1996 TOYOTA TERCEL instrument panel

- INTRODUCTIONFOR ALL OF VEHICLES
IN-13
13 Author
: Date
:
1996 TERCEL (RM440U)
(f) AIRBAG SENSOR ASSEMBLY
(1) Never reuse the airbag sensor assembly involved
in a collision when the SRS has deployed.
(2) The connectors to the airbag sensor assembly
should be connected or disconnected with the sen-
sor mounted on the floor. If the connectors are con-
nected or disconnected while the airbag sensor as-
sembly is not mounted to the floor, it could cause
undesired deployment of the supplemental re-
straint system.
(3) Work must be started after 90 seconds from the
time the ignition switch is turned to the ºLOCKº posi-
tion and the negative (-) terminal cable is discon-
nected from the battery, even if only loosing the set
bolts of the airbag sensor assembly.
(g) WIRE HARNESS AND CONNECTOR
The SRS wire harness is integrated with the instrument
panel wire harness assembly and floor wire harness as-
sembly. The wires for the SRS wire harness are encased
in a yellow corrugated tube. All the connectors for the sys-
tem are also a standard yellow color. If the SRS wire har-
ness becomes disconnected or the connector becomes
broken due to an accident, etc., repair or replace it as
shown on page RS-37.

- INTRODUCTIONTERMS
IN-33
33 Author
: Date
:
1996 TERCEL (RM440U) H/B
Hatchback
H-FUSEHigh Current Fuse
HIHigh
HIDHigh Intensity Discharge (Head Lamp)
HPUHydraulic Power Unit
HSGHousing
HTHard Top
HWSHeated Windshield System
IACIdle Air Control
ICIntegrated circuit
IDIIndirect Diesel Injection
IFSIndependent Front Suspension
IGIgnition
IIAIntegrated Ignition Assembly
INIntake (Manifold, Valve)
INTIntermittent
I/PInstrument Panel
IRSIndependent Rear Suspension
J/BJunction Block
J/CJunction Connector
KDKick-Down
LANLocal Area Network
LBLiftback
LCDLiquid Crystal Display
LEDLight Emitting Diode
LHLeft-Hand
LHDLeft-Hand Drive
L/H/WLength, Height, Width
LLCLong-Life Coolant
LNGLiquified Natural Gas
LOLow
LPGLiquified Petroleum Gas
LSDLimited Slip Differential
LSP & PVLoad Sensing Proportioning And Bypass Valve
LSPVLoad Sensing Proportioning Valve
MAX.Maximum
M-FUSEMedium Current Fuse
MICMicrophone
MILMalfunction Indicator Lamp
MIN.Minimum
MPMultipurpose
MPXMultiplex Communication System
M/TManual Transmission (Transaxle)
MTMount
MTGMounting
NNeutral

FI0534
DI4LE-02
P19552
TOYOTA Hand-Held Tester
DLC3
- DIAGNOSTICSENGINE
DI-3
1996 TERCEL (RM440U)
PRE-CHECK
1. DIAGNOSIS SYSTEM
(a) Description

When troubleshooting OBD II vehicles, the only dif-
ference from the usual troubleshooting procedure
is that you need to connect OBD II scan tool comply-
ing with SAE 1978 or TOYOTA hand-held tester to
the vehicle and read off various data output from the
vehicle's ECM.

OBD II regulations require that the vehicle's on-
board computer lights up the Malfunction Indicator
Light (MIL) on the instrument panel when the com-
puter detects a malfunction in the computer itself or
in a drive system components which affect vehicle
emissions. In addition to the MIL lighting up when
a malfunction is detected, the applicable Diagnostic
Trouble Code (DTC) prescribed by SAE J2012 are
recorded in the ECM memory (See page DI-13).
If the malfunction does not reoccur in 3 trips, the MIL goes off
but the DTC remain recorded in the ECM memory.

