1997 MAZDA MX-5 Factory Repair Manual

5. Check continuity between terminal No. Q and ground. If continuity exists, replace or repair wiring
harness between instrument cluster and SAS unit. If no continuity exists, replace SAS unit. See SAS
UNIT under REMOVAL & INSTALLATION.
6. Activate air bag system and perform SYSTEM OPERATION CHECK
. Check that AIR BAG warning
light is operating properly. If not, reconfirm malfunction symptoms.
DTC 0 - SAS UNIT
1. Disable system. See DISABLING & ACTIVATING AIR BAG SYSTEM
. Remove dashboard.
Remove heater unit. Check if SAS unit connector is securely connected. If not, reconnect connector and
go next step. If ok, go to next step.
2. Disconnect SAS unit connector and check for continuity between terminal No. V and terminal No. Y of
SAS unit connector. If there is continuity, replace SAS unit. If there is no continuity, replace wiring
harness. Perform SYSTEM OPERATION CHECK
.
DTC 3 - BATTERY
1. Check that battery voltage is at least 8 volts. If not, check battery and/or charging system. Turn ignition
on and check voltage at joint connector terminals A or E (X-33).
2. If voltage is over 8 volts, replace SAS unit. See SAS UNIT
under REMOVAL & INSTALLATION. If
voltage is not over 8 volts, replace wiring harness from battery to fuse box. Perform SYSTEM
OPERATION CHECK .
DTC 6 - DRIVER-SIDE AIR BAG MODULE
1. Disable air ba
g system. See procedures under DISABLING & ACTIVATING AIR BAG SYSTEM. NOTE: When air bag warning light remains on, it can indicate a DTC 0 caused by no
continuity between terminal No. V and terminal No. Y of SAS unit This can be
due to a damaged SAS unit, an open or short circuit in wiring harness or poor
connections.
NOTE: For connector terminal identification, see WIRING DIAGRAM
.
NOTE: When voltage supplied to SAS unit is less than 1 volt due to weak battery, open
or short in wiring harness, poor connection of connector or damaged SAS unit,
DTC 3 will set
NOTE: For connector terminal identification, see WIRING DIAGRAM
.
NOTE: When resistance Is detected between terminals M-O of SAS unit is NOT 2 ohms,
DTC 6 will set.
NOTE: For connector terminal identification, see WIRING DIAGRAM
.

1997 Mazda MX-5 Miata
AIR BAG RESTRAINT SYSTEM 1997 ACCESSORIES/SAFETY EQUIPMENT Mazda - Air Bag Restraint System
Microsoft
Sunday, July 05, 2009 1:40:48 PMPage 17 © 2005 Mitchell Repair Information Company, LLC.

