200
5,000376
362
Differential carrier retainer set bolt 2JZ-GTE M/T
Except 2JZ-GTE M/T47
22480
22535
16
Differential carrier cover set bolt 2JZ-GTE M/T
Except 2JZ-GTE M/T78
47800
47558
34
Differential carrier cover x Deflector7.07062 in.´lbf
Drain and Filler plug4950036
Breather plug2121015
Shock absorber x Body2626019
Shock absorber cape x Suspension support101058
Suspension support x Shock absorber2728020
Page 1772 of 1807
SS0D3-01
SS-60
- SERVICE SPECIFICATIONSBRAKE
217 Author: Date:
1997 SUPRA (RM502U)
BRAKE
SERVICE DATA
Brake pedal height from asphalt sheet154.2 - 164.2 mm (6.071 - 6.465 in.)
Brake pedal freeplay1 - 6 mm (0.04 - 0.24 in.)
Brake pedal reserve distance at 490 N (50 kgf, 110.2 lbf)
2JZ-GTE Engine
2JZ-GE Engine
More than 70 mm (2.76 in.)
More than 72 mm (2.83 in.)
Brake booster push rod to piston clearance (w/ SST)0 mm (0 in.)
Front brake pad thickness (2JZ-GTE Engine) STD12.0 mm (0.472 in.)
Front brake pad thickness (2JZ-GTE Engine) Minimum1.0 mm (0.039 in.)
Front brake pad thickness (2JZ-GE Engine) STD11.0 mm (0.433 in.)
Front brake pad thickness (2JZ-GE Engine) Minimum1.0 mm (0.039 in.)
Front brake disc thickness (2JZ-GTE Engine) STD30.0 mm (1.181 in.)
Front brake disc thickness (2JZ-GTE Engine) Minimum28.0 mm (1.102 in.)
Front brake disc thickness (2JZ-GE Engine) STD32.0 mm (1.260 in.)
Front brake disc thickness (2JZ-GE Engine) Minimum30.0 mm (1.181 in.)
Front brake disc runout Maximum0.05 mm (0.0020 in.)
Rear brake disc pad thickness (2JZ-GTE Engine) STD11.0 mm (0.433 in.)
Rear brake disc pad thickness (2JZ-GTE Engine) Minimum1.0 mm (0.039 in.)
Rear brake disc pad thickness (2JZ-GE Engine) STD10.0 mm (0.394 in.)
Rear brake disc pad thickness (2JZ-GE Engine) Minimum1.0 mm (0.039 in.)
Rear brake disc thickness STD16.0 mm (0.630 in.)
Rear brake disc thickness Minimum15.0 mm (0.591 in.)
Rear brake disc runout Maximum0.05 mm (0.0020 in.)
Rear brake disc inside diameter STD190 mm (7.48 in.)
Rear brake disc inside diameter Maximum191 mm (7.52 in.)
Parking brake lining thickness STD2.5 mm (0.098 in.)
Parking brake lining thickness Minimum1.0 mm (0.039 in.)
Parking brake lever travel at 196 N (20 kgf, 44.1 lbf)5 - 8 clicks
Parking brake clearance between rear shoe and leverLess than 0.35 mm (0.0138 in.)
Parking brake adjusting shim thickness for rear disc brake
0.3 mm (0.012 in.)
0.6 mm (0.024 in.)
0.9 mm (0.035 in.)
Page 1773 of 1807
SS0D4-01
- SERVICE SPECIFICATIONSBRAKE
SS-61
218 Author: Date:
1997 SUPRA (RM502U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Master cylinder x Piston stopper bolts101007
Master cylinder x Reservoir1.81816 in.´lbf
Master cylinder x Brake booster131309
Brake line union nut1515511
Brake booster clevis lock nut2526019
Brake booster x Pedal bracket131309
Bleeder plug1111 08
Front disc brake caliper x Steering knuckle 2JZ-GTE Engine11 81,20087
Front disc brake torque plate x Steering knuckle 2JZ-GE Engine11 81,20087
Front disc brake caliper installation bolt 2JZ-GE Engine3435025
Front disc brake caliper x Flexible hose union bolt3031022
Rear disc brake caliper x Axle carrier 2JZ-GTE Engine1041,06577
Rear disc brake torque plate x Axle carrier 2JZ-GE Engine1041,06577
Rear disc brake caliper installation bolt 2JZ-GE Engine3435025
Rear disc brake caliper x Flexible hose union bolt3031022
ABS actuator x ABS actuator bracket5.45548 in.´lbf
ABS actuator assembly x Body1919514
Cruise control actuator x Body1919514
Cruise control actuator x ABS actuator x Body1919514
Front speed sensor installation bolt7.88069 in.´lbf
Front speed sensor harness set bolt5.45548 in.´lbf
Rear speed sensor installation bolt7.88069 in.´lbf
Rear speed sensor harness set nut5.45548 in.´lbf
