1997 LINCOLN TOWN CAR Owners Manual

199
6. Lower the vehicle by turning the jack handle
counterclockwise.
7. Remove the jack and fully tighten the lug nuts
in the order shown in the following illustration.
As soon as possible, have your dealer or a
qualified service technician check the lug nuts
for proper torque specifications.
The lug nuts on the wheel
8. Place any ornaments in the trunk.
9. Put the tire, jack, and wrench away. Make sure
the jack is securely fastened so it does not
rattle when you drive.
10. Unblock the wheels.
11. Turn on the air suspension switch.
After replacing a flat tire with the temporary spare
tire, the flat tire can be secured in the trunk tub by
placing the ªJº hook through a lug nut hole in the
wheel with the tire and wheel lying at an angle.Installation of the black dust shield.When installing the regular tire, reinstall the black
dust shield by orienting and sliding the shield until
it is flush with the hub/rotor assembly.
File:10fnert.ex
Update:Thu Jun 20 15:16:36 1996

200Aluminum wheelLacy spoke aluminum wheel
Remove the center ornament from the wheel with
the tapered end of the wheel nut wrench by
inserting the end under one of two raised notches,
and rotate the handle while prying against the
wheel.
Install the center ornament on the wheel and be
sure it is snapped into place all the way around
using the palm of the hand or a rubber mallet.
File:10fnert.ex
Update:Thu Jun 20 15:16:36 1996

201
Y-spoke aluminum wheelY-spoke aluminum wheel
Remove the center ornament from the wheel with
the tapered end of the wheel nut wrench by
inserting the end into the notch and, rotate the
handle while prying against the wheel.
Install the center ornament on the wheel and be
sure it is snapped into place all the way around
using the palm of the hand or a rubber mallet.
File:10fnert.ex
Update:Thu Jun 20 15:16:36 1996

202Steel wheel with full wheelcoverSteel wheel with full wheelcover
Remove the wheelcover from the wheel using the
flanged end of the wheel nut wrench by inserting
the handle and then prying against the inner
wheelcover flange.
Install the wheelcover on the wheel with the valve
stem in the wheel matching the hole in the
wheelcover. Push by hand on the outside edges of
the wheelcover until it is snapped firmly in place on
the wheel.
NOTE:DO NOT USE A STEEL HAMMER.
If you have the anti-theft locking spoked wheel
cover, each wheel cover has a lock bolt behind the
center hub ornament. You need a special key
wrench (stored in the glove box) to pry this
ornament off and to remove the lock bolt. Do not
lose this wrench or you will not be able to remove
the wheel cover.
File:10fnert.ex
Update:Thu Jun 20 15:16:36 1996

203
The key wrench has a registration number attached
to it. Keep the registration number in a safe place.
Complete the registration card and return it to the
manufacturer as soon as you buy the vehicle. To
replace the key wrench, send the I.D. card to the
manufacturer.Anti-Theft Wheel Lug Nuts
(If equipped)If your vehicle has this option, one of the lug nuts
on each wheel locks and must be unlocked with a
special key. The key and registration card are
attached to the lug wrench and stored with the
spare tire. If you lose the key, send the registration
card to the manufacturer (not the dealer) to get a
replacement key.
NOTE:If entire lug wrench/lug nut key assembly
is lost, see your nearest Ford or Lincoln-Mercury
dealer who has access to a master set of keys.
NOTE:DO NOT USE A POWER IMPACT
WRENCH ON THE LUG NUT KEY.The anti-theft lug nut and key
Removing the anti-theft lug nutInsert the key over the locking lug nut. Make sure
that you hold the key square to the lug nut. If you
hold the key on an angle, you may damage the key
and the lug nut.
Place the lug nut wrench over the lug nut key and
apply pressure on the key with the wrench. Turn
the wrench in a counterclockwise direction to
remove the lug nut.
File:10fnert.ex
Update:Thu Jun 20 15:16:36 1996

204
Reinstallingth eanti-thef tlu g nut
WARNING
Th egase saroun dthebatter ycan
W ARNING
To protec tyoursel fwhe nchargin ga
WARNING
Applyin gtoo muc hpressur eon the
WARNING
Batterie scontai nsulfuri caci dwhich

205
If the acid touches someone's skin, eyes, or
clothing, immediately flush the area with water for
at least 15 minutes. If someone swallows the acid,
have him or her drink lots of milk or water first,
then Milk of Magnesia, a beaten egg, or vegetable
oil. Call a doctor immediately.
To avoid damaging your vehicle or your battery,
and to avoid injury to yourself, follow these
directions for preparing your vehicle to jump-start
and connecting the jumper cables in the order they
are given. If in doubt, call for road service.Preparing Your Vehicle1. Your vehicle has a 12-volt starting system, so
you need to use a 12-volt jumper system. You
will damage your starting motor, ignition
system, and other electrical parts if you connect
them to a 24-volt power supply (either two
12-volt batteries in series or a 24-volt generator
set).2. Do not disconnect the battery of the disabled
vehicle. You could damage the vehicle's
electrical system.
3. Park the booster vehicle close to the hood of
the disabled vehicle.Make sure the vehicles
do not touch each other.Set the parking
brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
4. Check all battery terminals and remove any
excessive corrosion before you attach the
jumper cables.
5. Turn on the heater fan in both vehicles. Press
the DEFROST button. Turn off all other
switches and gauges.
File:10fnert.ex
Update:Thu Jun 20 15:16:36 1996

206
Connectingth e jumpe rcablesWARNING
D o no tconnec tth een dof th esecond