To check the DTC, connect the OBD II scan tool or
TOYOTA hand-held tester to Data Link Connector
3 (DLC3) on the vehicle. The OBD II scan tool or
TOYOTA hand-held tester also enables you to
erase the DTC and check freezed frame data and
various forms of engine data (For operating instruc-
tions, see the OBD II scan tool's instruction book.).

DTC include SAE controlled codes and manufac-
turer controlled codes. SAE controlled codes must
be set as prescribed by the SAE, while manufactur-
er controlled codes can be set freely by the
manufacturer within the prescribed limits (See DTC
chart on page DI-13).

S00840
- DIAGNOSTICSENGINE
DI-5
1996 TERCEL (RM440U)Terminal No.
Connection / Voltage or ResistanceCondition
7Bus + Line / Pulse generationDuring transmission
4Chassis Ground - Body Ground / 1 W or lessAlways
5Signal Ground - Body Ground / 1 W or lessAlways
16Battery Positive - Body Ground / 9 - 14 VAlways
HINT:
If your display shows ºUNABLE TO CONNECT TO VEHICLEº
when you have connected the cable of the OBD II scan tool or
TOYOTA hand-held tester to DLC3, turned the ignition switch
ON and operated the scan tool, there is a problem on the ve-
hicle side or tool side.

If communication is normal when the tool is connected to
another vehicle, inspect DLC3 on the original vehicle.

If communication is still not possible when the tool is con-
nected to another vehicle, the problem is probably in the
tool its self, so consult the Service Department listed in
the tool's instruction manual.
2. Normal Mode:
INSPECT DIAGNOSIS
(a) Check the MIL.
(1) The MIL comes on when the ignition switch is turned
ON and the engine is not running.
HINT:
If the MIL does not light up, troubleshoot the combination meter.
(2) When the engine started, the MIL should go off. If
the lamp remains on, the diagnosis system has de-
tected a malfunction or abnormality in the system
(b) Check the DTC.
NOTICE:
TOYOTA hand-held tester only: When the diagnosis sys-
tem is switched from the normal mode to the check mode,
it erases all DTC and freeze frame data recorded in the nor-
mal mode. So before switching modes, always check the
DTC and freeze frame data, and note them down.
(1) Prepare the OBD II scan tool (complying with SAE
J 1978) or TOYOTA hand-held tester.
(2) Connect the OBD II scan tool or TOYOTA hand-
held tester to DLC3 in the fuse box at the lower left
of the instrument panel.
(3) Turn the ignition switch ON and turn the OBD II scan
tool or TOYOTA hand-held tester switch ON.
(4) Use the OBD II scan tool or TOYOTA hand-held
tester to check the DTC and freezed frame data;
note them down (For operating instructions, see the
OBD II scan tool's instruction book.).
(5) See page DI-13 to confirm the details of the
DTC.

FI3605
Flashing
ON
OFF
0.13 Seconds
DI-6
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
NOTICE:
When simulating symptoms with an OBD II scan tool (ex-
cluding TOYOTA hand-held tester) to check the DTC, use
the normal mode. For code on the DTC chart subject to º2
trip detection logicº, turn the ignition switch OFF after the
symptom is simulated the first time. Then repeat the simu-
lation process again. When the problem has been simu-
lated twice, the MIL lights up and the DTC are recorded in
the ECM.
3. Check Mode:
INSPECT DIAGNOSIS
HINT:
TOYOTA hand-held tester only:
Compared to the normal mode, the check mode has an in-
creased sensitivity to detect malfunctions.
Furthermore, the same diagnostic items which are detected in
the normal mode can also be detected in the check mode.
(a) Check the DTC.
(1) Initial conditions.

Battery positive voltage 11V or more.

Throttle valve fully closed.

Transmission in ºPº or ºNº position.