Remove driver-side air bag module. See DRIVER-SIDE AIR BAG MODULE under REMOVAL &
INSTALLATION.
2. Inspect clockspring connectors for damage. If connectors are okay, go to next step. If connectors are
damaged, replace clockspring. Perform SYSTEM OPERATION CHECK
.
3. Connect Special Service Tool (49 0839 285) to terminal No. 3B and terminal No. 3C of clockspring. Set
SST resistance to 2 ohms. Connect clockspring connector. Connect negative battery cable. Turn ignition
switch to ON position and cheek for codes. If CODE 6 is displayed, go to next step. If CODE 6 is not
present, replace driver-side air bag module. Perform SYSTEM OPERATION CHECK
.
4. Turn ignition switch to LOCK position. Disconnect negative battery cable and wait for 1 minute.
Disconnect clockspring connector and inspect. If pins are ok go next step. If pins are damaged, replace
wiring harness from clockspring to SAS unit.
5. Connect Special Service Tool (49 0839 285) to terminal No. A and terminal No. B of clockspring
connector. Set SST resistance to 2 ohms. Connect clockspring connector and connect negative battery
cable. Turn ignition switch to ON position and cheek for codes. If CODE 6 is displayed, go to next step.
If CODE 6 is not present, replace clockspring. See CLOCKSPRING
under REMOVAL &
INSTALLATION. Perform SYSTEM OPERATION CHECK
.
6. Turn ignition switch to LOCK position. Disconnect negative battery cable. Wait for 1 minute. Remove
dashboard and heater unit. Disconnect SAS unit connector.
7. Check wiring harness between terminal No. O of SAS unit connector and between terminal No. A of
clockspring connector. Also check between terminal No. M of SAS unit connector and terminal No. B of
clockspring connector. Check for short to ground, short to power or open circuit. If wiring is OK, replace
SAS unit. See SAS UNIT
under REMOVAL & INSTALLATION.If wiring is not OK, replace wiring
harness from clockspring to SAS unit. Perform SYSTEM OPERATION CHECK
.
DTC 7 - PASSENGER-SIDE AIR BAG MODULE
1. Disable air bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM
. Inspect passenger-
side air bag module connectors for damage. If connectors are okay, go to next step. If connectors are
damaged, replace wiring harness from passenger-side air bag module to SAS unit. Perform SYSTEM
OPERATION CHECK .
2. Connect Special Service Tool (49 0839 285) to terminal No A and terminal No. B of passenger-side air
bag module connector. Set Special Service Tool resistance to 2 ohms. Connect clockspring connector.
Connect negative battery cable. Turn ignition switch to ON position and check for codes. If DTC 7 is
displayed, go to next step. If CODE 7 is not present replace passenger-side air bag module. See
PASSENGER
-SIDE AIR BAG MODULE under REMOVAL & INSTALLATION. Perform SYSTEM
OPERATION CHECK .
3. Turn ignition switch to LOCK position. Disconnect negative battery cable and wait 1 minute. Disconnect
clocksprin
g connector. Remove dashboard and heater unit. NOTE: For connector terminal identification, see WIRING DIAGRAM
.
NOTE: When resistance is detected between terminals l-K of SAS unit is NOT 2 ohms
and/or there is no continuity between terminal No. E of SAS unit and ground,
DTC 7 will set

1997 Mazda MX-5 Miata
AIR BAG RESTRAINT SYSTEM 1997 ACCESSORIES/SAFETY EQUIPMENT Mazda - Air Bag Restraint System
Microsoft
Sunday, July 05, 2009 1:40:48 PMPage 18 © 2005 Mitchell Repair Information Company, LLC.

4. Disconnect SAS unit connector. Check wiring between terminal K of SAS unit connector and terminal C
of passenger-side air bag module connector for short to ground, short to power or open circuit. If wiring
is OK, replace SAS unit. See SAS UNIT
under REMOVAL & INSTALLATION. If wiring is not OK,
replace wiring harness between passenger-side air bag module and SAS unit. Perform SYSTEM
OPERATION CHECK .
WIRE REPAIR
DO NOT repair air bag system wiring. If a problem is found with air bag system wiring, replace faulty wiring.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS
WIRING DIAGRAM
ApplicationFt. Lbs. (N.m)
Passenger-Side Air Bag Module Retaining Bolts13-20 (18-27)
Steering Wheel Nut29-36 (39-49)
INCH Lbs. (N.m)
Driver-Side Air Bag Module Retaining Nuts35-52 (4.0-5.8)
SAS Unit Retaining Nuts61-86 (6.7-9.8)

1997 Mazda MX-5 Miata
AIR BAG RESTRAINT SYSTEM 1997 ACCESSORIES/SAFETY EQUIPMENT Mazda - Air Bag Restraint System
Microsoft
Sunday, July 05, 2009 1:40:48 PMPage 19 © 2005 Mitchell Repair Information Company, LLC.

1997 Mazda MX-5 Miata
AIR BAG RESTRAINT SYSTEM 1997 ACCESSORIES/SAFETY EQUIPMENT Mazda - Air Bag Restraint System
Microsoft
Sunday, July 05, 2009 1:40:48 PMPage 20 © 2005 Mitchell Repair Information Company, LLC.

Fig. 10: SRS Wiring Diagram

1997 Mazda MX-5 Miata
AIR BAG RESTRAINT SYSTEM 1997 ACCESSORIES/SAFETY EQUIPMENT Mazda - Air Bag Restraint System
Microsoft
Sunday, July 05, 2009 1:40:48 PMPage 21 © 2005 Mitchell Repair Information Company, LLC.

