1997 SSANGYONG KORANDO head gasket

OM600 ENGINE MECHANICAL 1B3 -- 155
D AEW OO M Y_2000
In this position, the marking on the camshaft / cam-
shaft bearing cap (arrow) must also be aligned.
5. Install the guide pulley (12).
Tightening Torque23 N∙m (17 lb-ft)
6. Attach the tensioning lever (7) to the spring (15) and
install.
7. Replace the gasket and install the cylinder head
cover.
Tightening Torque10 N∙m(89lb-in)

OM600 ENGINE MECHANICAL 1B3 -- 177
D AEW OO M Y_2000
UNIT REPAIR
CYLINDER HEAD PRESSURE LEAKAGE TEST
Preceding Work : Removal of the cylinder head
Removal of the exhaust manifold
Removal of the valve
1 Feed Pipe
2Bolt
3 Return Connection
4 Gasket Replace.................................
5 Coolant Gallery Sealing..........................
6 Pressure Measuring Plate Completely tight to the cylinder head.................
7 Cylinder Head...........................
Immerse with pressure measuring plate into warm water of approx. 60_C and pressurize with compressed
air of 2 bar.
Notice
If air bubbles are seen, replace the cylinder head.
Tools Required
115 589 34 63 00 Pressure Measuring Plate
601 589 00 25 00 Suspension Device

OM600 ENGINE CONTROLS 1F3 -- 29
D AEW OO M Y_2000
REMOVAL AND INSTALLATION OF INJECTION TIMING DEVICE
Preceding Work : Removal of vacuum pump
1 Cylinder Head Cover
2 Bolt 10N∙m (89 lb-in) .....................
3 Gasket Replace..........................
4 Fuel Injection Pump
5 Seal Replace.............................
6 Screw Plug 30N∙m (22 lb-ft) ................
7OilPan
8 Locking Pin
9 Injection Timing Device10 Washer
11 Bolt (Left -- Hand Thread) 46N∙m (34 lb-ft) ....
12 Camshaft Sprocket
13 Washer
14 12-- Sided Stretch Bolt
Check, 25N∙m (18 lb-ft) +90_ ..............
15 Timing Chain
16 Seal
17 Chain Tensioner 80N∙m (59 lb-ft) ............

1F3 -- 30 OM600 ENGINE CONTROLS
D AEW OO M Y_2000
Tools Required
601589000800 Flange
601 589 05 21 00 Locking Screw
116 589 20 33 00 Sliding Hammer
116 589 02 34 00 Threaded Bolt
667 589 04 63 00 Retaining Plate
Removal & Installation Procedure
1. Remove the bolts (2) and then remove the cylinder
head cover (1) and gasket (3).
Installation Notice
Tightening Torque10 N∙m(89lb-in)
Notice
Replace the gasket.
Rotate the engine 1 revolution by hand and check
TDC marking of the crankshaft and camshaft.
2. Loosen the camshaft sprocket bolt (14).
Notice
Do not remove the bolt.
Installation Notice
Tightening Torque25N∙m (18 lb-ft) + 90_
Notice
If max. length of bolt exceeds 53.6mm, replace it.
3. Loosen the bolt (11) (left -- hand thread).
Notice
Do not remove the bolt.

5A-168 AUTOMATIC TRANSMISSION
SSANGYONG MY2002
Pump
Notice: The following valves are housed in the pump
cover:
Solenoid 7
Converter clutch control valve
Converter clutch regulator valve
Primary regulator valve
1. Remove the wiring loom retainer plate and remove
solenoid 7 with a T30 Torx bit.
2. Remove the five washer head bolts from the cover
plate using a multi-point 8 mm socket.
3. Remove the five Torx head screws from the cover
plate with T30 Torx bit. Note that the long screw
holds the pump body to the pump body cover.
Notice: Do not strike the converter support tube to
loosen the pump body.
4. Separate the pump body from the pump cover.
5. Remove the cover plate, gasket and seal from the
cover.
6. Remove the ball check valve and one spring from
the pump cover.
KAA5A790 KAA5A780 KAA5A770