Air conditioning switched OFF.
(2) Turn the ignition switch OFF.
(3) Prepare the TOYOTA hand-held tester.
(4) Connect the TOYOTA hand-held tester to DLC3 in
the fuse box at the lower left of the instrument panel.
(5) Turn the ignition switch ON and switch the TOYOTA
hand-held tester ON.
(6) Switch the TOYOTA hand-held tester normal mode
to check mode. (Check that the MIL flashes.)
(7) Switch the engine. (The MIL goes out after the en-
gine start.)
(8) Simulate the conditions of the malfunction de-
scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTC, etc.
(9) After simulating the malfunction conditions, use the
TOYOTA hand-held tester diagnosis selector to
check the DTC and freezed frame data, etc.
HINT:
Take care not to turn the ignition switch OFF. Turning the ignition
switch OFF switches the diagnosis system from check mode to
normal mode, so all DTC, etc. are erased.
(10) After checking the DTC, inspect the applicable cir-
cuit.

P25914P25915A07081
TE1
E1 SST
DLC1
- DIAGNOSTICSENGINE
DI-9
1996 TERCEL (RM440U)
(e) Remove the fuse cover on the instrument panel.
(f) Connect the OBD II scan tool or TOYOTA hand-held tester to DLC3 on the vehicle.
CHECK:
Use CURRENT DATA to check the engine idle speed.
OK:
Idle speed: 700 - 800 rpm
NG Proceed to matrix chart of problem symptoms
on page DI-19.
OK
6 Check ignition timing.
PREPARATION:
(a) Warm up engine to normal operating temperature.
(b) Shift transmission into ºNº position.
(c) Keep the engine speed at idle.
(d) Using SST, connect terminals TE1 and E1 of DLC1.
SST 09843-18020
(e) Using a timing light, connect the tester to No.1 high-ten-
sion cord.
CHECK:
Check ignition timing.
OK:
Ignition timing: 10° BTDC at idle
NG Proceed to page IG-1 and continue to trouble-
shoot.
OK
Proceed to matrix chart of problem symp-
toms on page DI-19.

P25916
S00553
DI-10
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
7 Check fuel pressure.
PREPARATION:
(a) Be sure that enough fuel is in the tank.
(b) Turn ignition switch ON.
(c) Remove the fuse cover on the instrument panel.
(d) Connect the TOYOTA hand-held tester to DLC3 on the
vehicle.
(e) Use ACTIVE TEST mode to operate the fuel pump.
(f) If you have no TOYOTA hand-held tester, connect the
positive (+) and negative (-) leads from the battery to the
fuel pump connector (See page MF-1).
CHECK:
Check for fuel pressure in the inlet hose when it is pinched off.
HINT:
At this time, you will hear a fuel flowing noise.
NG Proceed to page MF-1 and continue to trouble-
shoot.
OK
8 Check for spark.
PREPARATION:
(a) Disconnect the high-tension cord from spark plug or re-
move the ignition coil.
(b) Remove spark plug.
(c) Install the spark plug to high-tension cord or ignition coil.
(d) Disconnect injector connector.
(e) Ground the spark plug.
CHECK:
Check if spark occurs while engine is being cranked.
NOTICE:
To prevent excess fuel being injected from the injectors
during this test, do not crank the engine for more than 5 -
10 seconds at a time.
NG Proceed to page IG-1 and continue to trouble-
shoot.
OK

A15677
- DIAGNOSTICSENGINE
DI-21
1996 TERCEL (RM440U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
If DTC P0105, P0110, P0115, P0120 are output simultaneously, E2 (sensor ground) may be open.
1 Connect OBD II scan tool or TOYOTA hand-held tester, and read value of man-
ifold absolute pressure.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(c) Turn the ignition switch ON and OBDII scan tool or TOYOTA hand-held tester main switch ON.
CHECK:
Read value of manifold absolute pressure on the OBD II scan tool or TOYOTA hand-held tester.
OK:
Same value as the atmospheric pressure
OK Check for intermittent problems (See page
DI-3).
NG