SS0LL-04
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A132L)
SS-29
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Oil pan drain plug4950036
Oil pan4.95043 in.´lbf
Detent spring101007
Valve body x Oil pipe clamp101007
Valve body x Oil strainer101007
Valve body x Apply pipe bracket101007
Valve body x Transaxle101007
Park/neutral position switch x Transaxle case (bolt)5.45548 in.´lbf
Park/neutral position switch (nut)6.97061 in.´lbf
Transaxle control shaft lever x Park/neutral position switch131309
Transaxle control shaft lever x Transaxle control cable121209
Drive plate x Crankshaft8890065
Torque converter clutch x Drive plate2728020
Starter3940029
Transaxle housing x Engine (upper side)6465047
Transaxle housing x Engine (lower side) Bolt A
Bolt B
Bolt C
Bolt D7.4
25
46
6475
250
470
65065 in.´lbf
18
34
47
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Oxygen sensor4445032
Exhaust pipe clamp1919014
LH engine mounting x Body4949036
Engine rear mounting bracket x Engine rear mounting insulator6565048
Engine rear mounting insulator x Body Bolt A
Bolt B80
92800
92059
69
SS0LJ-04
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A242L)
SS-31
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Oil pan drain plug1717513
Oil pan4.95043 in.´lbf
Detent spring101007
Valve body x Oil pipe clamp101007
Valve body x Oil strainer101007
Valve body x Apply pipe bracket101007
Valve body x Transaxle101007
Park/neutral position switch x Transaxle case (bolt)5.45548 in.´lbf
Park/neutral position switch (nut)6.97061 in.´lbf
Transaxle control shaft lever x Park/neutral position switch131309
Transaxle control shaft lever x Transaxle control cable121209
Drive plate x Crankshaft8890065
Torque converter clutch x Drive plate2728020
Starter3940029
Transaxle housing x Engine (upper side)6465047
Transaxle housing x Engine (lower side) Bolt A
Bolt B
Bolt C7.4
64
4675
650
47065 in.´lbf
47
34
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Oxygen sensor4445032
Exhaust pipe clamp1919014
LH engine mounting x Body4949036
Engine rear mounting bracket x Engine rear mounting insulator6565048
Engine rear mounting insulator x Body Bolt A
Bolt B80
92800
92059
69
Z14807
Oil Pump
Oil PanFIPG
A' - A
Front
Seal Diameter
a: 7mm
b: 4mm
c: 5mmB' - B C' - C ab
bc
B'
BC'
C
- LUBRICATIONOIL PUMP
LU-15
1996 TERCEL (RM440U)
Parts must be assembled within 5 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.
Immediately remove nozzle from the tube and rein-
stall cap.
(f) Place a new O-ring into the cylinder block side groove.
(g) Install the oil pump and tension spring bracket with the 9
bolts.
Torque: 7.5 N´m (75 kgf´cm, 65 in.´lbf)
2. INSTALL PRESSURE REGULATOR VALVE
Torque: 30 N´m (300 kgf´cm, 22 ft´lbf)
3. INSTALL OIL STRAINER
(a) Apply a little engine oil to a new O-ring.
(b) Install the O-ring to the oil strainer.
(c) Install the oil strainer with the 3 bolts.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
4. INSTALL OIL PAN
(a) Remove any old packing (FIPG) material and be careful
not to drop any oil on the contact surfaces of the oil pan,
oil pump, rear oil seal retainer and cylinder block.
Using a razor blade and gasket scraper, remove all
the packing (FIPG) material from the contact sur-
faces.
Thoroughly clean all components to remove all the
loose material.
Using a non-residue solvent, clean both sealing
surfaces.
NOTICE:
Do not use a solvent which will affect the painted surfaces.
(b) Apply seal packing to the oil pump, rear oil seal retainer
and oil pan as shown in the illustration.
Seal packing:
Part No. 08826-00080 or equivalent
Seal diameter:
7 mm ( 0.28 in.) for a
4 mm ( 0.16 in.) for b
5 mm ( 0.17 in.) for c
Install a nozzle that has been cut to a 4 mm ( 0.16
in.) or 7 mm (0.28 in.) or 5 mm (0.17 in.) opening.
HINT:
Avoid applying an excess amount to the surface.
Parts must be assembled within 15 minutes of ap-
plication. Otherwise, the material must be removed
and reapplied.
Immediately remove nozzle from tube and reinstall
cap after use.
(c) Install the oil pan with the 10 bolts.
Torque: 13 N´m (130 kgf´cm, 10 ft´lbf)
5. CONNECT FRONT EXHAUST PIPE
