1996 TOYOTA TERCEL washer fluid

MA003-28
MA-4
- MAINTENANCEUNDER HOOD
42 Author
: Date
:
1996 TERCEL (RM440U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL
Check that the coolant level is between the FULL and LOW lines on the see-through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leaves, dirt or bugs.
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upper and lower level lines on the case.
If level is low, add distilled water only.
6. BRAKE AND CLUTCH FLUID LEVELS
(a) Check that the brake fluid level is near the upper level line on the see-through reservoir.
(b) Check that the clutch fluid level is within ±5 mm (0.20 in.). of the reservoir hem.
7. ENGINE DRIVE BELTS
Check drive belt for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
(a) Check the level.
(b) The level should be in the HOT or COLD range depending on the fluid temperature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking brake applied, shift the selector into all positions from the P to
L, and then shift into the P position.
(c) Turn and pull out the dipstick and wipe off the fluid with a clean rag. Reinsert the dipstick and check
that the fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 - 80°C, 158 - 176°F).
If the If the level is at the low side, add fluid.
NOTICE:
Do not overfill.
HINT:
Wait until the engine cools down (approx. 30 min.) before checking the fluid level after extended driving at
high speeds, in hot weather, in heavy traffic or pulling a trailer.
11. EXHAUST SYSTEM
Visually inspect for cracks, holes or loose supports.
If any change in the sound of the exhaust or smell of the exhaust fumes is noticed, have the cause located
and corrected.

BR4387
BR3027
SST
BR0370
- BRAKEREAR DRUM BRAKE
BR-31
1996 TERCEL (RM440U)
(d) Using pliers, disconnect the parking brake cable from the
parking brake lever and remove the rear shoe.
6. REMOVE AUTOMATIC ADJUSTING LEVER AND
PARKING BRAKE LEVER
(a) Remove the E-ring.
(b) Remove the automatic adjusting lever.
(c) Remove the C-washer.
(d) Remove the parking brake lever.
7. REMOVE WHEEL CYLINDER
(a) Using SST, disconnect the brake line. Use a container to
catch the brake fluid.
SST 09751-3601 1
Torque: 15 N´m (155 kgf´cm, 11 ft´lbf)
(b) Remove the 2 bolts and the wheel cylinder.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
8. DISASSEMBLE WHEEL CYLINDER
Remove the these parts from the wheel cylinder.

2 boots

2 pistons

2 piston cups

Spring

R11071
Round End
R12361
R12362
- STEERINGPOWER STEERING VANE PUMP
SR-31
1996 TERCEL (RM440U)
6. INSTALL VANE PLATES
Install the 10 plates with the round end facing outward.
7. INSTALL SIDE REAR PLATe
(a) Coat a new O-ring with power steering fluid, and install
it to the plate.
(b) Align the holes of the plate and straight pins.
8. INSTALL WAVE WASHER
Install the washer so that its protrusions fit into the slots in the
side rear plate.
9. INSTALL REAR HOUSING
(a) Coat a new O-ring with power steering fluid and install it
to the rear housing.
(b) Install the rear housing and use a press to push down on
the wave washer hard enough to compress it.
NOTICE:

Do not apply too much pressure.

Be careful not to damage the O-ring.
10. INSTALL SPRING, FLOW CONTROL VALVE AND
PRESSURE PORT UNION
(a) Install the valve facing the correct direction.
(See page SR-22)
(b) Coat a new O-ring with power steering fluid, and install
it to the union.
(c) Torque the union.
Torque: 69 N´m (700 kgf´cm, 51 ft´lbf)
11. INSTALL SUCTION PORT UNION
(a) Coat a new O-ring with power steering fluid, and install
it to the union.
(b) Torque the 2 bolts.
Torque: 13 N´m (130 kgf´cm, 9 ft´lbf)