ANTI-LOCK BRAKE SYSTEM
1997 BRAKES Mazda - Anti-Lock
DESCRIPTION
The Anti-Lock Brake System (ABS) control module senses reductions in front and rear wheel speed and
modulates hydraulic pressure to the brakes to prevent wheel lock-up. The ABS consists of a hydraulic unit, 4
wheel speed sensors and sensor rotors, valve relay, motor relay, pump motor and ABS control module. An ABS
warning light is located on the instrument cluster.
OPERATION
Under normal driving conditions, Anti-Lock Brake System (ABS) functions like a standard brake system. When
vehicle speed reaches 3.8 MPH, ABS will diagnose pump motor by briefly operating motor. Pump motor
operation may be heard inside vehicle.
ABS control module controls ABS by detecting speed sensor signals and activating solenoid valve in hydraulic
unit. Control module also controls pump motor and self-diagnostic function. If a problem is detected in ABS,
ABS will function like a conventional brake system. ABS warning light will also come on.
With detection of wheel lock-up, short pedal pulsations, occurring in rapid succession, will be felt in brake
pedal and steering wheel. Vehicle body may also vibrate slightly. These conditions are normal. Pedal pulsation
will continue until there is no longer a need for anti-lock function or until vehicle is stopped.
COMPONENT LOCATIONS
COMPONENT LOCATIONS CAUTION: See ANTI
-LOCK BRAKE SAFETY PRECAUTIONS article in GENERAL
INFORMATION.
NOTE: For more information on brake system, see BRAKE SYSTEM article.
ApplicationLocation
ABS Control ModuleUnder Carpet, Behind Passenger Seat
Data Link ConnectorLeft Side Of Engine Compartment
Front Sensor RotorOn Front Wheel Hub
Hydraulic UnitRight Rear Of Engine Compartment
Motor & Valve RelaysOn Hydraulic Unit
Pump MotorOn Hydraulic Unit
Rear Sensor RotorOn Rear Drive Axle
Wheel Speed SensorOn Knuckle

1997 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1997 BRAKES Mazda - Anti-Lock

1997 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1997 BRAKES Mazda - Anti-Lock
Microsoft
Sunday, July 05, 2009 1:48:48 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.
Microsoft
Sunday, July 05, 2009 1:48:54 PMPage 1 © 2005 Mitchell Repair Information Company, LLC.

BLEEDING BRAKE SYSTEM
1. Raise and support vehicle. Ensure brake fluid reservoir remains at least half full during bleeding
procedure. When bleeding brake system, start with longest brakeline first. Remove bleed screw cap.
Connect one end of transparent vinyl tube to bleed screw. Submerge other end of tube in a container half
filled with clean brake fluid.
2. Have an assistant depress brake pedal several times and hold in depressed position. Loosen bleed screw
and drain fluid into container. Tighten bleed screw.
3. Refill brake fluid reservoir if necessary. Repeat step 2) until air is no longer discharged. Tighten bleed
screw to 52-78 INCH lbs. (5.9-8.8 N.m). Ensure fluid leakage is not present. Add fluid to reservoir.
Repeat procedure for remaining wheels.
TROUBLE SHOOTING
Before attempting to diagnose vehicle, ensure ABS warning light is functioning properly. ABS warning light
will not illuminate and ABS will not operate if battery voltage is insufficient. Perform trouble shooting
procedures on ABS warning light to eliminate unnecessary repairs and/or component replacement.
ABS WARNING LIGHT DOES NOT ILLUMINATE WHEN IGNITION IS TURNED ON
1. Turn ignition on. Check if other warning lights illuminate. If other warning lights do not illuminate, check
METER fuse. Replace as necessary. If other warning lights illuminate, check for possible malfunction
and repair as necessary. Go to next step.
2. Turn ignition off. Disconnect ABS Control Module (ABS CM) connector. See COMPONENT
LOCATIONS . Turn ignition on. Check if ABS warning light illuminates. If ABS warning light
illuminates, go to next step. If ABS warning light does not illuminate, go to step 5).
3. Reconnect ABS CM connector. Turn ignition on. Check if ABS warning light illuminates. If ABS
warning light does not illuminate, go to next step. If ABS warning light illuminates, a temporary poor
contact in wiring may have occurred and ABS is now functioning properly.
4. Check if terminal AD of ABS CM harness connector is damaged or deformed. See Fig. 3
. If terminal AD
is damaged or deformed, replace wiring harness connector. If terminal AD is okay, replace ABS CM.
5. With ABS CM connector disconnected, use a jumper wire and ground terminal AD of ABS CM harness
connector. Check if ABS warning light illuminates. If ABS warning light illuminates, go to next step. If
ABS warning light does not illuminate, go to step 7).
6. With ABS CM disconnected, check continuity between terminal AB of ABS CM harness connector and
ground. Also, check continuity between terminal AC of ABS CM harness connector and ground, and CAUTION: DO NOT allow reservoir to run dry during brake bleeding procedure. If
brake fluid is spilled, clean surface immediately with alcohol, as brake
fluid will damage painted surfaces. Use only DOT 3 brake fluid and DO
NOT mix with any other types.
NOTE: Ensure brake pedal remains depressed until bleed screw is tightened.