BE-4
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
1996 TERCEL (RM440U) Taillight does not light up. (Headlight does not light up)
1. Light Control Switch
2. Headlight Bulb
3. Wire HarnessBE-16
-
-
Headlight does not light up with light control SW in HEAD.
1. Light Control Switch
2. D.R.L. Main Relay
3. D.R.L. No.4 Relay (R/B No.5)
4. Daytime Resistor
5. Wire HarnessBE-16
BE-16
BE-16
BE-16
-
Headlight does not go out with light control SW in OFF.1. Headlight Control Relay (Engine Room R/B)
2. Wire HarnessBE-16
-
Taillight does not light up with light control SW in TAIL.
1. Taillight Control Relay (I/P J/B)
2. Light Control Switch
3. Wire HarnessBE-16
BE-16
-
Taillight does not go out with light control SW in OFF.
1. Taillight Control Relay (I/P J/B)
2. Light Control Switch
3. Wire HarnessBE-16
BE-16
-
Headlight do not light up with engine running and light control SW
in OFF.
1. DOME Fuse (Engine Room R/B)
2. ECU-IG Fuse (I/P J/B)
3. DRL Fuse (Engine Room R/B)
4. D.R.L. Main Relay
5. D.R.L. No.4 Relay (R/B No.5)
6. Daytime Resistor
7. Wire Harness
8. Generator L Terminal
9. Parking Brake Switch
10.Brake Fluid Level Warning Switch-
-
-
BE-16
BE-16
BE-16
-
-
BE-38
BE-38
TURN SIGNAL AND HAZARD WARNING SYSTEM
TroubleParts nameSee page
ºHazardº and ºTurnº do not light up.
1. Hazard Warning Switch
2. Turn Signal Flasher
3. Wire HarnessBE-22
BE-22
-
No of blinks for Hazard.
(Turn is abnormal)1. Bulb
2. Turn Signal Flasher
3. Wire Harness-
BE-22
-
Hazard warning light does not light up.
(Turn signal is normal)1. HAZ-HORN Fuse (Engine Room R/B)
2. Wire Harness-
-
Hazard waning light does not light up in one direction.1. Hazard Warning Switch
2. Wire HarnessBE-22
-
Turn signal does not light up.
(Combination meter, wiper and washer do not operate.)
1. Ignition Switch
2. TURN Fuse (Engine Room R/B)
3. Turn Signal Switch
4. Wire HarnessBE-1 1
-
BE-22
-
Turn signal does not light up.
(Combination meter, wiper and washer are normal.)1. TURN Fuse (Engine Room R/B)
2. Turn Signal Switch
3. Wire Harness-
BE-22
-

BE-6
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
1996 TERCEL (RM440U) Washer fluid does not operate.
1. Washer Hose and Nozzle-

At wiper switch HI position, the wiper blade is in contact with the
body.

When the wiper switch is OFF, the wiper blade does not retract
or the retract position is wrong.
1. *1 Wiper Switch
2. Wire harnessBE-30
-
*1: Inspect wiper arm and blade set position
COMBINATION METER (METER, GAUGES AND ILLUMINATION)
TroubleParts nameSee page
Tachometer, Fuel Gauge and Engine Coolant Temperature Gauge
do not operate.3. GAUGE Fuse (Engine Room R/B)
4. Meter Circuit
5. Wire Harness-
BE-35
-
Speedometer does not operate.
1. Vehicle Speed Sensor
2. Meter Circuit
3. Wire HarnessBE-38
BE-35
-
Tachometer does not operate.
1. Igniter
2. ECM
3. Meter Circuit
4. Wire Harness-
-
BE-35
-
Fuel Gauge does not operate or operate abnormally.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Meter Circuit
4. Wire HarnessBE-38
BE-38
BE-35
-
Engine Coolant Temperature Gauge does not operate or operate
abnormally.
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Meter Circuit
4. Wire HarnessBE-38
BE-38
BE-35
-
All illumination lights do not light up.
1. TAIL Fuse (I/P J/B)
2. Light Control Rheostat
3. Meter Circuit
4. Wire Harness-
BE-38
BE-35
-
Only one illumination light does not light up.1. Bulb
2. Meter Circuit-
BE-35
COMBINATION METER (WARNING LIGHTS)
TroubleParts nameSee page
Warning lights do not light up.
(Except Discharge, SRS and Door Open)
1. Bulb
2. GAUGE Fuse (I/P J/B)
3. Ignition Switch
4. Meter Circuit
5. Wire Harness-
-
BE-1 1
BE-35
-
Brake Warning Light does not light up.
1. Bulb
2. Brake Fluid Level Warning Switch
3. Parking Brake Switch
4. Bulb Check Relay
5. Meter Circuit
6. Wire Harness-
BE-38
BE-38
-
BE-35
-
Seat Belt Warning Light does not light up.
1. Bulb
2. Seat Belt Retractor Switch
3. Integration Relay
4. Meter Circuit
5. Wire Harness-
BE-38
BE-38
BE-35
-

BO33S-01
N15577
A
C
BA
B
D E
BE3367
2 ~ 2.5 mm
(0.079 ~ 0.098 in.)
0.7 ~ 0.75 mm
(0.028 ~ 0.030 in.) BO-28
- BODYFRONT WIPER AND WASHER
1996 TERCEL (RM440U)
ADJUSTMENT
1. INSPECT WASHER NOZZLE
(a) While operating the washer, check whether the upper
point where the washer fluid hits the windshield and the
upsurge area are within the range indicated by the
hatched line.
A: Approx. 150 mm (5.91 in.)
B: Approx. 50 mm (1.99 in.)
C: Approx. 0 - 50 mm (0 - 1.99 in.)
D: Approx. 30 mm (1.18 in.)
E: Approx. 20 mm (0.79 in.)
(b) Check if the lower point where the washer fluid hits the
windshield is within the range of the wiping pattern (the
area of the glass which is wiped by the wiper blades).
2. ADJUST WASHER NOZZLE
Using a tool like that one shown in the illustration, change the
direction of the nozzle hole to adjust the point where washer
fluid hits the windshield.