1997 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1997 BRAKES Mazda - Anti-Lock
Microsoft
Sunday, July 05, 2009 1:48:48 PMPage 2 © 2005 Mitchell Repair Information Company, LLC.

between terminal AM of ABS CM harness connector and ground. If continuity exists, replace wiring
harness connector. If continuity does not exist, repair wiring harness.
7. Check ABS warning light bulb. Replace bulb as necessary. If bulb is okay, go to next step.
8. Check continuity between terminal AD of ABS CM harness connector and terminal 1K of instrument
cluster connector. See WIRING DIAGRAMS
. If continuity exists, check ABS warning light. See ABS
WARNING LIGHT under COMPONENT TESTING
. If continuity does not exist, repair wiring
harness.
ABS WARNING LIGHT REMAINS ILLUMINATED
1. Ensure battery is fully charged. Charge or replace as necessary. If battery is fully charged, go to next step.
2. Check ABS Control Module (ABS CM) connector for poor connection. Turn ignition on. Check if ABS
warning light goes out. If ABS warning light does not go out, go to next step. If ABS warning light goes
out, a temporary poor contact in wiring may have occurred and ABS is now functioning properly.
3. Turn ignition off. Disconnect ABS CM connector. See COMPONENT LOCATIONS
. Measure voltage
between terminals "A" and AB of ABS CM harness connector. See Fig. 3
. Also, measure voltage
between terminals "A" and AC of ABS CM harness connector, and between terminals "A" and AM of
ABS CM harness connector. If battery voltage is present, go to next step. If battery voltage is not present,
repair wiring harness.
4. Connect ABS CM connector. Check for ABS DTCs. See RETRIEVING DIAGNOSTIC TROUBLE
CODES under DIAGNOSIS & TESTING. If no DTCs are present, go to next step.
5. Turn ignition off. Disconnect ABS CM connector. Connect Harness Adapter (49-F066-022). Turn
ignition on. Check if ABS warning light goes out. If ABS warning light does not go out, repair short in
ABS warning light drive harness or instrument cluster. If ABS warning light goes out, replace ABS CM.
ABS WARNING LIGHT FLASHES WITH VEHICLE STOPPED
1. Ensure battery is fully charged. Charge or replace as necessary. If battery is fully charged, go to next step.
2. Check if a jumper wire is installed between terminals TBS and GND of Data Link Connector (DLC). See
Fig. 1
. If jumper wire is installed, remove jumper wire from DLC. If jumper wire is not installed, go to
next step.
3. Turn ignition off. Disconnect ABS Control Module (ABS CM) connector. See COMPONENT
LOCATIONS . Check continuity between terminal "P" of ABS CM harness connector and ground. See
Fig. 3
. If continuity exists, repair short to ground in DLC wiring harness. If continuity does not exist,
replace ABS CM. NOTE: ABS warning light will illuminate if voltage between terminal "A" (voltage
supply) of ABS CM harness connector and ground is less than about 10
volts.

1997 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1997 BRAKES Mazda - Anti-Lock
Microsoft
Sunday, July 05, 2009 1:48:48 PMPage 3 © 2005 Mitchell Repair Information Company, LLC.